Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BDS MABasic 200
Summary of Contents for BDS MABasic 200
- Page 1 Translation of the Original Operating Instructions MABasic 200, 400, 450, 850...
-
Page 3: Table Of Contents
This product may not be disposed of use and pass them onto the next owner of in the European Union via the normal the machine. household refuse. Dispose of the device via communal collection points. MABasic 200, 400, 450, 850... - Page 4 If the situation is not avoided, it may lead to material damage. ► Follow the instructions in this warning to avoid material damage. NOTE ► A note indicates additional information that simplifies the use of the machine. MABasic 200, 400, 450, 850,...
-
Page 5: Safety
■ Pay attention to cleanliness at the workplace. ■ Keep the machine clean, dry and free of oil and grease. ■ Follow the instructions on lubricating and cooling the tool. MABasic 200, 400, 450, 850... - Page 6 Wear protective gloves when removing swarf. ► When working on scaffolding, the op- erator must be secured with a safety belt as the machine can oscillate dan- gerously in the event of interruption to the power supply. MABasic 200, 400, 450, 850,...
- Page 7 Electric shock hazard! cable. ► Do not pull the mains cable to remove Read the operating instructions the plug from the mains socket. before beginning work! Wear protective goggles and ear protection! MABasic 200, 400, 450, 850...
-
Page 8: Components / Delivery Contents
Core drilling machine Safety lashing strap ZAK075 ejector pin Transport case Hexagonal offset screwdriver: SW 4 for MABasic 200/400 SW5 for MABasic 450 SW5 + SW6 for MABasic 850 Industrial tool holder (ZIA 219 KN for MABasic 450 ZIA 319 KN and... -
Page 9: Before Using For The First Time
(21) supplied to prevent it from falling. ► Before using, check the safety lashing strap for proper function. A damaged safety lashing strap may not be used. Replace a damaged safety lashing strap immediately. MABasic 200, 400, 450, 850... - Page 10 NOTE paint, zinc and scale coatings and rust. The substrate must satisfy the following ► BDS offers a range of accessories conditions in order to achieve sufficient with special clamping devices for magnetic holding force: tubes and non-magnetic materials.
- Page 11 (2) the hexagonal offset screwdriver (24) using the hexagonal offset screwdriv- supplied and remove the core drill er (24) supplied and remove the core from below. drill from below. MABasic 200, 400, 450, 850...
-
Page 12: Use
▲ ► The machine switches off automati- Level 2 ▼ ▼ cally in the event of a power failure or Level 3 ▲ ▲ if the magnetic clamp is switched off. Level 4 ▲ ▼ MABasic 200, 400, 450, 850,... -
Page 13: Eliminating Blockages
ZHS 400 grease spray. Spray the drill on the inside and outside before drill- ing. In the case of larger drill depths, repeat this procedure. ► Make sure that swarf is removed regularly. With larger drilling depths, break up the swarf. MABasic 200, 400, 450, 850... -
Page 14: Cleaning
Replacing the carbon brushes ATTENTION Replacement of the carbon brushes may only be carried out by BDS or by an au- ► Never immerse the machine in water thorised specialist workshop. Unauthorised or other liquids. -
Page 15: Troubleshooting
The lubrication system does Lubricant tap closed. Open the lubricant tap. not function. Connecting nipple clogged. Clean the tank and nipple. NOTE ► If you cannot resolve the problem with the steps described above, please contact customer service. MABasic 200, 400, 450, 850... -
Page 16: Technical Data
Core drill assembly dustrial tool holder 19 mm (3/4“) 19 mm (3/4“) (3/4“) (3/4“) MK3/32 mm ( 1 1 /4“) Connecting cable length: Protection class Protection type IP20 IP20 IP20 IP20 IP20 MABasic 200, 400, 450, 850,... -
Page 17: Ec Declaration Of Conformity
We hereby declare that the product: Magnetic core drilling machine Model: Model MABasic 200, 400, 450, 850 conforms to the following relevant regulations: EC Directive 2006/42/EC on machinery ■ The following harmonised standards were applied in whole or in part: ●... - Page 18 MABasic 200, 400, 450, 850,...
- Page 20 BDS Maschinen GmbH Martinstraße 108 D-41063 Mönchengladbach Fon: +49 (0) 2161 / 3546-0 Fax: +49 (0) 2161 / 3546-90 Internet: www.bds-maschinen.de E-mail: info@bds-maschinen.de...