Related Manuals for E+E Elektronik EE160
Summary of Contents for E+E Elektronik EE160
- Page 1 User Manual EE160 Humidity and Temperature Sensor for HVAC Applications BA_EE160 // v2.0 // Modification rights reserved...
- Page 2 E+E Elektronik Ges.m.b.H. does not accept warranty and liability claims neither upon this publication nor in case of improper treatment of the described products. The document may contain technical inaccuracies and typographical errors. The content will be revised on a regular basis.
-
Page 3: Table Of Contents
CONTENT General ..............................4 Explanation of Symbols ..........................4 Safety Instructions ............................4 1.2.1 General Safety Instructions ..........................4 1.2.2 Intended Use ................................4 1.2.3 Mounting, Start-up and Operation ........................5 Environmental Aspects ..........................5 Scope of Supply ..........................5 Product Description ..........................6 General ................................6 Dimensions ..............................6 Electrical Connection .............................6 Setup and Adjustment ........................7 EE-PCS Product Configuration Software ......................8... -
Page 4: General
The EE160 is intended for the humidity (RH) and temperature (T) measurement in HVAC applications. The use of the EE160 in any other way than described in this manual bears a safety risk for people and the entire measurement installation and is therefore not allowed. The manufacturer cannot be hold responsible for damages as a result of incorrect handling, installation, and maintenance of the equipment. -
Page 5: Mounting, Start-Up And Operation
1.2.3 Mounting, Start-up and Operation The EE160 humidity and temperature sensor has been produced under state of the art manufacturing conditions, has been thoroughly tested and has left the factory after fulfilling all safety criteria. The manufacturer has taken all precautions to ensure safe operation of the device. The user must ensure that the device is set up and installed in a manner that does not have a negative effect on its safe use. -
Page 6: General
General The EE160 probe is optimized for cost effective, accurate measurement of relative humidity (RH) and temperature (T) in building automation. The measured data is available on two voltage or current (2-wire) outputs ƒ the RS485 interface with BACnet MS/TP or Modbus RTU protocol ƒ... -
Page 7: Setup And Adjustment
EE160 and PC Setup and Adjustment The EE160 is ready to use and does not require any configuration by the user. The factory setup of EE160 corresponds to the type number ordered. Please refer to the data sheet at www.epluse.com/ EE160. -
Page 8: Ee-Pcs Product Configuration Software
1. Download the EE-PCS Product Configuration Software from www.epluse.com/configurator install it on the PC. 2. Connect the EE160 to the PC using the USB configuration adapter or the EEE-PCA product configuration adapter, respectively. 3. Start the EE-PCS software. 4. Follow the instructions on the EE-PCS opening page for scanning the ports and identifying the connected device. -
Page 9: Bacnet Setup
Slave ID (Modbus address) 0x00 Modbus protocol settings 0x01 1) Register number starts from 1. 2) Protocol address starts from 0. 3) For Modbus protocol settings see Application Note Modbus AN0103 (available at www.epluse.com/EE160). INFO (read register) Parameter Register number [DEC] Protocol address... -
Page 10: Modbus Register Map
2) Register address starts from 0. 3) The choice of measurement units (metric or non-metric) is done at the time of ordering, see the ordering guide in the EE160 data sheet. It is not possible to switch from metric to non-metric or vice versa by means of the EE-PCS. -
Page 11: Rh / T Adjustment And Calibration
Calibration and adjustment at E+E Elektronik ƒ Calibration and/or adjustment can be performed in the E+E Elektronik calibration laboratory. For information on the E+E capabilities in ISO or accredited calibration please see www.eplusecal.com. Calibration and adjustment by the user ƒ... -
Page 12: Technical Data
The accuracy statement includes the uncertainty of the factory calibration with an enhancement factor k=2 (2-times standard deviation). The accuracy was calculated in accordance with EA-4/02 and with regard to GUM (Guide to the Expression of Uncertainty in Measurement). User Manual EE160 Humidity and Temperature Sensor for HVAC Applications... - Page 13 HEADQUARTERS SUBSIDIARIES E+E Elektronik Ges.m.b.H. E+E Elektronik China E+E Elektronik Germany E+E Elektronik Korea Langwiesen 7 18F, Kaidi Financial Building, Schöne Aussicht 8 C Suite 2001, Heungdeok IT 4209 Engerwitzdorf No.1088 XiangYin Road 61348 Bad Homburg Valley Towerdong, 13, Austria 200433 Shanghai Tel.:...