SAFETY WARNING! NEVER operate the unit unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating.
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later.
SECTION I INTRODUCTION AND DESCRIPTION 1-1 Introduction 23HP, 32HP Vanguard & 26HP Briggs ELS - Add (2) flat washers P#(K0131) between clutch and pump pulley, use (1) 7/16”-20 x 4” HHCS P#(K0359) and We are pleased to have you as a Bad Boy customer. Your collection system has been designed to give you a (1) 7/16”...
2-3 Belt Installation 2-2 PTO Assembly Installation Remove the pulley guard P#(B0075) by removing the (2) Remove the (2) existing nuts and bolts that secure the 1/4”-20 x ½” HHSTS P#(K0353), see page 9, diagram # rear guard to the rear frame of the mower. Remove 38 and #39 for part location.
Cam Assembly Figure 2-4 Figure 2-6 Secure Exhaust Tension Deflector To Muffler Cam Stop 2-7 Mount Tube Stiffener and Debris Bolt Shield Installation Place the lower mount tube stiffener P#(B0247) between 2-5 Lower Frame Installation the lower mount tube and the rear guard as shown in Figure 2-7.
Exploded Parts View A1157 Top Assembly Item # Doc # Title V0022 PRO 3 BAGGER TOP B0676 Hinge Stop Pl. K0114 BLACK PLASTIC RIVET C0069 DUST GUARD BRACE K1030 1/4"-20 x 1-1/4" CARRIAGE BOLT J4009 SHORT RUBBER STRAP W/ S HOOK K0037 1/4"...
Page 9
Exploded Parts View Exploded View Of The A0610 - PTO Assembly Item Document Title Quantity Item Document Title Quantity Item Document Title Quantity Number Number Number Number Number Number A0593 PTO ARM ASSY. K0086 .125 OD x 2.50 HAIR PIN CLIP M0228 BLOWER PULLEY A0429...
2-10 Boot To Mower Deck Installation 2-8 Upper Frame Assembly 60” Boot Plate Mounting Instructions Installation To mount the boot plate P#(B0184) to the boot NOTE: During this step, it is suggested that two people P#(E1113) use (2) 3/8”-16 x 1” carriage bolts P#(K1182) install the upper frame to the lower mount tube.
2-11 Blower Cone Installation 2-12 Impeller Blade Removal/Replacement Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially To Remove: First remove the 3/8”-16 x 1-1/2” HHCS thread the bolts into each of the two tabs located on the P#(K1211) (#1), taper lock bushing washer P#(K0278) blower housing.
2-13 Lengths Of Hose Adjustment 2-15 Lower Hose To Blower Cone Installation The hoses in steps 2-14 and 2-15 must be cut to fit your machine. Follow steps 2-14 and 2-15. Do not cut the Slide a 8” hose clamp P#(J0080) over both ends of the hoses until you have tried to fit them on your machine.
2-18 Installation/Removal Of Figure 2-18b Plastic Top Collection Bags To install the bag onto the bag ring, first make sure the bag ring end caps are fastened to the bag ring. Place the seam openings of the bag onto the bag ring openings and turn the bag until the slot bracket in the bag ring is protruding from the opening in the bag (Figure 2-18a).
SECTION III 3-3 Disengagement Of The Blower OPERATING A. To disengage the blower, rotate the engagement INSTRUCTIONS handle towards the mower. 3-1 General Safety WARNING: The blower will continue to spin. DO NOT TOUCH the blower, pulleys, or the belt until the tractor is Only qualified people familiar with this operator’s manual turned off.
SAFETY DECALS To promote safe operation, Bad Boy supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part # R1051 Part #: R1054 Part #: R1057 Part #: R1065 Part #: R1050...
Page 20
Turn any Bad Boy Lawn Vac into a total lawn grooming tool with the Bad Boy Wand Kit! With your Bad Boy Wand Attachment you will double the ability of your Bad Boy Lawn Vac. Using the same powerful vacuum/blower that makes your Lawn Vac work so well, you will be able to get to all those hard-to-reach places where you needed a rake or broom before.