Table of Contents
Advertisement
4
Table 1: DKHiQV-PCI (Rev. A) Board Configuration Settings For B69000,
Note: Refer to Figure 3 for jumper locations.
Jumper
Function*
W1
sh.2, STANDBY
W2
sh.5, TV out
W3
sh.2, 14MHz
W4
sh.5, TV out
W5
sh.2, TV out
W6
sh.5, TV out
W7
sh.5, DDC pull up
W8
sh.2, TV out
W9
sh.2, GVCC
W10
sh.3, PCI
W11
sh.3, PCI
W12
sh.5, VEESAFE
W13
sh.5, VEESAFE
W14
sh.5, VEESAFE
W15
sh.5,VDDSAFE
W16
sh.5,VDDSAFE
W17
sh.5,VDDSAFE
W18
sh.5, +12SAVE
W19
sh.5, +12SAVE
W20
sh.5, +12SAVE
W21
sh.5, VEESAFE
W23
sh.4, 3VREG2
W24
sh.4, PVCC/SVCC
W25
sh.4, PVCC/SVCC
W26
sh.4, OCSVCC
W27
sh.4, AVCC55X
W28
sh.4, IVCC55X
W29
sh.4, IVCC55X
W30
sh.4, DVCC55X
W31
sh.4, MVCC55X
W32
sh.4, RAMVCC
Notes: *Schematic reference and functional category
**'on' - jumper plug is installed
'off' - jumper plug is not installed
1. Set potentiometer R59 for panel requirements.
2. Set potentiometer R75 for 3.3V on W24, pin 3.
3. Set potentiometer R76 for 3.3V on W25, pin 3.
4. Set potentiometer R82 for panel requirements.
&+,36
®
ABHiQV (Fab Rev. C)
User's Guide
TV Out And Multimedia Disabled
State**
Jumper
off
W33
off
W34
off
W35
1-2
W36
1-2
W37
off
W38
2-3
W39
off
W40
2-3
JP1
on
JP2
off
JP3
off
JP4
off
JP5
on
JP6
on
JP7
off
JP8
off
JP9
off
JP10
on
JP11
off
JP12
all off
JP13
off
JP15
2-3
JP16
2-3
JP17
1-2
JP18
2-3
JP19
2-3
JP20
2-3
R59
2-3
R75
2-3
R76
2-3
R82
Subject to Change Without Notice
Function*
sh.4, BVCC55X
sh.4, XVCC55X
sh.4, 3VMAIN
sh.2, CVCC
sh.5, M/PCLK
sh.5, Panel V
DD
sh.5, VEESAFE by R82
sh.2, int #
sh.5, CRTdrive
sh.5, CRTdrive
sh.5, CRTdrive
sh.5, Panel VCC
sh.2, I2C
sh.2, I2C
sh.2, DDC
sh.2, DDC
sh.2, GPIO
sh.2, GPIO
sh.2, GPIO
sh.2, GPIO
sh.2, CSYNC/HSYNC
sh.2, P34
sh.2, P35
sh.2, P32
sh.2, P30
sh.2, P33
sh.2, P31
sh.5, VEESAFE
sh.4, 3VREG2
sh.4, 3VMAIN
sh. 5, VEESAFE
Revision 1.1
State**
2-3
2-3
1-2
1-2
2-3
2-3
off
on
off
off
off
off
All off
All off
1-2 & 3-4
All off
All off
1-4 & 2-3
1-4 & 2-3
3-4
off
on
on
on
on
on
on
Note (1)
Note (2)
Note (3)
Note (4)
7/15/98
Advertisement
Table of Contents
