Page 1
HES K100 Aperio Series Wireless Cabinet Lock Installation and Operating Instructions AA Lithium Batteries required. Use of other types of batteries, such as alkaline, will significantly decrease battery life. Products Specifications Wireless Frequency: 2.4GHz, IEEE 802.15.4, using AES 128-bit encryption Lock Battery Type: AA Lithium, 1.5 Volts (V) Battery Life: 50,000 cycles* *All battery life claims are approximate and based on a set configuration profile.
Package Contents Installation Reader Lock Body Template Threadlock Strike Plate Mechanical Key Override Pillow Pack Double Door Hardware Bracket 2-56 X 7/16” 6-32 X 5/16” 6 X 1/2" 8-32 X 5/16” Lithium Batteries 8-32 Nut 8-32 X 2-3/4” 8-32 X 1-3/4” 8-32 X 2-1/2”...
Page 4
Lock Orientation Options Orientation B Orientation A Orientation C Prepping the Cabinet/Drawer Face . Separate Strike Plate Template. 2. Establish centerline (for double door cabinet prep go to page 6). Page 4 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1...
Page 5
3. Measure cabinet wall thickness and mark 4. Continue centerline to face of offset line on face of cabinet/drawer. The cabinet/drawer offset line should match with the interior edge of the cabinet wall. 5. Align template to offset line and 6.
Page 6
Prepping the Cabinet/Drawer Face (Double Door) 1. Establish center line on inside 2. Continue center line onto of stationary door. outside face of cabinet. 3. Align offset line on template to the edge of the stationary door and align center line with the established center line above.
Reader Installation 1. Align reader with mounting holes and pull 2. Add Threadlock to threaded rod. cable through as shown. Trim Threaded rod Secure Reader to cabinet/drawer using to length as outlined in table 2. the cut threaded rod and coupling nut. DO NOT overtighten.
Page 8
Lock Body Installation 1. Insert reader cable through hole 2. Align lock body to mounting holes in back of lock body. andsecure to cabinet/drawer face using 2x screw F and 2x screw D. If thick cabinet/drawer then use 2x screw E or 2x screw G instead of 2x screw F.
Installing the Batteries 1. Install AA lithium batteries in appropriate 2. Install cover and secure using 2x position. screw A. Mechanical Key Override (Optional) Mechanical key override cam lock sold 1. Insert cam lock through the outside separately. of the cabinet/drawer face and secure with locking nut.
Strike Plate Installation 1. Align strike plate template to centerline 2. Secure strike plate to inside cabinet and edge of cabinet. Drill mounting holes. wall using 2x screw D, but do not fully tighten. Adjust strike plate so the edge is flush with the cabinet wall edge then tighten.
Page 11
Double Door Strike Installation 1. Align Double door bracket with mounting holes from the strike plate template. Secure double door bracket using 3x screw D. 2. Secure strike plate to double door bracket using 3x screw D as shown below. Page 11 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1...
LED Codes Page 12 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1...
Page 13
Aperio Hub Technical Data – AH20 Approvals CE, ETL, FCC, IC, C-Tick Safety and emissions FCC 47CFR Part 15 subpart B and subpart C; IC RSS-210 EN ETSI 301 489-17 v2.1.1; ENETSI 300 328 v1.7.1; EN 60950-1 ed.2 2007 Dimensions 82x82x37 Power Supply 8-24 VDC...
Connecting the Hub The following applies only to Aperio factory paired kits with AH20 Hubs. Connect the Wiegand D1, D0, red, and green LED signals. Note: The Green LED input is used to grant access to the cabinet lock. If the Green LED signal is not available to indicate approved access, the approval input can be activated by a relay with “NO”...
FCC Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 16
Conformité aux normes IC Cet appareil est confrome avec Industrie Canada exempt de license RSS standard(s). Son fonctionnement est souimes aux deux conditions suivantes: (1) cet appareil ne peut causer d’interférences, et (2) cet appareil doit accepter toute interference, y compris des interférences qui peuvent provoquer un fonctionnement indésirable du périphérique.
Need help?
Do you have a question about the Aperio Series and is the answer not in the manual?
Questions and answers