Festool TKS 80 EBS Original Instructions Manual page 36

The cross and angle stop (Fig. 6b) is ready for
use.
Adjusting the preset profile setting rail: Set­
ting the parallelism
► Set the stop rail [6-7] at a right angle to the
saw blade (see section
► Undo the hexagon socket head
screws [6-13].
► Place a protractor between the saw blade
and the sliding handle [6-2].
► Using the protractor, adjust the sliding han­
dle [6-2] to 90°.
► Tighten the hexagon socket head
screws [6-13].
9.6 Table insert
Removing the table insert
► Open the table insert [7-1] with a span­
ner [7-2] in the direction of the arrow.
► Remove the table insert [7-1].
Fitting the table insert
► Insert the table insert [7-1] into the table
and lock it into place.
WARNING
Risk of accidents due to kickback
► Make sure that the table insert is correctly
inserted and forms an even surface with
the saw table.
9.7 Protective cover
Fitting the protective cover
► Set the saw blade to maximum cutting
height (see section
► Set the mitre angle to 0° (see section
► Unscrew the screw [8-2] from the protec­
tive cover [8-1].
► Insert the lengthwise pin situated in the
protective cover [8-1] into the groove [8-4]
of the spacer wedge [8-5].
► Re-insert the screw [8-2] into the protective
cover [8-1] and through the hole in the
spacer wedge [8-3] and tighten it.
Removing the protective cover
► Set the saw blade to maximum cutting
height (see section
► Set the mitre angle to 0° (see section
► Tighten the protective cover [8-1] and un­
screw the screw [8-2].
► Pull the lengthwise pin situated in the
protective cover out of the groove [8-4] of
the spacer wedge [8-5] and remove the
protective cover [8-1].
9.5 ).
9.3 ).
9.4
9.3 ).
9.4
► Re-insert the screw [8-2] into the protective
cover [8-1] and tighten it.
Setting the protective cover
► Release the rotary knob [8-8].
► To adjust the preset profile setting rail, lock
the side splinter guard of the protective cov­
er [8-6] with the snap-in nose [8-7] in the
top position.
► Lift the protective cover into the top po­
sition and tighten the rotary knob [8-8].
► After adjusting the preset profile setting
rail, loosen the rotary knob [8-8] again and
unhook the side splinter guard of the pro­
tective cover [8-6].
The protective cover [8-1] and the
splinter guard of the protective cov­
er [8-6] must lie freely on the plate.
9.8 Changing the spacer wedge
Use a spacer wedge with protective cov­
er [9-1] for rip and angled cuts.
Use a spacer wedge for cutting
grooves [9-2] for concealed cuts.
Risk of accidents due to kickback
► The safety equipment must be re-installed
immediately after work that requires the
spacer wedge with protective cover to be
removed.
With fitted table insert
► Set the cutting height to the maximum of
80 mm (see section
).
► Remove the hex key [9-4] from the hold­
er [9-5].
► Fully insert the hex key [9-4] into the open­
ing [9-3].
► Turn the hex key [9-4] anticlockwise as far
as it will go.
► Remove and/or replace the spacer wedge
(Fig. 9c).
► Remove the hex key [9-4] and store it in the
holder [9-5].
With removed table insert
► Turn the lever handle [9-6] anticlockwise as
).
far as it will go (Fig. 9b).
► Remove and/or replace the spacer wedge
(Fig. 9c).
WARNING
9.3 ).
English
37