Table of Contents
Advertisement
Quick Links
NOTE:
The wireless hub and hub bracket are included with the K100-622H model.
Reader
Lock Body
Drill, Drill bits: 1/16", 3/16", 1/2"
Approved iCLASS or Prox ID
credential.
Wireless Frequency: 2.4 GHz, IEEE 802.15.4, using AES 128-bit encryption
Hub Power Requirement: 8–24 Volts Direct Current (VDC), 250 milliamps (mA)
Lock Battery Type: Lithium AA Cell, 1.5 Volts (V) (Energizer L91 Ultimate Lithium)
Battery Life: 50,000 cycles
Operating Temperature: 32 °F to 122 °F (0 °C to 50 °C)
FCC Part 15 Compliant, IC Compliant
Credentials Supported: (-PA) Low Frequency model: HID PROX, EM PROX
(-SE) High Frequency model: iCLASS, iCLASS SEOS , iCLASS SE, ISO14443B UID
Mifare, Mifare Plus, Desfire SE, Desfire EV1, NFC
3080076.004, Rev. B
K100-622 Aperio Series
Wireless Cabinet Lock
Installation Instructions
Package Contents
Template
Hub Bracket
Wireless Hub
Energizer L91 Ultimate
Recommended Tools
Flathead drivers 3/32", 3/16"
Phillips drivers P0, P2
Pencil, Wire Stripper, Level,
Square, Pliers
Product Specifications
For technical support please call 1-800-626-7590
Strike Plate
Key Override Paddle
Shaft Extension
Key Override
Lithium Batteries
2X
,
HES, Inc.
Phoenix, AZ
1.800.626.7590
www.hesinnovations.com
Screws
2-56 x 1-1/4"
6 x 1/2"
6-32 x 5/16"
1X
5X
3X
8-32 x 5/16"
1X
8-32 x 1 1/4"
Breakaway
3X
8-32 x 2 1/2"
2X
Double door bracket
Cam
Optional Additional Tools:
Gang box to mount hub
Cam Lock for Key Override
QR Codes
K100-622
Tips and Videos
QR codes can be scanned
with a smart phone app
2-56 x 7/16"
2X
8-32 x 2 3/4"
2X
1
Advertisement
Table of Contents
Related Manuals for Assa Abloy K100-622
Summary of Contents for Assa Abloy K100-622
- Page 1 K100-622 Aperio Series HES, Inc. Wireless Cabinet Lock Phoenix, AZ 1.800.626.7590 Installation Instructions www.hesinnovations.com Package Contents NOTE: The wireless hub and hub bracket are included with the K100-622H model. Template Strike Plate Reader Screws 2-56 x 1-1/4” 6 x 1/2”...
-
Page 2: System Overview
The K100-622 series wireless cabinet lock provides access control to a cabinet or drawer without the complexity and expense of running wires to the cabinet or drawer. The K100-622 series lock connects to an access control through a communication hub (included with the K100-622H). The communication hub connects to the access control system with Wiegand wiring typical of a Wiegand Reader. -
Page 3: Mounting The Hub
Choosing the hub location NOTE: The following applies primarily to the K100-622H Model with included hub. It is recommended that the hub be mounted near the top of a wall, on the ceiling or above the ceiling to reduce potential for interference, and be facing toward the lock for best performance. -
Page 4: Connecting The Hub
Connecting the Hub NOTE: The following applies primarily to the K100-622H Model with included hub. ® Hub connects to the Access Control system via Wiegand wiring. The hub requires 8–24 VDC power The Aperio (250mA). The hub includes three Form C relays that can be used to transmit latch bolt position status, low battery signal, and a tamper signal. - Page 5 Testing the Lock with the Access Control System NOTE: With the hub connected to power and the access control system, the lock is tested with a known good credential to confirm it will open as desired when installed. 1. REMOVE the battery cover from the 2.
-
Page 6: Mounting The Lock
The Installer must ensure the lock can be opened before closing the cabinet at the end of these installation instructions. Mounting the Lock NOTE: The K100-622 reader and lock body can be oriented in several ways to accommodate various cabinets and drawers. 1. ESTABLISH the horizontal centerline of the latch. - Page 7 2. TRANSFER the location of the inside wall of the cabinet to the door. 2a. MEASURE the horizontal distance between the inside edge of the cabinet and the door edge. NOTE: The drawn line depicts the location of the strike mounting surface. 2b.
- Page 8 4. INSTALL the Shaft Extension. 4a. IF the cabinet door thickness is greater than ½”, THEN INSTALL the Shaft Extension to the Antenna/Reader to ensure proper engagement into the lock. Shaft Extension 4b. INSTALL the Shaft Extension to the shaft as shown in the figure and firmly TIGHTEN the screw.
- Page 9 7. INSTALL the Antenna/Reader. ***CAUTION*** Pinching the wires may prevent the Reader and Lock from properly functioning. 7a. PLACE and HOLD the antenna/reader to the outside of cabinet, routing the wire through the 1/2” offset hole, and ENSURE the knob is in the locked position in the vertical.
- Page 10 9. Electrically CONNECT the antenna/reader wire to the lock body. NOTE: The antenna/reader wire connector is keyed to only fit one way. 9a. ENSURE correct orientation of the connector while inserting it. Connector cable tucked in 9b. TUCK excess cable into lock body as shown. 10.
- Page 11 ***CAUTION*** The Installer must ensure the lock can be opened before closing the cabinet. 12. INSTALL the single-door strike plate. 12a. PLACE the strike plate over the pilot holes, and INSERT and TIGHTEN the two screws in the slotted holes. 12b.
- Page 12 (1) cet appareil ne peut causer d’interférences, et (2) cet appareil doit accepter toute interference, y compris des interférences qui peuvent provoquer un fonctionnement indésirable du périphérique. For Technical Support please call 1-800-626-7590 © 2014, Hanchett Entry Systems, Inc., an ASSA ABLOY Group 3080076.004, Rev. B...