Table of Contents
Advertisement
Quick Links
This user's guide gives a general overview of the AFE5832 evaluation module (EVM) and provides a
general description of the features and functions to be considered while using this module. This manual is
applicable to the AFE5832 analog front-end, and to the Rev. A version of the EVM hardware. The
AFE5832 EVM provides a platform for evaluating the AFE under various signal, clock, reference, and ADC
output formats. In addition, the EVM supports the testing of the low-voltage differential signaling (LVDS)
interface using the TSW1400EVM capture card.
This user's guide refers to software AFE5832 GUI v.1.0.0 or higher, and High-Speed Data Converter Pro
(HSDC Pro) Software v.4.7 and requires Microsoft Windows 7
For any further questions regarding the EVM, GUI or device, contact TI support.
1
2
3
3.1
4
4.1
4.2
5
6
Appendix B
Overview of the AFE5832 EVM GUI Features
Appendix C
Hardware Configuration
Appendix D
Triggering Options
Appendix E
Common Hardware Modifications
Appendix F
Hardware Reference
Appendix G
FAQ and Troubleshooting
1
AFE5832 EVM Hardware Overview
2
Provided Power Cable for J1 Connector
3
Evaluation Setup Overview
4
TSW1400EVM and AFE5832 EVM Hardware Setup for LVDS Capture
5
Connect to TSW EVM (TSW1400 Shown)
6
Choose Firmware
7
TSW1400 EVM LEDs Turn On After Firmware Download
8
AFE5832 GUI Launches
9
Clock Configuration on AFE EVM for LVDS Capture
10
Software Reset and Initialize Buttons on AFE5832 EVM GUI
11
AFE_RST Hardware Reset Button
12
AFE5832 EVM GUI Data Format and Analog Configuration (LVDS)
13
LED D5 on the TSW1400 EVM Turns On When ADC is Ready
SLOU489 - August 2017
Submit Documentation Feedback
AFE5832 32-Channel Analog Front-End
Evaluation Module (EVM Rev. A)
...................................................................................................
...................................................................................................
.......................................................................................
..............................................................................................
..............................................................................................
..............................................................................................
..........................................................................................
.................................................................................................
...............................................................................
..............................................................................................
........................................................................................
List of Figures
.......................................................................................
.................................................................................
.................................................................................................
.............................................................................
..........................................................................................................
..................................................................................................
.......................................................................................
AFE5832 32-Channel Analog Front-End Evaluation Module (EVM Rev. A)
Copyright © 2017, Texas Instruments Incorporated
or Windows 10
®
Contents
..................................................................
...................................................................
.................................................
...............................................
................................................................
............................................
...........................................................
.................................................................
.......................................................
...............................................
.....................................................
User's Guide
SLOU489 - August 2017
to function.
®
4
5
6
6
8
8
10
15
17
19
34
49
54
57
58
82
4
5
6
8
10
10
11
11
12
12
12
13
14
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Texas Instruments AFE5832
Summary of Contents for Texas Instruments AFE5832
-
Page 1: Table Of Contents
This manual is applicable to the AFE5832 analog front-end, and to the Rev. A version of the EVM hardware. The AFE5832 EVM provides a platform for evaluating the AFE under various signal, clock, reference, and ADC output formats. - Page 2 ....................Default Jumper Positions .................. EVM ADC Clock Source Configuration .............. AFE EVM ADC Clock Source Configuration Schematic AFE5832 32-Channel Analog Front-End Evaluation Module (EVM Rev. A) SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 3 Python is a registered trademark of Python Software Foundation. Xilinx is a trademark of Xilinx Incorporated. All other trademarks are the property of their respective owners. SLOU489 – August 2017 AFE5832 32-Channel Analog Front-End Evaluation Module (EVM Rev. A) Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
-
Page 4: Evm Hardware Overview
The EVM received should resemble Figure 1. For more hardware details and the default jumper map, see Appendix AFE5832 32-Channel Analog Front-End Evaluation Module (EVM Rev. A) SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated... -
Page 5: Gui Software Installation
Figure 2. Provided Power Cable for J1 Connector GUI Software Installation The AFE5832 EVM and the TSW capture card EVM have individual software and both require software installations. Ensure that no USB connections are made to the EVMs until after the installations are complete. -
Page 6: Quick Views Of Evaluation Setups For Lvds Interface
EVM kit. USB Interface to PC: The USB connections from the AFE5832 EVM and TSW EVM to the PC are used for communication from the GUIs to the boards. USB 2.0 or 3.0 ports are both acceptable. - Page 7 J39 or J56 (GUI configuration is required for the external clock configuration). For more information on clock configuration, see Section C.1.3. SLOU489 – August 2017 AFE5832 32-Channel Analog Front-End Evaluation Module (EVM Rev. A) Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
-
Page 8: Testing The Evm Data Capture With Lvds Interface
Appendix A, connect the USB cable from the PC to J65 (USB) located on the top side of the AFE5832 EVM. Connect the USB cable from PC to J5 (USB_IF) of the TSW1400 EVM. NOTE: TI recommends that the PC USB port be able to support USB2.0. If unsure, always choose the USB ports at the back of the PC chassis over ones located on the front or sides. - Page 9 S4 should be 'off' immediately after powering up the board for LVDS capture, but can be manipulated for other modes. For more information on the Complex Programmable Logic Device (CPLD), refer to Section C.1.4. SLOU489 – August 2017 AFE5832 32-Channel Analog Front-End Evaluation Module (EVM Rev. A) Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
-
Page 10: Capturing An Analog Input Signal With The Lvds Interface
Capturing an Analog Input Signal With the LVDS Interface This section describes the software setup for capturing an analog input using the AFE5832 EVM. If there is any issue with a data capture, refer to the troubleshooting section. Data capture is confirmed by using only the Quick Setup page of the AFE5832 GUI. Assuming the... - Page 11 Figure 7. TSW1400 EVM LEDs Turn On After Firmware Download 9. The AFE5832 EVM GUI opens automatically. Wait until this is finished before continuing. If any errors arise at this time, contact TI support. Figure 8. AFE5832 GUI Launches SLOU489 –...
- Page 12 J56. Figure 9. Clock Configuration on AFE EVM for LVDS Capture 2. Press the DUT RESET button on the AFE5832 GUI. 3. Press the Initialize Device button on the AFE5832 EVM GUI (Figure 10). These buttons are located close to the upper left-hand corner of the GUI window.
- Page 13 DTGC Modes: Select ‘Programmable Fixed-Gain Mode’ NOTE: Ensure the right CPLD switches are configured on S5 as detailed for each capture mode. Figure 12. AFE5832 EVM GUI Data Format and Analog Configuration (LVDS) SLOU489 – August 2017 AFE5832 32-Channel Analog Front-End Evaluation Module (EVM Rev. A) Submit Documentation Feedback Copyright ©...
- Page 14 Figure 14. Analog Input Capture for LVDS AFE5832 32-Channel Analog Front-End Evaluation Module (EVM Rev. A) SLOU489 – August 2017 Submit Documentation Feedback...
-
Page 15: Testing The Evm In Digital Time Gain Compensation (Dtgc) Mode
Figure 15. DTGC Mode Test: AFE5832 EVM Switches (S5) d. Choose AFE5832.ini as firmware on HSDC Pro. e. Change the DTGC Mode on the AFE5832 EVM GUI to ‘Up-Down Ramp Mode’ and configure the other formats as shown in Figure Figure 16. - Page 16 Press the Capture button on HSDC Pro. i. The Up-Down Ramp DTGC waveform should appear similar to Figure Figure 19. DTGC Mode Test: Waveform AFE5832 32-Channel Analog Front-End Evaluation Module (EVM Rev. A) SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
-
Page 17: Using The Evm In Cw Mode
Using the EVM in CW Mode www.ti.com Using the EVM in CW Mode Demonstrating the CW mixer in the AFE is done by following these steps: 1. In the AFE5832 GUI, reset and initialize the device by referring to Figure 10 Figure 11. Remember to connect a –5-V and a 5-V source to the device. - Page 18 Using the EVM in CW Mode www.ti.com Figure 21. CW Output AFE5832 32-Channel Analog Front-End Evaluation Module (EVM Rev. A) SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
-
Page 19: Appendix A Software Installation
GUI used to control a suite of FPGA capture solutions including the TSW1400. Section A.2 provides details for installing the AFE5832 EVM GUI. High Speed Data Converter Pro (HSDC Pro) GUI Installation Download HSDC Pro v.4.7 from the mySecureSoftware folder at https://www.ti.com/securesoftware/docs/securesoftwarehome.tsp. -
Page 20: Hsdc Pro Install (Ti License Agreement)
High Speed Data Converter Pro (HSDC Pro) GUI Installation www.ti.com 3. Read the License Agreement from Texas Instruments and select I accept the License Agreement, then press the Next button as shown in Figure Figure 23. HSDC Pro Install (TI License Agreement) 4. -
Page 21: Hsdc Pro Install (Install Directory)
Figure Figure 25. HSDC Pro Install (Install Directory) 6. Click Next to begin the installation, as in Figure Figure 26. HSDC Pro Install (Installation Ready) SLOU489 – August 2017 Software Installation Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated... -
Page 22: Hsdc Pro Install (Cypress Driver Install)
Figure 27. HSDC Pro Install (Cypress Driver Install) 8. Click Finish to continue installation, as shown in Figure Figure 28. HSDC Pro Install (Continue Installation) Software Installation SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated... -
Page 23: Hsdc Pro Install (Continue Driver Installation)
Figure 29. HSDC Pro Install (Continue Driver Installation) 10. Finish HSDC Pro installation by choosing the appropriate installation options and pressing Finish, as Figure Figure 30. HSDC Pro Install (Finish Installation) SLOU489 – August 2017 Software Installation Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated... - Page 24 Run as Administrator. Press the Next button once the graphic in Figure 31 appears. Figure 31. AFE5832 GUI Install (Begin Installation) 2. Read the Texas Instruments License Agreement and select I accept the agreement followed by the Next button, as in Figure Software Installation SLOU489 –...
- Page 25 AFE5832 GUI Installation www.ti.com Figure 32. AFE5832 GUI Install (TI License Agreement) SLOU489 – August 2017 Software Installation Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
-
Page 26: Afe5832 Gui Install (Begin Installation)
License Agreement and select I accept the agreement followed by the ® Next button, as in Figure Figure 33. AFE5832 GUI Install (National Instruments License Agreement) ® 4. Read the PSF License Agreement for Python 2.7 and select I accept the agreement followed by the ®... - Page 27 AFE5832 GUI Installation www.ti.com Figure 34. AFE5832 GUI Install (PSF License Agreement) SLOU489 – August 2017 Software Installation Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 28 5. Allow the software to be installed in the default location by pressing the Next button, as in Figure Figure 35. AFE5832 GUI Install (Install Directory) 6. Select the components to install and press Next. Figure 36. AFE5832 GUI Install (Select Components) Software Installation SLOU489 –...
- Page 29 AFE5832 GUI Installation www.ti.com 7. Pressing the Next button begins installation, as shown in Figure Figure 37. AFE5832 GUI Install (Installation Ready) 8. The window shown in Figure 38 appears showing that the installation is in progress. Figure 38. AFE5832 GUI Install (Installation Progress) SLOU489 –...
-
Page 30: Afe5832 Gui Install (Psf License Agreement)
9. A window for the Python 2.7 Setup comes up. Select Install for all users as in Figure Figure 39. AFE5832 GUI Install (Installation for Users) If Python is already installed, select the option for Repair Python 2.7. Proceed to step 13 and click the Finish button. -
Page 31: Afe5832 Gui Install (Install Directory)
AFE5832 GUI Installation www.ti.com 10. Allow the software to be installed in the default destination directory as in Figure Figure 41. AFE5832 GUI Install (Destination Directory) 11. Click Next on the screen displayed in Figure Figure 42. AFE5832 GUI Install (Customize Python ®... -
Page 32: Afe5832 Gui Install (Select Components)
AFE5832 GUI Installation www.ti.com 12. The window shown in Figure 43 appears showing that the installation is in progress. Figure 43. AFE5832 GUI Install (Python Installation Progress) ® 13. Press the Finish button, as in Figure Figure 44. AFE5832 GUI Install: (Python Finished) ®... -
Page 33: Afe5832 Gui Install (Finished)
Figure 45. AFE5832 GUI Install (Finished) The AFE5832 GUI is launched automatically from HSDC Pro, once a device has been selected. Therefore, there is no need to launch AFE5832 GUI manually and there is no need for a desktop shortcut. SLOU489 – August 2017... -
Page 34: Afe5832: Hovering Over Controls
Overview of the AFE5832 EVM GUI Features This section provides a quick overview of the features and functions of the AFE5832 EVM GUI. The GUI allows the user to easily configure the various functions of the AFE such as receiver gain, bandwidth settings, and timing or clocking control settings. - Page 35 – Digital Signal Processing • Digital_Offset • Digital_Gain • Invert_LVDS • Misc DSP Setup • DIG_HPF • Register Map Configuration SLOU489 – August 2017 Overview of the AFE5832 EVM GUI Features Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
-
Page 36: Afe5832: Quick Setup Tab
4. Information boxes on the right-hand side that display the HSDC Pro related Parameters and Device Status Figure 47 illustrates the AFE5832 Quick Setup tab. Figure 47. AFE5832: Quick Setup Tab Overview of the AFE5832 EVM GUI Features SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated... -
Page 37: Afe5832: Quick Setup: Hsdc Pro Related Parameters
• ADC Input Target Frequency: This frequency should closely match the input signal that is being supplied Figure 48. AFE5832: Quick Setup: HSDC Pro Related Parameters SLOU489 – August 2017 Overview of the AFE5832 EVM GUI Features Submit Documentation Feedback... -
Page 38: Afe5832: Vca: Vca And Cw Mixer
B.2.1 VCA and CW Mixer Subtab The VCA and CW Mixer subtab for the AFE5832 has the following features: 1. Settings for configuring LNA high-pass filter and setting corner and cut-off frequencies 2. Enable or disable LNA HPF at certain channel inputs 3. -
Page 39: Afe5832: Vca: Dtgc
B.2.2 DTGC Subtab The DTGC subtab for the AFE5832 has the following features: 1. Options for selecting different DTGC modes and setting parameters within these modes 2. Enable interrupts and provide pulses on the TGC pin 3. Configure specific parameters for different profiles by setting gains, start and stop indices, and attenuation factors 4. -
Page 40: Afe5832: Adc: Top Level
Processing. B.3.1 Top Level Subtab The Top Level subtab for the AFE5832 has the following features: 1. Enabling and disabling the LVDS interface and selecting data rates, delays, and resolutions 2. Powering down individual LVDS output lines 3. Software and PLL resets Figure 51. -
Page 41: Afe5832: Adc: Test Pattern
B.3.2 Test Pattern Subtab The Test Pattern subtab for the AFE5832 has the following feature: • Selecting preset or custom test patterns to be generated by ADC for LVDS or on certain clock lines Figure 52. AFE5832: ADC: Test Pattern SLOU489 –... -
Page 42: Afe5832: Adc: Digital Signal Processing
B.3.3 Digital Signal Processing Subtab The Digital Signal Processing subtab for the AFE5832 has the following features: 1. Setting the digital gain and digital offset or automatically calculating a channel offset for each of the 16 ADC channels, individually 2. -
Page 43: Clicking On Register And Field Names
Register Map. Figure 54. Clicking on Register and Field Names SLOU489 – August 2017 Overview of the AFE5832 EVM GUI Features Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated... -
Page 44: Afe5832: Register Map Configuration: Update Modes
There are two options to change the Update Mode on the GUI as shown in Figure 57: (a) Immediate and (b) Deferred. Figure 55. AFE5832: Register Map Configuration: Update Modes Overview of the AFE5832 EVM GUI Features SLOU489 – August 2017 Submit Documentation Feedback... -
Page 45: Afe5832: Register Map Configuration: Immediate Update Mode
3. Read All: This option reads data from all the registers in the device regardless of whether they are selected or not. Figure 56. AFE5832: Register Map Configuration: Immediate Update Mode SLOU489 – August 2017 Overview of the AFE5832 EVM GUI Features Submit Documentation Feedback Copyright ©... -
Page 46: Afe5832: Register Map Configuration: Deferred Update Mode
Read options can be used. The user is prompted to either write the modified fields to the device or discard the changes. Figure 57. AFE5832: Register Map Configuration: Deferred Update Mode Overview of the AFE5832 EVM GUI Features SLOU489 – August 2017 Submit Documentation Feedback Copyright ©... -
Page 47: Afe5832: Register Map Configuration: Changing Register Value
The value for a specific bit can also be changed by clicking on the bit in the register map. Figure 58. AFE5832: Register Map Configuration: Changing Register Value SLOU489 – August 2017 Overview of the AFE5832 EVM GUI Features Submit Documentation Feedback Copyright ©... -
Page 48: Afe5832: Register Map Configuration: Manual Data Entry
Clicking Read Generic will read the data from that register and the hexadecimal value will show up in the Read Data field. Figure 59. AFE5832: Register Map Configuration: Manual Data Entry Overview of the AFE5832 EVM GUI Features SLOU489 – August 2017 Submit Documentation Feedback Copyright ©... -
Page 49: Default Jumper Positions
EVM that are useful for debug and general-use purposes. C.1.1 EVM Header Configuration The AFE5832 EVM is flexible in its configurability through the use of 2- and 3-pin headers. The default configuration of the EVM is set to facilitate initial testing, requiring minimal bench equipment. Figure 60 shows the default positions of all headers. - Page 50 LNA TR Enable TR_EN 1-4 – – C.1.2 EVM Testpoints Table 2 lists all test points on the AFE5832 EVM and their purposes. Table 2. EVM Rev. A Testpoints Testpoint Circuit Label Testpoint Description TP62-65, 69 Digital Ground Reference for EVM...
- Page 51 (auto-detect feature). Therefore, the EVM allows for multiple clocking options. Figure 61. EVM ADC Clock Source Configuration SLOU489 – August 2017 Hardware Configuration Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 52 63). Connect a single-ended external clock generator to SMA J39. Set the clock source to an appropriate frequency, such as 10 MHz to 100 MHz, and +13-dBm amplitude. Hardware Configuration SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 53 Complex Programmable Logic Device (CPLD) The AFE5832 board has a Xilinx™ CPLD, designated by U21 on the schematic. This CPLD is controlled by four switches contained in S5 on the board. When all of these switches are in the ‘off’ position, LEDs D5 –...
- Page 54 Refer to the ADC Synchronization Using TX_TRIG and Input Multiplexer and Sampler sections in the AFE5832 data sheet (SBAS823) for more information. Software Trigger One method of triggering the TSW EVM, AFE EVM as well as other bench equipment such as function generators is to generate the trigger from the TSW EVM itself.
- Page 55 PRF Trigger Signal Generator 3.3V pulse @ PRF TX_TRIG Trigger Input(J11) Signal Analog Input ADC Data AFE58xxxx TSW1400 Generator Figure 67. HSDC Pro Trigger Configuration for HW SLOU489 – August 2017 Triggering Options Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 56 External Trigger www.ti.com Figure 68. HSDC Pro Trigger Configuration for HW External Trigger Triggering Options SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 57 The AFE EVM allows for external access to the SPI bus for the AFE only, not the LMK device. This is done by connecting SPI signals at J64 and removing R140 near U14 on the bottom side of the board. SLOU489 – August 2017 Common Hardware Modifications Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 58 LVDS Output (J48) to TSW1400 EVM TGC Source CW Clock Decoupling/ LMK0482x CPLD ADC Clock Hardware Clock Device (U4) XTAL/SMA Figure 69. AFE5832 EVM Block Diagram Hardware Reference SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 59 DGND SDOUT_POST SDOUT_3.3 OUTD R140 USB_SPI_EN TXB0106PWR GND1 GND2 GND1 GND2 DGND ISO7141CCDBQR TP66 DGND Figure 70. AFE5832 Rev. A EVM Schematic 1 of 12 SLOU489 – August 2017 Hardware Reference Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 60 CPLD_IO_7 CPLD_SW2 CPLD_SW3 CPLD_SW4 I/O, GTS1 I/O, GTS0 I/O, GTS3 I/O, GTS2 I/O, GSR XC2C64A-5QFG48C Figure 71. AFE5832 Rev. A EVM Schematic 2 of 12 Hardware Reference SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 61 DOUTM15 TSW_GPIO_1 DOUTP15 DOUTM7 TSW_GPIO_2 DOUTP7 TSW_GPIO_3 DOUTM16 TSW_GPIO_4 DOUTP16 DCLKM TSW_GPIO_5 DCLKP TSW_GPIO_6 TSW_GPIO_7 Figure 72. AFE5832 Rev. A EVM Schematic 3 of 12 SLOU489 – August 2017 Hardware Reference Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 62 TP30 R188 AGND R189 SMA_INP16 SMA_INP32 TP31 TP32 TP33 TP34 AGND AGND AGND AGND AGND Figure 73. AFE5832 Rev. A EVM Schematic 4 of 12 Hardware Reference SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 63 0.1uF 140k 0.1uF 0.1uF OPAMP- OPAMP- OPAMP- OPAMP+ U19B OPA2614ID R177 R178 C261 0.1uF OPAMP- Figure 74. AFE5832 Rev. A EVM Schematic 5 of 12 SLOU489 – August 2017 Hardware Reference Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 64 TSW_GPIO_5 TP35 CPLD_IO_6 TX_TRG TR ENABLE PINS TR_EN_OUT_3 10pF 0.1uF 49.9 CPLD_IO_7 TR_EN_OUT_4 0.1uF 49.9 Figure 75. AFE5832 Rev. A EVM Schematic 6 of 12 Hardware Reference SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 65 CLKM _1XA_F CW1X_CLEAN_N 0.1uF C104 CW_CLKP1X_LMK CLK_CM_1X C105 0.1uF 0.1uF ADT4-1WT+ CW1X_CLEAN_P C106 CLKP_1XA_F CLKP_1X 0.1uF Figure 76. AFE5832 Rev. A EVM Schematic 7 of 12 SLOU489 – August 2017 Hardware Reference Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 66 0.1uF R127 R126 R128 R129 R130 +1.9V NR/FB TPS79601DCQR R131 1.65k C209 270pF R132 3.01k Figure 77. AFE5832 Rev. A EVM Schematic 8 of 12 Hardware Reference SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 67 TGC_PROF_1 TSW_GPIO_1 TGC_PROF_2 TGC_UP_DOWN _EXT TSW_GPIO_2 TGC_SLOPE_EXT TSW_GPIO_3 TGC_UP_DOWN _EXT CPLD_UD TGC_UP_DN TGC_SLOPE_EXT CPLD_SL TGC_SLOPE Figure 78. AFE5832 Rev. A EVM Schematic 9 of 12 SLOU489 – August 2017 Hardware Reference Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 68 TR_EN<2> TP52 C179 TR_EN_OUT_3 TR_EN<3> LNA_IN_ CME C180 TR_EN_OUT_4 TR_EN<4> LNA_IN_ CMO AFE5832ZBV AFE5832ZBV AGND Figure 79. AFE5832 Rev. A EVM Schematic 10 of 12 Hardware Reference SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 69 R100 OSCINn 120 ohm 0.01µF C159 C160 C161 C162 10pF 2200pF 100pF 0.1uF R101 40MHz Figure 80. AFE5832 Rev. A EVM Schematic 11 of 12 SLOU489 – August 2017 Hardware Reference Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 70 FCC disclaimer Label Tab le Variant Label Text AFE58JD32EVM AFE5832EVM FID1 FID2 FID3 FID4 FID5 FID6 Figure 81. AFE5832 Rev. A EVM Schematic 12 of 12 Hardware Reference SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 71 EVM Bill of Materials www.ti.com EVM Bill of Materials Table 3 lists the AFE5832 EVM bill of materials (BOM). Table 3. AFE5832 EVM Bill of Materials Package Alternate Alternate Designator Quantity Value Description PartNumber Manufacturer Reference Part Number Manufacturer C1, C2, C3, C4,...
- Page 72 EVM Bill of Materials www.ti.com Table 3. AFE5832 EVM Bill of Materials (continued) Package Alternate Alternate Designator Quantity Value Description PartNumber Manufacturer Reference Part Number Manufacturer C65, C66, C67, C68, C69, C70, C71, C72, C73, C74, C76, C77, C78, C79, C80,...
- Page 73 EVM Bill of Materials www.ti.com Table 3. AFE5832 EVM Bill of Materials (continued) Package Alternate Alternate Designator Quantity Value Description PartNumber Manufacturer Reference Part Number Manufacturer CAP, CERM, 10 GRM1555C1H100J C127, C129, C159 10pF pF, 50 V, +/- 5%, 0402...
- Page 74 EVM Bill of Materials www.ti.com Table 3. AFE5832 EVM Bill of Materials (continued) Package Alternate Alternate Designator Quantity Value Description PartNumber Manufacturer Reference Part Number Manufacturer CAP, CERM, C193 470pF 470pF, 50V, +/-5%, 0603 06035A471JAT2A C0G/NP0, 0603 CAP, CERM, 15...
- Page 75 EVM Bill of Materials www.ti.com Table 3. AFE5832 EVM Bill of Materials (continued) Package Alternate Alternate Designator Quantity Value Description PartNumber Manufacturer Reference Part Number Manufacturer HEX STANDOFF HEX STANDOFF H1, H5, H8, H13, 4-40 ALUMINUM 4-40 ALUMINUM 2203 Keystone 1/2"...
- Page 76 EVM Bill of Materials www.ti.com Table 3. AFE5832 EVM Bill of Materials (continued) Package Alternate Alternate Designator Quantity Value Description PartNumber Manufacturer Reference Part Number Manufacturer Power Jack, mini, Jack, 2.1mm OD, R/A, RAPC722X Switchcraft 14.5x11x9mm Terminal Block, On-Shore 3.5mm Pitch, 3x1, 10.5x8.2x6.5mm...
- Page 77 EVM Bill of Materials www.ti.com Table 3. AFE5832 EVM Bill of Materials (continued) Package Alternate Alternate Designator Quantity Value Description PartNumber Manufacturer Reference Part Number Manufacturer R44, R45, R56, R57, R58, R59, RES, 100, 1%, 0.1 R84, R105, R106, 0402...
- Page 78 EVM Bill of Materials www.ti.com Table 3. AFE5832 EVM Bill of Materials (continued) Package Alternate Alternate Designator Quantity Value Description PartNumber Manufacturer Reference Part Number Manufacturer RES, 3.30 k, 1%, R148, R171 3.30k 0.1 W, AEC-Q200 0402 ERJ-2RKF3301X Panasonic Grade 0, 0402 RES, 4.70 k, 1%,...
- Page 79 EVM Bill of Materials www.ti.com Table 3. AFE5832 EVM Bill of Materials (continued) Package Alternate Alternate Designator Quantity Value Description PartNumber Manufacturer Reference Part Number Manufacturer 32-Channel Ultrasound AFE with 41.5- mW/Channel Power, 1.5nV/vHz Noise, 12-Bit, 40- ZBV0289A AFE5832ZBV Texas Instruments...
- Page 80 EVM Bill of Materials www.ti.com Table 3. AFE5832 EVM Bill of Materials (continued) Package Alternate Alternate Designator Quantity Value Description PartNumber Manufacturer Reference Part Number Manufacturer Ultralow-Noise, High PSRR, Fast, RF, 1A, Low- U7, U8, U10 DCQ0006A TPS79601DCQR Texas Instruments...
- Page 81 EVM Bill of Materials www.ti.com Table 3. AFE5832 EVM Bill of Materials (continued) Package Alternate Alternate Designator Quantity Value Description PartNumber Manufacturer Reference Part Number Manufacturer Dual, High Gain Bandwidth, High Output Current, Operational U17, U18, U19, Amplifier with D0008A...
- Page 82 LED D8 on. Ensure that there is no SMA cable connected to J37 on the AFE5832EVM before retrying capture in HSDC Pro. Figure 82. Read DDR Error for No Capture FAQ and Troubleshooting SLOU489 – August 2017 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated...
- Page 83 IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are developing applications that incorporate TI products;...
Need help?
Do you have a question about the AFE5832 and is the answer not in the manual?
Questions and answers