Table of Contents
Advertisement
6
Table 3: DKHiQV-PCI board (Rev. A) Configuration Settings for B65555,
Jumper
Function*
W1
sh.2, STANDBY
W2
sh.5, TV out
W3
sh.2, 14MHz
W4
sh.5, TV out
W5
sh.2, TV out
W6
sh.5, TV out
W7
sh.5, DDC pull up
W8
sh.2, TV out
W9
sh.2, GVCC
W10
sh.3, PCI
W11
sh.3, PCI
W12
sh.5, VEESAFE
W13
sh.5, VEESAFE
W14
sh.5, VEESAFE
W15
sh.5,VDDSAFE
W16
sh.5,VDDSAFE
W17
sh.5,VDDSAFE
W18
sh.5, +12SAVE
W19
sh.5, +12SAVE
W20
sh.5, +12SAVE
W21
sh.5, VEESAFE
W23
sh.4, 3VREG2
W24
sh.4, PVCC/SVCC
W25
sh.4, PVCC/SVCC
W26
sh.4, OCSVCC
W27
sh.4, AVCC55X
W28
sh.4, IVCC55X
W29
sh.4, IVCC55X
W30
sh.4, DVCC55X
W31
sh.4, MVCC55X
W32
sh.4, RAMVCC
Notes: *Schematic reference and functional
category
**'on' - jumper plug is installed
'off' - jumper plug is not installed
1. Set potentiometer R59 for panel requirements.
2. Set potentiometer R75 for 3.3V on W24, pin 3.
3. Set potentiometer R76 for 3.3V on W25, pin 3.
4. Set potentiometer R82 for panel requirements.
&+,36
®
ABHiQV (Fab Rev. C)
User's Guide
TV out and multimedia disabled
Note: Refer to Figure 3 for jumper locations.
State**
Jumper
off
off
off
1-2
1-2
off
2-3
off
2-3
on
off
off
off
on
on
off
off
off
on
off
All off
off
2-3
2-3
1-2
2-3
2-3
2-3
2-3
2-3
2-3
Subject to Change Without Notice
Function*
W33
sh.4, BVCC55X
W34
sh.4, XVCC55X
W35
sh.4, 3VMAIN
W36
sh.2, CVCC
W37
sh.5, M/PCLK
W38
sh.5, Panel V
DD
W39
sh.5, VEESAFE by R82
W40
sh.2, interrupt
JP1
sh.5, CRTdrive
JP2
sh.5, CRTdrive
JP3
sh.5, CRTdrive
JP4
sh.5, Panel V
CC
JP5
sh.2, I2C
JP6
sh.2, I2C
JP7
sh.2, DDC
JP8
sh.2, DDC
JP9
sh.2, GPIO
JP10
sh.2, GPIO
JP11
sh.2, GPIO
JP12
sh.2, GPIO
JP13
sh.2, CSYNC/HSYNC
JP15
sh.2, P34
JP16
sh.2, P35
JP17
sh.2, P32
JP18
sh.2, P30
JP19
sh.2, P33
JP20
sh.2, P31
R59
sh.5, VEESAFE
R75
sh.4, 3VREG2
R76
sh.4, 3VMAIN
R82
sh. 5, VEESAFE
Revision 1.1
State**
2-3
2-3
1-2
1-2
2-3
2-3
off
on
off
off
off
off
All off
All off
1-2 & 3-4
All off
All off
1-4 & 2-3
1-4 & 2-3
3-4
off
on
on
on
on
on
on
Note (1)
Note (2)
Note (3)
Note (4)
7/15/98
Advertisement
Table of Contents
