HELIOTERM INVERTER
CBD 35 - PAINEL DE COMANDO A BORDO (TOP)
Avisos preliminares
Estas instruções são parte integrante do manual do aparelho
no qual o KIT é instalado. Consulte este manual para as
ADVERTÊNCIAS GERAIS e REGRAS FUNDAMENTAIS DE SEGURANÇA.
Em algumas partes do manual são utilizados os símbolos:
ATENÇÃO = para ações que exigem cautela especial
e preparação adequada.
PROIBIDO
=
para
absolutamente ser executadas.
Versões
Códigos
20116408
CBD 35 - Painel de comando a bordo (TOP)
Montagem, configuração e ligações dos
painéis de comando a bordo da máquina
O comando executa a função de temperatura mínima da
água no inverno (30 °C) e temperatura máxima no verão
(20 °C), possui contactos limpos independentes para o
comando de um refrigerador, de uma caldeira e de uma
entrada do contacto de presença.
Possui uma saída de 230 V para o comando da eletroválvula
de verão e inverno.
Montagem
Insira o painel de controlo na respetiva sede, na parte
superior do aparelho e fixe-o com os dois parafusos
fornecidos (ref.A).
Para instalar a caixa das ligações:
abra a caixa (ref.B);
insira o dente inferior na respetiva ranhura (ref.C), na parte
lateral do aparelho;
encaixe a parte superior da caixa na parte lateral (D);
fixe-a com os dois parafusos fornecidos (ref.E);
fixe o cabo de terra (ref.M) à estrutura do ventiloconvector/
ventiloradiador, utilizando o parafuso fornecido (deve ser
aplicada uma força mínima de aberto de cerca de 2N);
ligue o engate rápido do Motor (MOTOR) ao presente na
placa (ref.I) *;
no par de terminais GRID (ref.L) está presente uma ponte
que assegura o funcionamento das versões Design Inverter
PT
ações
que
não
devem
CBD 35 - CONTROL PANEL BOARD (TOP)
Preliminary instructions
This instruction booklet is an integral part of the manual
of the device on which you install the kit. In that manual,
please refer to the WARNINGS and the BASIC SAFETY RULES.
The following symbols are used in this publication:
WARNING = actions requiring special care and
appropriate training.
DO NOT = actions that MUST ON NO ACCOUNT be
carried out.
Versions
Codes
20116408
CBD 35 - Control panel board (TOP)
Mounting, setting and connection of on-
board machine control panels
The
control
panel
performs
temperature (30 ° C) and maximum summer temperature
(20 ° C) functions, has independent free contacts to control
a chiller instead a boiler and a presence input.
It has an 230V output for driving the summer and winter
solenoid valves.
Mounting
Place the control panel into its housing in the upper part
of the cooler-convector/cooler-radiator and fix it with the
two supplied screws (ref. A).
To install the connection box:
open the box (ref. B);
insert the lower lug into the special slot (ref. C) on the
side of the appliance;
hook the upper part of the box to the side (ref. D);
fix it with the two supplied screws (ref. E);
fix the earth wire (rif. M) to the cooler-convector/
cooler-radiator structure using the supplied screws
(the minimum force of about 2N must be used when
screwing-up);
connect the rapid connector on the motor (MOTOR) to
that on the board (ref. I) *;
the 2 terminals of the GRID clamp (ref. L) feature a
1
EN
the
minimum
winter
Doc-0091331 Rev. 0