Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BDS MAB 100 K
Summary of Contents for BDS MAB 100 K
- Page 1 Translation of the Original Operating Instructions MAB 100 K...
- Page 3 Dispose of the device via communal collection points. The lubricant used can contain substances dangerous to the environment. Dispose of the lubricant according to local regulations. Observe the disposal instructions from the lubricant manufacturer. MAB 100 K...
- Page 4 If the situation is not avoided, it may lead tions. to material damage. ► Follow the instructions in this warning to avoid material damage. NOTE A note indicates additional information that simplifies the use of the machine. MAB 100 K...
-
Page 5: Safety
■ Before beginning work, check the condi- ■ Keep the machine clean, dry and free of tion of the machine accessories. oil and grease. ■ Follow the instructions on lubricating and cooling the tool. MAB 100 K... - Page 6 A glove can be caught by the drilling machine and torn off the hand. Risk of losing one or more fingers. ► Remove loose jewellery before begin- ning work. ► Wear a hair net if you have long hair. MAB 100 K...
- Page 7 ► Check that the tool is tightened securely before using (see section „Inserting the tool“). ► Do not allow the connecting cable to hang over edges (trip effect). MAB 100 K...
-
Page 8: Personal Protective Equipment
Helmet for protecting your head against falling objects Electric shock hazard! Wear a harness where there is a danger of falling. Read the operating instructions before beginning work! Gloves for protection against injuries Wear protective goggles and ear protection! MAB 100 K... -
Page 9: Components / Delivery Contents
Machine slide with guide Operating panel (see Fig.1) Motor ON/OFF switch Magnet ON/OFF switch (Main switch) Scope of supply MAB 100 K core drilling machine ZAK075 ejector pin Safety chain Transport case (not illustrated) Operating instructions/guarantee card (not illustrated) MAB 100 K... -
Page 10: Preparation
(10) of the machine before use. ed in the section „Personal protec- ► Eliminate unevenness, rust as well tive equipment“. as dirt and grease residue from the substrate. ► The BDS range of accessories in- cludes special holding devices. MAB 100 K... -
Page 11: Inserting The Tool
(clamping pieces with an uneven surface. sleeve). The sleeve snaps in automat- NOTE ically. ► BDS offers a range of accessories WARNING with special clamping devices for tubes and non-magnetic materials. Risk of injury from incorrectly inserted tool! Inserting the tool ►... -
Page 12: Using
Switch of the motor of the machine (see section „Switching off the machine“). ► Switch off the machine with the main switch (22) (see section „Deactivat- ing the magnetic clamp“). ► Disconnect the voltage supply (pull out the mains plug). MAB 100 K... - Page 13 The drilling process is not accelerated by higher pressure. The drill wears faster and the ma- chine can be overloaded. ► Use the high-performance BDS 5000 cutting oil in the cooling lubricant system of the machine. MAB 100 K...
-
Page 14: Eliminating Blockages
Clean the guide of the machine slide ‹ Replace defective tool if necessary. ‹ (11). Put the machine and accessories into ‹ NOTE the transport case. ► The BDS range of accessories in- cludes special devices (e.g., POW 200) for removing swarf. MAB 100 K... -
Page 15: Customer Service/Service
Tighten the adjusting screws evenly. ‹ Tighten the clamping bolts again. ‹ Replacing the carbon brushes Replacement of the carbon brushes may only be carried out by BDS or by an au- thorised specialist workshop. Unauthorised repairs will invalidate the guarantee. MAB 100 K... -
Page 16: Troubleshooting
The lubrication system does Lubricant tap closed. Open the lubricant tap. not function. Clean container and connect- Connecting nipple clogged. ing nipple. NOTE ► If you cannot resolve the problem with the steps described above, please contact customer service. MAB 100 K... -
Page 17: Technical Data
Technical data Technical data Model MAB 100 K Unit Dimensions 230 x 157 x 370 (L x W x H) Magnetic foot (L x W) 160 x 80 Approx. net weight. 230 V / 50-60 Hz Operating voltage (see type plate) -
Page 18: Ec Declaration Of Conformity
D-41063 Mönchengladbach We hereby declare that the product: Model: Magnetic core drilling machine Model MAB 100 K conforms to the following relevant regulations: ■ EC Directive 2006/42/EC on machinery The following harmonised standards were applied in whole or in part: ●... - Page 19 Fig. 1...
- Page 20 BDS Maschinen GmbH Martinstraße 108 D-41063 Mönchengladbach Fon: +49 (0) 2161 / 3546-0 Fax: +49 (0) 2161 / 3546-90 Internet: www.bds-maschinen.de E-Mail: info@bds-maschinen.de...
Need help?
Do you have a question about the MAB 100 K and is the answer not in the manual?
Questions and answers