Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SIIG AV-GM04R3-S1-TX
Summary of Contents for SIIG AV-GM04R3-S1-TX
- Page 1 HDMI over IP Multicast System P/N: AV-GM04R3-S1...
-
Page 2: Table Of Contents
Safety and Notice The AV-GM04R3-S1 HDMI over IP Multicast System has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the AV-GM04R3-S1 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. -
Page 3: Introduction
● Latency: 720P60: 190~240ms / 1080P60: 380~430ms. ● Wall mounting housing design for easy and robust installation PACKAGE CONTENTS AV-GM04R3-S1-TX AV-GM04R3-S1-RX ● 1x AV-GM04R3-S1-TX ● 1x AV-GM04R3-S1-RX ● 1x IR blaster cable ● 1x IR receiver cable ● 1x 5V2A Power adapter ●... -
Page 4: Specifications
SPECIFICATIONS Model Name AV-GM04R3-S1 Technical AV-GM04R3-S1 [Tx] AV-GM04R3-S1 [Rx] Role of usage Transmitter [TX] Receiver [RX] HDMI compliance V1.3 HDCP compliance Video bandwidth Single-link 225MHz [6.75Gbps] Video support Up to 1080p60 HDMI over UTP Full HD (1080p)-100m(330ft) [CAT.X] transmission [24-bit] Audio support stereo digital audio Input TMDS signal... - Page 5 Relative humidity 20~90% RH [no condensation]...
-
Page 6: Panel Descriptions
PANEL DESCRIPTIONS Transmitting unit ► AV-GM04R3-S1-TX Front Panel +5V DC: Connect to 5V DC power supply Mini USB: for F/W update S/PDIF Output (TOSLINK) Stereo Output (3.5mm) HDMI IN: Connects to a HDMI source with a HDMI male-male cable Rear Panel IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster... -
Page 7: Receiving Unit
Receiving unit ► AV-GM04R3-S1-RX Front Panel +5V DC: Connect to 5V DC power supply Mini USB: for F/W update HDMI OUT: Connect to a HDMI display with a HDMI male-male cable. Rear Panel IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver LED Indicator: Power LED indicator Dip Switch: Video channel setting (Please refer to “Notes”) HDMI Signal IN: RJ-45 Network connector... - Page 8 Notes: TX group ID dip-switch setting 1. For ID=1~63, please refer the table below to set up (Hardware control) 2. For ID=64~1023, please adjust the DIP switch to ID=0, and the real ID can be decided by the external software (Software control) ID Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 ID Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 ↓...
-
Page 9: Connection Diagram
CONNECTION DIAGRAM... -
Page 10: Ir Pass-Through
IR PASS-THROUGH IR Extenders IR Blaster IR Receiver IR Sockets IR BLASTER: plug in the IR blaster to emit all IR command signals received from the IR receiver from the other enf to control the devices corresponding to the IR signals. IR RECEIVER: plug in the IR receiver to receive all IR command signals from the IR remote controls of the corresponding devices. - Page 11 You can buy any IR extension cables in the market that are compatible to the definition of the IR sockets for the extender if necessary for replacement use. However, IR cables longer than 2m (6-ft) may not work.
-
Page 12: Warranty
Also, the technical information contained herein regarding the AV-GM04R3-S1 features and specifications is subject to change without further notice. Support For more info or tech support http://www.siig.com/support April, 2018...
Need help?
Do you have a question about the AV-GM04R3-S1-TX and is the answer not in the manual?
Questions and answers