Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for BDS MABasic 200
Summary of Contents for BDS MABasic 200
-
Page 1: Operating Instructions
Translation of the Original Operating Instructions MABasic 200, 400, 450, 850... -
Page 3: Table Of Contents
Keep these operating instructions for later This product may not be disposed of in use and pass them onto the next owner of the domestic refuse within the the machine. European Union. Dispose of the device via communal collection points. MABasic 200, 400, 450, 850... -
Page 4: Intended Use
If the situation is not avoided, it may lead tions. to material damage. ► Follow the instructions in this warning to avoid material damage. NOTE ► A note indicates additional information that simplifies the use of the machine. MABasic 200, 400, 450, 850... -
Page 5: Safety
Make sure that your workplace is clean. function of the switches on the machine. ■ Keep the machine clean, dry and free of oil and grease. ■ Follow the instructions on lubricating and cooling the tool. MABasic 200, 400, 450, 850... - Page 6 Wear protective gloves when removing swarf. ► When working on scaffolding, the operator must be secured with a safety belt as the machine can oscillate dan- gerously in the event of interruption to the power supply. MABasic 200, 400, 450, 850...
- Page 7 Electric shock hazard! machine and not the connecting cable. ► Do not pull the mains cable to remove Read the operating instructions the plug from the mains socket. before beginning work! Wear protective goggles and ear protection! MABasic 200, 400, 450, 850...
-
Page 8: Components / Delivery Contents
Delivery contents Core drilling machine Safety lashing strap ZAK075 ejector pin Transport case Hexagonal offset screwdriver SW 4 for MABasic 200/400 SW5 for MABasic 450 SW5 + SW6 for MABasic 850 Industrial holder (ZIA219KN for MABasic 450 ZIA319KN and ZIA32KN for MABasic 850) -
Page 9: Before Using For The First Time
(21) supplied to prevent it from falling. ► Before using, check the safety lashing strap for proper function. A damaged safety lashing strap may not be used. Replace a damaged safety lashing strap immediately. MABasic 200, 400, 450, 850... -
Page 10: Inserting The Tool
NOTE zinc and scale coatings and rust. The substrate must satisfy the following con- ► BDS offers a range of accessories with ditions in order to achieve sufficient magnetic special clamping devices for tubes and clamping force: non-magnetic materials. - Page 11 ‹ tool mount (2) using the hexagonal tool mount (2) using the hexagonal offset screwdriver (24) supplied and offset screwdriver (24) supplied and remove the core drill from below. remove the core drill from below. MABasic 200, 400, 450, 850...
-
Page 12: Use
▼ ▼ ► The machine switches off automatically Stage 2 in the event of a power failure or if the ▲ ▲ Stage 3 magnetic clamp is switched off. ▲ ▼ Stage 4 MABasic 200, 400, 450, 850... -
Page 13: Eliminating Blockages
400 grease spray.Spray the drill on the inside and outside before drilling. Repeat this procedure when drilling deeper holes. ► Make sure that swarf is removed regu- larly. With larger drilling depths, break the chip. MABasic 200, 400, 450, 850... -
Page 14: Cleaning
Replacing the carbon brushes ATTENTION Replacement of the carbon brushes may only be carried out by BDS or by an au- ► Never immerse the machine in water thorised specialist workshop. Unauthorised or other liquids. -
Page 15: Troubleshooting
Lubricant tap closed. Open the lubricant tap. not function. Connecting nipple clogged. Clean the tank and nipple. NOTE ► If you cannot resolve the problem with the steps described above, please contact cus- tomer service. MABasic 200, 400, 450, 850... -
Page 16: Technical Data
MK3/19 mm (3/4“) Weldon Weldon MK2/19 mm (3/4“) Core drill assembly MK3/32 mm ( 1 1 /4“) 19 mm (3/4“) 19 mm (3/4“) industrial industrial Connecting cable length Protection class Protection type IP20 IP20 IP20 IP20 MABasic 200, 400, 450, 850... -
Page 17: Ec Declaration Of Conformity
We hereby declare that the product: Model: Magnetic core drilling machine Model MABasic 200, 400, 450, 850 conforms to the following relevant regulations: ■ EC Directive 2006/42/EC on machinery The following harmonised standards were applied in whole or in part: ●... - Page 18 MABasic 200, 400, 450, 850...
- Page 20 BDS Maschinen GmbH Martinstraße 108 D-41063 Mönchengladbach Fon: +49 (0) 2161 / 3546-0 Fax: +49 (0) 2161 / 3546-90 Internet: www.bds-maschinen.de E-Mail: info@bds-maschinen.de...