Page 1
GilAir5 battery packs. See Labeling for intrinsic safety approvals. Pat. Pending Made In USA ® Gilian 16333 Bay Vista Dr. • Clearwater, Florida 33760 • (800) 451-9444 • (727) 530-3602 • (727) 539-0550 [FAX] • www.sensidyne.com Revision E • Document No. 800880M...
Page 2
LETTER FROM THE PRESIDENT Thank you for purchasing your new Sensidyne air monitoring product. We stand behind all of the products we sell . . . each Sensidyne product has been designed and manufactured to provide unparalleled service, day after day. Our professional staff has tested each unit under the strictest conditions possible to ensure successful, accurate results every time.
Gilian ® GILAIR-3 & GILAIR-5 AIR SAMPLING SYSTEMS PACKING LIST The items listed below are shipped the Gilian GilAir-3/GilAir-5 Air Sampling System: • GilAir-3 or GilAir-5 Air Sampling Pump • Tool Kit • Tubing • Air Boss • Restrictor •...
Page 4
PROPRIETARY NOTICE This manual was prepared exclusively for the owner of the Sensidyne GilAir Air Sampling System. The material within this manual is proprietary information and is to be used only to understand, operate, and service the instrument. By receiving...
Setting The Pump Flow Rate ................. 19 2.3.4 Sample Gathering ..................19 2.3.5 HOLD (Pause) Feature .................. 19 2.3.6 Sampling Run Termination & Recovery ............19 2.3.7 Display Self-Test .................... 19 2.3.8 Programming The Pump ................20 Sensidyne Document No. 800880M (Rev E)
Page 6
Battery Life ..................... 23 4.1.2 Memory Effect ....................23 4.1.3 Leakage Current .....................23 Charging Systems ..................... 24 4.2.1 Single Station Charger..................24 4.2.2 Universal Multi-Station Charger..............24 4.2.3 BMS Multi-Station charger ................24 — PRELIMINARY — Sensidyne Document No. 800880M (Rev E)
Page 7
GilAir-5 Air Sampler (Front View) ................13 Display: Clock Timer Model ................... 16 Display: Program Timer Model ................18 LIST OF TABLES Available GilAir-3 & GilAir-5 Models ................ 9 Pneumatic System ....................10 Estimated Battery Life ....................23 Sensidyne Document No. 800880M (Rev E)
DO NOT drop, crush, or roughly handle the unit, and NEVER submerge the unit in water. This can cause pump failure or faulting. DO NOT run the pump beyond its recommended specifications. — PRELIMINARY — Sensidyne Document No. 800880M (Rev E)
User-defined program. erance envelope during the run. The number is located “P3” User-defined program. on the bottom right portion of the display. “P4” User-defined program. “P5” User-defined program. “P6” User-defined program. “E” Programming error. Sensidyne Document No. 800880M (Rev E)
Use only with Gilian battery pack PN 800464 or 800464-1. Made in USA BATTERY PACK Flow Adj. FLOW ADJUST CONTROL POWER SWITCH Subs pack Figure 1.1 GilAir-3 Air Sampler (Front view) — PRELIMINARY — Sensidyne Document No. 800880M (Rev E)
Use only specified GilAir5 battery packs. See Labeling for intrinsic safety approvals. Pat. Pending Made In USA ® Gilian BATTERY PACK Flow Adj. FLOW ADJUST CONTROL POWER SWITCH Figure 1.2 GilAir-5 Air Sampler (Front view) Sensidyne Document No. 800880M (Rev E)
This Pull Start Jack may only be used as an ON/OFF sentation of up to 9%. Across the lower portion of switch. Charging must be done through the original the display may be presented one or more icons. charging socket. — PRELIMINARY — Sensidyne Document No. 800880M (Rev E)
(see Section 2.3.8). Exception: If “CAL” is showing on the display the pump is in calibration mode and no data will be collected at this time. Sensidyne Document No. 800880M (Rev E)
1 second. The pump will stop and a “Hand” symbol will appear flashing in the display window. 2. The sampling run can be resumed by pressing the MODE/HOLD button again. The “Hand” icon will be removed from the display window. Sensidyne Document No. 800880M (Rev E)
Cycle Count pro- decrement the value, respectively. gramming mode with a flashing “E” in the small digit area, until a value for Cycle Count is acceptable when the PROG button is pressed. — PRELIMINARY — Sensidyne Document No. 800880M (Rev E)
The unique feature of this system is that it will automatically shut the flow off when the bag has been filled. The maximum pressure within the bag is ap- proximately 8” of water. Sensidyne Document No. 800880M (Rev E)
A Gilibrator 2 or conventional bubble flow meter is preferable since the pressure drop through this type of device is negligible. — PRELIMINARY — Sensidyne Document No. 800880M (Rev E)
This process can be repeated two or three times without causing signs of memory effect. – 0 1 – – 0 2 – < Table 4.1 Estimated Battery Life Sensidyne Document No. 800880M (Rev E)
Overcharging in this mode can cause overheating, which shortens battery life. • Pulsed Charge This charging feature is used to temporarily maintain full capacity of the battery. — PRELIMINARY — Sensidyne Document No. 800880M (Rev E)
, t i , " " 4 , " " 8 " 4 , " " 8 For further information on Gilian spare parts, please contact your Sensidyne Customer Service Representative at 800-451-9444, ext 782. Sensidyne Document No. 800880M (Rev E)
Gilian has developed several programs which will allow you to select just the right options best suited to your applications and needs. For further information, contact the Gilian Service Department. — PRELIMINARY — Sensidyne Document No. 800880M (Rev E)
Page 30
16333 Bay Vista Dr. • Clearwater, Florida 33760 • (800) 451-9444 • (727) 530-3602 • (727) 539-0550 [FAX] • www.sensidyne.com...
Need help?
Do you have a question about the Gilian GILAIR-3 and is the answer not in the manual?
Questions and answers
Why won't my Gilair3 get to the proper air flow range?