Subscribe to Our Youtube Channel
Related Manuals for Teldat Connect-4GE
Summary of Contents for Teldat Connect-4GE
- Page 1 Manual Teldat S.A. Teldat Connect-4GE Router Teldat Dm591-I Copyright© Version 2.3 Teldat S.A. Teldat Connect-4GE Router...
- Page 2 This publication is subject to change. Teldat S.A. offers no warranty whatsoever for information contained in this manual. Teldat S.A. is not liable for any direct, indirect, collateral, consequential or any other damage connected to the deliv- ery, supply or use of this manual.
-
Page 3: Table Of Contents
Chapter 2 Teldat Connect-4GE Router ......3 Characteristics ........ - Page 4 Dimensions and weight ....... . B.4.7 Environmental Specifications ......Teldat Connect-4GE Router...
-
Page 5: About This Guide
1 About This Guide Teldat S.A. Chapter 1 About This Guide This is the installation guide for the Teldat Connect-4GE router and contains information on how to correctly install this device in a working environment. 1.1 Supported Devices The information contained in this installation guide only applies to the Teldat Connect-4GE router. -
Page 6: Related Documentation
1 About This Guide Teldat S.A. Fax: +34 918 076 566 Email: support@teldat.com 1.8 Related documentation Dm748-I Software Updating. Teldat Connect-4GE Router... -
Page 7: Teldat Connect-4Ge Router
Chapter 2 Teldat Connect-4GE Router 2.1 Characteristics 2.1.1 Power Supply For further information on the power supply for the Teldat Connect-4GE, please see the chapter on “Components and power supplies” , in the section on “Power Supply” . 2.1.2 Hardware Monitoring The Teldat Connect-4GE router hardware is monitored through the LEDs panel. -
Page 8: Components And Power Supply
3 Components and Power Supply Teldat S.A. Chapter 3 Components and Power Supply The following chapter provides detailed information on the chassis of the Teldat Connect-4GE router and its compon- ents. This information includes: • Components. • Information on assembly. -
Page 9: Side Panels
Two WWAN antennas are located on the side panels, one on either side. Fig. 3: Right hand side panel Fig. 4: Left hand side panel 3.1.4 Underside Panel The following elements can be found on the underside panel: Teldat Connect-4GE Router... -
Page 10: Top Panel (Leds)
The LED panel provides information on the state of the components (whether they are active or not) and on network activity. Fig. 6: LED Panel The Teldat Connect-4GE LEDs are shown in Figure 6. The following table contains a description: LEDs table Status... -
Page 11: Assembly
Green -> connected. Blinking: connection data activity. 3.2 Assembly 3.2.1 Mounting in rack The Teldat Connect-4GE cannot be mounted in a rack. However, there are other types of mounting. 3.2.2 Standalone The Teldat Connect-4GE can be placed as a standalone on a flat, stable surface. - Page 12 The screws must go into a wall stud (wood) or a wall anchor of the appropriate type for the wall. Screws into drywall are not strong enough to mount the router. Fig. 9: Wall-mounting features on the Teldat Connect-4GE router The above figure shows the wall-mounting features on the Teldat Connect-4GE router. Wall screws 8,8 cm (3.46 inches)
-
Page 13: Installing A Din Rail Mount Accessory (Optional)
The kit contains 2 screws to adjust the rail accessory on the underside of the device, as shown in Figure 10. Fig. 10: DIN rail mount adapter 3.3 Power Source The Teldat Connect-4GE is powered though an external AC/DC source or through an Ethernet cable (provided it complies with the POE 802.3af standard). Warning The equipment must be used with the power supply provided by the manufacturer, or equivalent. -
Page 14: Poe
3.3.2 PoE Fig. 11: Diagram to connect the PoE adapter to the router The Teldat Connect-4GE can be powered through an Ethernet cable, provided it complies with the POE 802.3aF standard. The ETHERNET port is enabled for this. To connect the Ethernet cable with PoE power to the router, please carry out the steps included in the... -
Page 15: Disconnect
The router’s default configuration sets the following IP address and access mask: • IP address: 192.168.1.1 • IP mask: 255.255.255.0 Note Some devices leave the factory with personalized settings. As a result of this customization, the default configuration may be different from the one shown above. Teldat Connect-4GE Router... -
Page 16: Connecting Data
Installing these antennas in the Teldat Connect-4GE is essential when it comes to improving the quality of the signal received and transmitted by the cellular model. -
Page 17: Installing The Sim Card
3.6 Installing the SIM card For the WWAN interface to operate correctly, a SIM card must be inserted in the Teldat Connect-4GE. The router is equipped with an external SIM card tray. When inserting the SIM card, make sure you are protected against electrostatic discharges (ESD). - Page 18 3 Components and Power Supply Teldat S.A. • Then press it until it is totally inserted. • To extract it, press it again and remove it. Teldat Connect-4GE Router...
-
Page 19: Appendix A Safety Information
Safety information Teldat S.A. Appendix A Safety information A.1 Translated Safety Warnings Connect Disconnect Teldat Connect-4GE Router... -
Page 20: Psu Energy Efficiency
Input Voltage 100-240 Vac Input AC frequency 50-60 Hz Output voltage 12.0 V Output current 1.0 A Output power 12,0 W Average active efficiency 88.6 % Efficiency at low load (10%) 73.8 % No-load power consumption 0.09 W Teldat Connect-4GE Router... -
Page 21: Troubleshooting
FTP purposes. B.2 Updating the software The Teldat Connect-4GE router can be updated to new releases. Please ask your distributor for further details on new releases. Firmware updating is carried out through a traditional FTP file transfer. For further information on updating firmware through FTP, please see manual Dm748-I Software Updating, section 1.3 FTP Updating. -
Page 22: Connectors
RF in/out External B.3.3 Power Supply Connector Power Supply Connector PINOUT Internal POSITIVE External NEGATIVE B.4 Technical Specifications B.4.1 Hardware Architecture PROCESSORS Freescale P1014. MEMORY DDR3 1Gbit (128 MByte). STORAGE UNIT FLASH Memory 128 Mbits (16 Mbytes). Teldat Connect-4GE Router... -
Page 23: Lan Interface
B.4.5 External Power Supply INPUT VOLTAGE 100-240V AC. INPUT CURRENT 1.0 A. INPUT FREQUENCY 50-60 Hz. B.4.6 Dimensions and weight TYPE Desktop or wall mounted. LENGTH x WIDTH x HEIGHT 145 x 160 x 50 mm. WEIGHT 0.3 Kg. Teldat Connect-4GE Router... -
Page 24: Environmental Specifications
Appendix B Teldat S.A. B.4.7 Environmental Specifications TEMPERATURE OPERATING NORMALLY: 0ºC to 45ºC STORED: -25ºC to 70ºC RELATIVE HUMIDITY On: 5% to 90% Teldat Connect-4GE Router...
Need help?
Do you have a question about the Connect-4GE and is the answer not in the manual?
Questions and answers