Therefore, the following checks should be performed for the continued protection of the customer and servicetechnician. PDP-5050SX...
Page 3
PRODUCT SAFETY NOTICE With the AC plug removed from an AC power source, place a Many electrical and mechanical parts in PIONEER set have jumper across the two plug prongs. Turn the AC power switch on. special safety related characteristics. These are often not evident...
Page 4
(See "7.1.5 Power on/off function for the large- : Part is the High Voltage Generating Points signal system".) other than the Charged Section. For PDP-5050SX MR POWER SUPPLY Unit 50 SCAN B Assy 50 Y DRIVE Assy...
Page 5
PANEL POWER SUPPLY Unit 43 X DRIVE Assy X CONNECTOR A Assy AC SEPA Assy AC Inlet with Filter Power Cord X CONNECTOR Power Switch 43 SCAN A Assy (S1) B Assy Fig.1 Charged Section and High Voltage Generating Point (Rear View) PDP-5050SX...
Page 6
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. PDP-5050SX...
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PDP-5050SX 2.1.1 PACKING SECTION PDP-5050SX...
Page 11
Warranty Card ARY1138 DCR User Card ARY1162 NSP 13 User Card VRY1132 Pad (50T-L) AHA2439 Pad (50T-R) AHA2440 Pad (50B-L) AHA2441 Pad (50B-R) AHA2442 Accessory Case (SX) AHC1066 Under Carton (5050) AHD3358 Upper Carton (5050) AHD3352 Mirror Mat AHG1284 PDP-5050SX...
No. 20. 22 20 Refer to "2.1.7 MULTI BASE ASSY". 1 Cushions of No. 17, 18 and 19 cannot be reused once they are peeled off. When they are to be removed, order new parts. Refer to "2.1.3 FRONT SECTION". PDP-5050SX...
2.1.3 FRONT SECTION Refer to "2.1.4 - 2.1.6 CHASSIS SECTION (1/3 - 3/3)". PDP-5050SX...
Page 15
Mark No. Description Part No. KEY Assy AWW1011 Front Case Assy (5050) AMB2860 NSP 3 Front Case (50P) AMB2823 Pioneer Badge AAM1098 NSP 5 SR Lens (P) AAK2798 NSP 6 Function Button AAC1555 Panel Cushion V (50) AED1258 Panel Cushion H (50)
No. 20. Refer to Cushions of No. 17, 18 and 19 cannot be "2.1.7 MULTI BASE ASSY". reused once they are peeled off. When they are to be removed, order new parts. 10 8 Refer to "2.2.3 FRONT SECTION". PDP-5050SX...
2.2.3 FRONT SECTION Refer to "2.2.4 - 2.2.6 CHASSIS SECTION (1/3 - 3/3)". PDP-5050SX...
Page 31
Mark No. Description Part No. KEY Assy AWW1011 Front Case Assy (4350) AMB2859 NSP 3 Front Case (43P) AMB2821 Pioneer Badge AAM1096 NSP 5 SR Lens (P) AAK2798 NSP 6 Function Button AAC1555 Panel Cushion V (43) AED1256 Panel Cushion H (43)
BLOCK V+3V_LVDS V+3V_PLL V+ADR V+3V_LVDS V+3V_PLL V+ADR V+3V_IC5 V+3V_IC5 V+9V V+60V V+9V V+60V V+5V V+5V DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC IC1552 IC1553 IC1554 IC1555 IC1552 IC1553 IC1554 IC1555 PDP-5050SX...
Page 41
BLOCK V+3V_LVDS V+3V_PLL V+ADR V+3V_LVDS V+3V_PLL V+ADR V+3V_IC5 V+3V_IC5 V+9V V+60V V+9V V+60V V+5V V+5V DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC IC1552 IC1553 IC1554 IC1555 IC1552 IC1553 IC1554 IC1555 PDP-5050SX...
3.1.2 OVERALL BLOCK DIAGRAM (1/2) FOR PDP-5050SX DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC IC1551 IC1552 IC1553 IC1554 IC1555 IC1551 IC1552 IC1553 IC1554 IC1555 V+5V V+5V V+9V...
Page 43
V+ADR V+3V_IC5 V+3V_IC5 V+9V V+60V V+9V V+60V V+5V V+5V DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC IC1551 IC1552 IC1553 IC1554 IC1555 IC1551 IC1552 IC1553 IC1554 IC1555 PDP-5050SX...
+9.0V WOW IC VOLUME IC IC3502 IC3501 R_Audio L_Audio SCL, SDA BUFFER SRS,FOCUS,TRUBASS +6.5V +9.0V A_Mute ST-BY +16.5V +16.5V A_NG_B REGULATOR POWER AMP IC CN3501 IC3503 IC3504 DC DETECT BLOCK CN3503 J3701 SP TERMINAL ASSY R OUT L OUT PDP-5050SX...
Page 68
FIELD FIELD 25 FIELD control signal 0VDC GND_D GND_D DDC_SCL 0.0/5.0 DDC_SCL 27 I2C signal for DDC 0-5V amplitude square wave DDC_SDA 0.0/5.0 DDC_SDA 28 I2C signal for DDC 0-5V amplitude square wave GND_D GND_D GND_D GND_D GND_D GND_D PDP-5050SX...
Page 69
Signal Name RXD_SR4 0.0/3.3 RXD_SR4 TXD_SR4 0.0/3.3 TXD_SR4 PANEL POWER AUDIO AMP ASSY SUPPLY UNIT CN3504 (B3P-VH) P6 (B3P-VH) SR_OUT SR_OUT Voltage Signal Name Signal Name +16.5V 16.4 +16.5V V+12V 12.0 V+12V N.C. N.C. GND_VCC GND_VCC HDMI_EXT_RCH HDMI_EXT_RCH HDMI_EXT_LCH HDMI_EXT_LCH PDP-5050SX...
Page 70
Signal Description Voltages at NTSC Signal Input Signal Name Signal Name STBGND STBGND 0V DC Key scan signal 0V DC Key scan signal 0V DC Key scan signal +3.3V DC Key scan signal +3.3V DC Key scan signal +3.3V DC PDP-5050SX...
5 6 2 1 Mark No. Description Part No. Mark No. Description Part No. LIST OF ASSEMBLIES for PDP-4350SX LIST OF ASSEMBLIES for PDP-5050SX NSP 1..43 ADDRESS ASSY AWV2076 NSP 1..50 ADDRESS ASSY AWV2080 2..43 ADDRESS ASSY AWZ6862 2..50 ADDRESS ASSY AWZ6870 NSP 1..43 SCAN ASSY...
Refer to the "7.1.6 BACKUP WHEN THE MAIN UNIT IS ADJUSTED. " 43 (50) X DRIVE Assy No adjustment required 43 (50) Y DRIVE Assy No adjustment required Service Panel Refer to the "6.9 METHOD FOR REPLACING THE SERVICE PANEL ASSY. " Other assemblies No adjustment required PDP-5050SX...
Page 93
Press HOME MENU. 4 MSP Adjustment Select “Tuner Setup”. ( then ENTER) 5 MSP Adjustment Select “Channel Setup”. ( then ENTER) Select “POD ID”. ( • The Host ID and Cable Card ID appear. Press HOME MENU to exit the menu. PDP-5050SX...
About 2.5V (input signal) VGS waveform (output signal) Adjust so that the delay is in the range of 375 ± 10 ns. • Actually measured waveforms 500us/div 50ns/div Input signal: 1V/div Magnify. Output FET VGS 5V/div VGS=5V line PDP-5050SX...
6.3 ADJUSTMENT ITEMS If readjustment is necessary because of adjustment error at shipment, perform adjustments as shown below. ¶ Adjustment Points AV BOARD ASSY Upper side SIDE A SIDE A SIDE B PDP-5050SX...
Page 96
Equipment : SG, Oscilloscope Condition : Input RF level 60dBµV Modulation 87.5% White bar 100% Adjust TP7513 to 1.0 ± 0.05Vp-p 1.0 ± 0.05Vp-p START Select ANT B 55.25 MHz Oscilloscope VR7505 (AV BOARD Assy) TP7513 (AV BOARD Assy) PDP-5050SX...
Page 97
Equipment : SG, Oscilloscope Condition : Input RF level 60dBµV 300Hz STEREO 100% Lch Only Adjust Turn the wave pattern into a minimum. minimum START Select ANT A 67.25 MHz Oscilloscope VR7506 (AV BOARD Assy) TP7503 (AV BOARD Assy) PDP-5050SX...
Page 98
Equipment : SG, Oscilloscope Condition : Input RF level 60dBµV 5kHz STEREO 100% Lch Only Adjust Turn the wave pattern into a minimum. minimum START Select ANT A 175.25 MHz Oscilloscope VR7503 (AV BOARD Assy) TP7503 (AV BOARD Assy) PDP-5050SX...
The TRAP switch is disabled while the unit is turned off. When performing internal diagnosis of the PDP, fix the switch to the OFF position using adhesive tape before turning on the unit. After servicing, be sure to remove the adhesive tape. TRAP switch PDP-5050SX...
(effective when Function is set to TV) Function: TV Numeric keys Function: TV (previously selected channel number is selected) Power OFF Turning the power off FACTORY Factory OFF Turning Service Factory mode off HOME MENU Menu ON Turning Service Factory mode off PDP-5050SX...
Page 101
6. AFT LOCK MUTING 13. CH PRESET 14. ANTENNA MODE 3 INDIVIDUAL mode 1. CVY GAIN 2. RY GAIN MUTING 3. GY GAIN 4. BY GAIN MUTING 4 COMMON ADJ. mode 1. RGB 1 3. PANEL 1 4. PANEL 2 PDP-5050SX...
Page 102
S Q - D T - P 2 0 0 X (*1) (*1) 200X: PDP-4350SX, 210W: PDP-5050SX Main-item indications Four parameters are displayed: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 I N F O R M A T I O N V D 1 –...
Page 103
– Out of range Third character: Selection of the screen size by the user is displayed. (?: available, ×: not available) 3rd Character Description on GUI Remarks 4 : 3 FULL (FULL1) ZOOM CINEMA WIDE Indude WIDE-HD FULL2 HDTV1035i PDP-5050SX...
Page 104
S E Q - P R G - 0 6 A (*1) S Q - D T - V 2 0 0 X (*1) 200X: PDP-4350SX, 210W: PDP-5050SX S Q - D T - P 2 0 0 X (*1) Flash memory of Device...
Page 105
Backup EEPROM (2K) : IC7405, VOL IC : IC3502] Abnormality in RST2 RST2 Abnormality in panel temperature (TEMP1) TEMP1 Short-circuiting of the speakers AUDIO • DATA on MD-IIC subcategories Defective Communication Part EROM4K IC5201: Module microcomputer EEPROM EROM2K IC7405: EEPROM for backup IC3502: VOLUME IC VOLIC PDP-5050SX...
Page 106
IC6 (IC6951), CCD (IC8903), FE1 (U7501), FE2 (U7502), AV-SW1 (IC8002), AV-SW2 (IC8005) AV-EEP AV-EEP (IC8705) PS/RST No power, or reset status continued Interval UART Communication RETRY The signal 0x02 (ready) has not been received. DEVICE Receive System Query Request Command PDP-5050SX...
Page 107
N F O R M A T I O N V D 1 – 1 3 1 – N T V – A T O E T E R 0 0 1 5 1 H 2 1 M The cumulative power-on time of the MR side is displayed. PDP-5050SX...
Page 108
V D 1 – 1 3 1 – N T V – A T O C U N T E R 0 0 0 0 0 0 0 0 T I M E S The cumulative number of times the panel was turned on is displayed. PDP-5050SX...
Page 109
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 N F O R M A T I O N V D 1 – 1 3 1 – N T V – A T O E E P R OM Y E S PDP-5050SX...
Page 110
O G R A M N U M B D E O P I D D I O P I D P I D F O R A 0 8 0 I / 1 6 : 9 D E O PDP-5050SX...
Page 111
For production line use only Stop AFT tuner received function and receive a center frequency. After turning off a unit (including stand-by mode), this setting is set normal (AFT function) automatically. It's performed to two tuner and DTV tuner to U.S. model. PDP-5050SX...
Page 112
• Frequency selection while the mask is displayed Corresponding No. Function/Display Content RS-232C Command Not used (Video 50-Hz sequence) V60 (initial value) Video 60-Hz sequence Not used (PC 60-Hz sequence) Not used (PC 70-Hz sequence) Video 72-Hz sequence Not used (Video 75-Hz sequence) PDP-5050SX...
Page 113
9600-232C To set to RS-232C (9600 BPS) 19200-232C To set to RS-232C (19200 BPS) 38400-232C To set to RS-232C (38400 BPS) Tips: How to change the SR+/RS-232C setting without entering Service Factory mode Refer to "6.6 USING RS-232C COMMANDS". PDP-5050SX...
6.6 USING RS-232C COMMANDS For the PDP-4350SX and PDP-5050SX series Plasma Displays, the circuitry is structured as shown in the diagram below to support the SR+ system. Controlling with either the SR+ system or RS-232C commands can be selected. As the SR+ system is selected at shipment, to control with RS-232C commands in servicing it is necessary to switch the paths.
Turning Service Factory mode on Executing the FINAL SETUP Obtaining various adjustment values Switching the gamma Obtaining the shutdown (SD2) information Obtaining the value of P ON COUNTER Obtaining the power-down-point log Obtaining the PULSE METER data Obtaining the panel white-balance adjustment values PDP-5050SX...
Page 117
Panel white-balance adjustment: Blue highlight Panel white-balance adjustment: Blue low light The PD signal is not passed through the POWER SUPPLY Assy. The PD signal is passed through the POWER SUPPLY Assy. Panel white-balance adjustment: Green highlight Panel white-balance adjustment: Green low light PDP-5050SX...
Page 118
Increasing the adjustment value by * [*: 1-9, 0 (0 means 10), or F (making the adjustment value the maximum)] VMTS00 Canceling panel muting VMTS01 Panel muting Offset voltage adjustment Adjusting the audio volume CVY GAIN SUS voltage adjustment PDP-5050SX...
Page 119
U1 leading-edge pulse of X-SUS U2 leading-edge pulse of X-SUS D1 trailing-edge pulse of Y-SUS D2 trailing-edge pulse of Y-SUS D3 trailing-edge pulse of Y-SUS D4 trailing-edge pulse of Y-SUS U1 leading-edge pulse of Y-SUS U2 leading-edge pulse of Y-SUS PDP-5050SX...
3 bytes 000 - 255 Y-SUS-D2-1 adjustment value (YD3) 3 bytes 000 - 255 Note: Ignore the 2-byte checksum at the end. Data Table ABL table for NTSC Not used (ABL table for PAL) Not used (ABL table for PC) PDP-5050SX...
Page 121
Data of hour meter for the eighth latest PD 7 bytes 1st-5th byte: Hour, 6th-7th byte: Minute Data on temperature for the eighth latest PD (TEMP1) 3 bytes 000 - 255 Notes: • Ignore the 2-byte checksum at the end. • For details, see "Description on power-down." PDP-5050SX...
Page 122
(∗1) Each time hour-meter data are cleared, the accumulated time data are updated. The total for data items 15 and 16 is the total power-on time after shipment. The accumulated time of cleared hour-meter data cannot be cleared. (∗2) The hour-meter data that indicate driving hours of the panel are displayed on the Factory menu. Upon shipment, the data are cleared. PDP-5050SX...
Page 123
Abnormality in RST2 (power decrease of DC-DC converter) Volume IC (AUDIO Assy: IC3502) Panel having high temperature Reservation Audio failure (speakers short-circuited) Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation PDP-5050SX...
Page 124
No subcategory (DTV for North America) Communication failure of the DTV microcomputer (PS/RST) DTV NG (DEVICE) DTV microcomputer (CMD) DTV microcomputer communication (RETRY) Not used [PC CARD Communication NG (CD-COM)] Not used [PC CARD Mdule (CD-DEV)] Not used [PC CARD Reset NG (CD-RST)] PDP-5050SX...
Page 125
Version of the IC3 boot Software 4 bytes Version of the IC3 Program 4 bytes Data Model 4 bytes Version of the IC3 Enhanced PDP-5050SX Version of the IC3 GUI 4 bytes PDP-4350SX GPM: Returning the data of the PDP pulse meter Order Data Size...
Using the MUTE key, select the main item "INFORMATION." Select the subitem "HOUR METER," using the 5 or ∞ key and SET key. Clear the hour-meter data. In the same way, select the subitem "PULSE METER," "SD1," or "PD" under the main item "INFORMATION" then clear the data. PDP-5050SX...
7. GENERAL INFORMATION 7.1 DIAGNOSIS 7.1.1 PCB LOCATION PDP-5050SX 50 Y DRIVE Assy 50 ADDRESS Assy PANEL SENSOR Assy 50 SCAN B Assy DIGITAL VIDEO Assy PANEL POWER SUPPLY Unit 50 ADDRESS Assy 50 SCAN A Assy KEY Assy PANEL IR Assy...
Page 128
KEY CONTROL Assy SUPPLY Unit X CONNECTOR B Assy 43 ADDRESS Assy AC SEPA Assy 43 ADDRESS Assy LED Assy • Multi Base Assy AV BOARD Assy AUDIO AMP Assy MAIN BOARD Assy SP TERMINAL Assy SR Assy TUNER BOARD Assy PDP-5050SX...
Purpose: For improving the yield by compensating for the temperature characteristics of the panel Note: Temperature compensation is performed only for the VSUS voltage, and not for the VOFS voltage. This compensation is controlled by the software. PDP-5050SX...
CIRCUIT FAN_NG3 (H_act) FAN_NG3 AV BOARD Assy Specifications for port monitoring Port Name SD/PD Indication Assigned Pin Active FAN_NG Shutdown with H FAN_NG 3 Shutdown with H TEMP2 Abnormally high Shutdown when the temperature value exceeds the predetermined value PDP-5050SX...
Page 137
TRAP_SW Circuit diagram TRAP_SW MAIN BOARD Assy V+3V_COM TRAP_SW MAIN_UCOM PULL_D Specifications for port monitoring Port Name SD/PD Indication Assigned Pin Active TRAP_SW Modification tried OFF with L PDP-5050SX...
• Although the "DRF" RS-232C command is enabled during Standby, if the power is turned on then turned off, the unit will return to "DRN" mode. S5201 S5201 Drive OFF Normal position Fig. Drive OFF switch PDP-5050SX...
DIGITAL VIDEO Assy will be copied to Area B of the MAIN BOARD Assy of Unit 2, overwriting the data necessary for Unit 2. Once overwritten, the original data will not be restored. PDP-5050SX...
Page 140
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 N F O R M A T I O N V D 1 – 1 3 1 – N T V – A T O E E P R OM Y E S PDP-5050SX...
Page 141
Note: To cancel adjusted data and return to the values before adjustment, send the "BCP" RS-232C command. Turn the AC power off then turn it back on before setting the unit to Standby OFF. The backup values are then retrieved. PDP-5050SX...
Page 143
BOARD Assy is replaced? MAIN BOARD ASSY AV BOARD ASSY Finishing troubleshooting • For check the communication with the microcomputer, refer to the section 6.5 SERVICE FACTORY MODE. • The encircled numbers denote measuring point in the Waveforms for Troubleshooting. PDP-5050SX...
Page 144
IC8002? between IC8002 and the (41) microcomputer. Has the signal arrived at Check the communication TP7719? between IC8002 and TP7719. Check around the jack, or confirm that "Monitor Out" of HOME MENU is set correctly. (See the operating instructions.) PDP-5050SX...
Page 145
IC on the found to have a failure in MAIN BOARD Assy and communication and the the microcomputer normal? microcomputer. Has the symptom been settled when the MAIN The panel is defective. BOARD Assy is replaced? Finishing troubleshooting PDP-5050SX...
Page 146
Is the volume set to 0? check again. Is a signal output from IC8003? Check around IC8003 and (3) (13) check each input signal. Check around the jack, or confirm that "Monitor Out" of HOME MENU is set correctly. (See the operating instructions.) PDP-5050SX...
Page 147
Is a signal input to IC8002? Check the communications (62), (64) between IC7503 and Is a signal input to IC8002? Check the communications IC8002. between the jack and IC8002. Check around IC8002 and check the communications between IC8002 and the microcomputer. PDP-5050SX...
Page 148
TUNER BOARD ASSY. Has the signal arrived at Check the cable between the TP3512 and TP3513? AV BOARD Assy and AUDIO AMP Assy. Has the symptom been Replace settled when the system AUDIO AMP ASSY. cable is replaced? Finishing troubleshooting PDP-5050SX...
7.1.8 DISASSEMBLY Note : Even if the unit shown in the photos and illustrations in this manual may differ from your product, the procedures described here are common. PDP-5050SX Rear Section Rear Case (5050) Rear case (5050) Remove the screws.
Page 154
Unhook the three hooks. Front case Assy (5050) Remove the front case Assy (5050). KEY Assy Panel Holder V (50) Remove the ten screws. Remove the two panel holder V (50)s. Panel holder V (50) Panel holder V (50) PDP-5050SX...
Page 155
Remove the three screws. Remove the front chassis VR (5050). Front chassis VR (5050) Remove the seven screws. Remove the X CONNECTOR A and B Assys. 50 X DRIVE Assy ×4 ×3 X CONNECTOR B X CONNECTOR A Assy Assy PDP-5050SX...
Page 156
Disconnect the two pin connectors. 50 Y DRIVE Assy Remove the two PCB spacers. Remove the four edge card spacers. ×3 ×3 Remove the 50 SCAN A and B Assys. ×2 50 SCAN B 50 SCAN A Assy Assy PDP-5050SX...
Page 157
MULTI BASE SECTION (PDP-5050SX and PDP-4350SX) Note: To access the multi base section, only the rear case and under cover must be removed. No other parts need to be removed. MR POWER SUPPLY Unit Section ×3 Remove the one screw.
Page 158
Remove the 17 screws. Remove the under cover (4350). Under cover (4350) Note: If you wish to remove only the front case Assy (4350), remove it as follows. Rear case (4350) Remove the six screws. Remove the five screws. Under cover (4350) PDP-5050SX...
Page 159
Unhook the three hooks. Front case Assy (4350) Remove the front case Assy (4350). KEY Assy Panel Holder V (43) Remove the ten screws. Remove the two panel holder V (43)s. Panel holder V (43) Panel holder V (43) PDP-5050SX...
Page 160
Remove the three screws. Remove the front chassis VR (4350). Front chassis VR (4350) Remove the seven screws. Remove the X CONNECTOR A and B Assys. 43 X DRIVE Assy ×3 ×4 X CONNECTOR B X CONNECTOR A Assy Assy PDP-5050SX...
Page 161
Disconnect the two pin connectors. 43 Y DRIVE Assy Remove the two PCB spacers. Remove the four edge card spacers. ×2 ×2 Remove the 43 SCAN A and B Assys. ×2 43 SCAN B 43 SCAN A Assy Assy PDP-5050SX...
Page 171
CLR pin: H = All output High Ground GND pin Ground GND pin Not connected Supply High-voltage circuit supply pin VDDH VDDH Supply High-voltage circuit supply pin Not connected OUT1 Output High-voltage push-pull output pin OUT2 Output High-voltage push-pull output pin PDP-5050SX...
Page 172
BA8274F (DIGITAL VIDEO ASSY: IC4206) • I C Bus Interface IC Block Diagram N.C. Buffer Buffer N.C. Pin Function Pin No. Equivalent Circuit Pin Function Name Buffer output 35.7 Buffer input 35.7 Ground Power supply PDP-5050SX...
Page 176
Pin Function Equivalent Circuit Name SDIP42 SOP40 QFP48 V+/2 FFR2 FFL2 V+/2 VREF FIL1 V+/2 VREF PDP-5050SX...
Page 177
Block Diagram to DQ Erase Voltage Input/Output Buffers Generator State Control BYTE Command Register Program Voltage Generator Chip Enable Data Latch Output Enable Logic Y-Gating Y-Decoder Timer for Address Low V Detector Program/Erase Latch X-Decoder Cell Matrix to A PDP-5050SX...
Page 178
HDCP HDCP -------------- Decryption Keys Configuration Logic Engine E EPROM SCLS Slave SDAS CTL3 QE[23:0] RXC ± PanelLink QO[23:0] Panel TMDS RX0± Mask ODCK encrypted Interface unencrypted Digital RX1± data data Logic Core RX2± HSYNC control VSYNC EXT_RES SCDT PDP-5050SX...
Page 179
Setting pin for flash rewriting mode (pull-up) PSIZE Panel size distinction B_SCL IIC clock output for backup EEPROM B_SDA IIC DATA I/O for backup EEPROM ADR_PD PD signal of address junction LED_G Green LED control LED_R Red LED control PDP-5050SX...
Page 180
[A/D] Operation mode setting − − AVSS GND for A/D input MODEL [A/D] CMX/HD/TV/WX distinction − − VREF Reference voltage for A/D input − − AVCC Power supply for A/D input = STB3.3V NC pin NC pin AMG_MD Address emergency monitor PDP-5050SX...
Page 181
Address LVDS signal output AF19 AD0TXOUT3M Address LVDS signal output AF20 AD0TXCLKOUTM Address LVDS signal output AF21 AD0TXOUT2M Address LVDS signal output AF22 AD0TXOUT1M Address LVDS signal output AF23 AD0TXOUT0M Address LVDS signal output AF24 VSSL15 AF25 AD4TXOUT3P Address LVDS signal output PDP-5050SX...
Page 182
B phase signal input of B video (0 bit) VD signal input RAI_5 A phase signal input of R video (fifth bit) DCLKI CLK input GAI_4 A phase signal input of G video (fourth bit) BAI_9 A phase signal input of B video (ninth bit) PDP-5050SX...
Page 183
Address LVDS signal output AE22 AD0TXOUT1P Address LVDS signal output AE23 AD0TXOUT0P Address LVDS signal output AE24 VSSL15 AE25 AD4TXCLKOUTP Address LVDS signal output AD25 AD4TXOUT2P Address LVDS signal output AC25 AD4TXOUT1P Address LVDS signal output AB25 AD4TXOUT0P Address LVDS signal output PDP-5050SX...
Page 184
3.3V power supply GAI_1 A phase signal input of G video (first bit) GAI_0 A phase signal input of G video (0 bit) NC pin XSUSB_14 X-Drive control signal output VDDIO 3.3V power supply XSUSB_8 X-Drive control signal output PDP-5050SX...
Page 185
VSSLA VSSLA VSSLA SDITDO JTAG signal GPIO0_7 Microcomputer macro general-purpose port VDDIO 3.3V power supply YSUSA_0 Y-Drive control signal output YSUSA_6 Y-Drive control signal output YSUSA_12 Y-Drive control signal output YSUSB_0 Y-Drive control signal output VDDD33 3.3V power supply PDP-5050SX...
Page 186
3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply VDDLA 3.3V power supply PDP-5050SX...
Page 187
B phase signal input of G video (ninth bit) GBI_5 B phase signal input of G video (fifth bit) BBI_9 B phase signal input of B video (ninth bit) BBI_3 B phase signal input of B video (tenth bit) PDP-5050SX...
Page 188
VSSLA AB21 VSSLA AB22 VSSLA AA22 VDDLA 3.3V power supply VSSL15 VSSLA VSSLA VSSL15 SDITMS JTAG signal GPIO0_5 Microcomputer macro general-purpose port VSS15 YSUSA_2 Y-Drive control signal output YSUSA_8 Y-Drive control signal output VSSD15 YSUSB_2 Y-Drive control signal output PDP-5050SX...
Page 189
VDDLA 3.3V power supply AA13 VDDLA 3.3V power supply AA14 VDDLA 3.3V power supply AA15 VDDLA 3.3V power supply AA16 VDDL15 1.5V power supply AA17 VDDLA 3.3V power supply AA18 VDDLA 3.3V power supply AA19 VDDL15 1.5V power supply PDP-5050SX...
Page 190
B phase signal input of R video (first bit) VDD15 1.5V power supply GBI_3 B phase signal input of G video (third bit) BBI_7 B phase signal input of B video (seventh bit) BBI_1 B phase signal input of B video (first bit) VDD15 1.5V power supply PDP-5050SX...
Page 192
MIDSCV Internal middle scale voltage bias CLAMP Clamp input (External clamp signal) − Analog power supply (3.3V) − Ground − Ground − Analog power supply (3.3V) BAIN Analog input for converter B − Ground − Analog power supply (3.3V) PDP-5050SX...
Page 193
RED 5 Converter Red output RED 4 Converter Red output RED 3 Converter Red output RED 2 Converter Red output RED 1 Converter Red output RED 0 Converter Red output − Power supply (3.3V) − Power supply (3.3V) − Ground PDP-5050SX...
Page 195
Analog 5V supply Analog RINA or YINA signal input. Sync signal is input on SYNCIN pin. GSR1 ROUT/YOUT output buffer gain set input Analog RINB or YINB signal input. Sync signal is input on SYNCIN pin. − (NC) No connection PDP-5050SX...
Page 196
Block Diagram HSCTL POLH H SYNC DET. C / HSYNC IN EXIH VIDEO IN POLV SYNC SEPA. VSEPA EXIV HOR. SYNC CONTROL V SYNC SEPA. VSYNC IN CVPOL HDRV V SYNC DET. CVEXI CLAMP CPSEL VDRV CLAMP PULSE GEN. CPWID PDP-5050SX...
Page 197
Indecates whether the vertical synchronization signal exists. Vertical polarity output POLV Indicates the polarity of the vertical synchronization signal. Horizontal existence output EXIH Indicates whether the horizontal synchronization signal exists. Horizontal polarity output POLH Indicates the polarity of the horizontal synchronization signal. PDP-5050SX...
Page 198
83,84 RXC± BOARD MASK CONTROL PANEL LINK SPDIF 86,87 RX0± TMDS CONTROL SIGNALS DIGITAL CORE VIDEO RX1± 91,92 COLOR HSYNC CONTROL SIGNALS RX2± 96,97 SPACE VSYNC CONVERTER ODCK UP/DOWN SAMPLING 36-39,42-44,48-55, Q[23-0] 58-63,68-70 AnGY VIDEO AnRPr AnBPb RSET COMP PDP-5050SX...
Page 199
OVCC Output bus power supply (3.3V) RX2+ TMDS data input − 24-bit output pixel data bus AGND Analog ground − 24-bit output pixel data bus Digital ground − 24-bit output pixel data bus 100 VCC Digital power supply (3.3V) PDP-5050SX...
Page 200
34 DQ18 Burst 36 DQ19 Counter 37 DQ20 39 DQ21 40 DQ22 42 DQ23 45 DQ24 47 DQ25 48 DQ26 50 DQ27 CAS Latency Pipe Line Control Mode Register Data Out Control 51 DQ28 53 DQ29 54 DQ30 56 DQ31 PDP-5050SX...
Page 201
I/O Data input/output DQ13 I/O Data input/output DQ22 I/O Data input/output DQ14 I/O Data input/output − − VDDQ Power supply for output buffer VSSQ Ground for output buffer DQ23 I/O Data input/output DQ15 I/O Data input/output − − Power supply Ground PDP-5050SX...
Page 202
Write enable DW/W 16 bit, 32 bit mode switch Write protect Acceleration − 17, 27, 33, 64, 74, 79 V Ground − 12, 18, 28, 58, 63, 73 V Power supply 1-5, 41-50, − N.C. No connection 83-85, 89, 90 PDP-5050SX...
Page 203
CONFIGURATION ENGINE EEPROM LOGIC BLOCK HSYNC VSYNC EXT_SWING IDCK+ IDVK- 21,22 TXC± PANEL LINK 24,25 TX0± ENCRYPTED TMDS 36-47, DATA CLEAR DATA 27,28 TX1± DIGITAL CORE 50-55, DATA CAPTURE MASK D[23-0] 58-63 LOGIC BLOCK 30,31 TX2± CONTROL SIGNALS CTL3 PDP-5050SX...
Page 204
24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input 24-bit pixel bus input PDP-5050SX...
Page 205
24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input − Digital ground PDP-5050SX...
Page 207
Data input/output Data input/output − VSSQ Ground for DQ DQ10 Data input/output DQ11 Data input/output − VDDQ Power supply for DQ DQ12 Data input/output DQ13 Data input/output − VSSQ Ground for DQ DQ14 Data input/output DQ15 Data input/output − Ground PDP-5050SX...
Page 212
4 : 3 letter-box signal at 1.3 V or more to 2.5 V or less S2-3 16 : 9 picture squeezed signal at 2.5 V or more S2-4 This pin is pulled down to GND by a 100 k ohm resistor, so the 4 : 3 video signal is selected when open. PDP-5050SX...
Page 213
Connects trap circuit for subcarrier. TRAP2 Audio signal output mute. Mute OFF at 1.5 V or less − MUTE Mute ON at 2.5 V or more Mute OFF when open. Internal reference bias (VCC/2). − BIAS Connect to GND via a capacitor. PDP-5050SX...
Page 214
BIAS OVER VOLTAGE / CIRCUIT SURGE PROTECTOR V CC THERMAL STANDBY OUTPUT PIN TO GND SHUT DOWN SHORT PROTECTOR PREDRIVER POWER LOAD SHORT POWER PROTECTOR GND2 PREDRIVER POWER OUTPUT PIN TO V CC SHORT PROTECTOR POP NOISE PREVENTION CIRCUIT PDP-5050SX...
19 INPUT 1 terminal (S-VIDEO) 9 INPUT 1 terminals 20 INPUT 4 terminals (AUDIO) (COMPONENT VIDEO: Y, C 21 INPUT 4 terminals 10 INPUT 3 terminals (AUDIO) (COMPONENT VIDEO: Y, C 11 CONTROL OUT terminal 22 HDMI terminal (INPUT3) PDP-5050SX...
Page 216
• If the remote control unit is left in total darkness for a long period of time, it will not emit light, but will not be damaged. In this case, place it in a bright place for a little while before using it. PDP-5050SX...
Page 217
• A table or an area of the floor with adequate strength installing to ensure ventilation around the backside. should always be used to support the Plasma Display. Using the optional PIONEER stand Failure to do so could result in personal injury and physical damage.