Advertisement
Quick Links
2 Door Cupboard
Assembly Instructions
044 xx 9426
- Please keep for future reference
Dimensions
Width - 60.0cm
Depth - 34.8cm
Height - 104.6cm
Important -
Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Rev A - 19.06.19
Advertisement
Related Manuals for JD Williams 2 Door Cupboard 044 9426 Series
Summary of Contents for JD Williams 2 Door Cupboard 044 9426 Series
- Page 1 2 Door Cupboard Assembly Instructions 044 xx 9426 - Please keep for future reference Dimensions Width - 60.0cm Depth - 34.8cm Height - 104.6cm Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123 Please turn to back page for important information when contacting Customer Helpline.
- Page 2 Safety and Care Advice Important - Please read these instructions fully before starting assembly Do not stand or put weight on Check you have all the We do not the product, this could cause components and tools listed on recommend the damage.
- Page 3 Components - Panels Please check you have all the panels listed below Important - Thick lines indicate finished edges Left end Right end Door (96.8x34.6cm) Door (67.0x34.4cm) (96.8x34.6cm) (96.2x21.3cm) Code - 1482 Code - 1489 Code - 1483 Code - 1488 Bottom (60.0x34.8cm) (60.0x34.8cm)
-
Page 4: Components - Exploded View
Components - Exploded View 1480 1482 1490 1484 1487 1485 1487 1483 1488 1486 1489 1481... - Page 5 Components-Fittings Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly, In some case more fittings may be supplied than are required. Large cam x 10 Metal dowel x 10 45mm screw x 6 Code 760001103 Code 760003004...
- Page 6 Assembly Instructions Step 1 Fitting dowels to top panel Insert metal dowels into the divider panel 1480 1480 Note: Insert metal dowels as far as shown by arrows. Do not over tighten. Step 2 Fitting cams, dowels and hinge plates to the right hand end panel.
- Page 7 Assembly Instructions Step 3 Fitting cams,wooden dowels and hinge plates to left hand end panel. Insert hinge plates cams , wooden dowels into Use a hammer to knock in the lh end. wooden dowels 1482 into inner holes. Note: Ensure cam arrow points towards the edge with hole.
- Page 8 Assembly Instructions Step 5 Fitting cams to the shelf. Insert cams into the 1485 shelf 1485 Step 6 Correct Attach hinges to the doors. Insert hinges Incorrect into holes, ensure the hinge is straight (90 degree angle). 1489 Before securing the Bradawl hinges , we recommend...
- Page 9 Assembly Instructions Step 7 Connect the shelf to the rh end panel and divider. Connect the dowels in the rh end 1483 to the 1485 cams in shelf Connect the dowels in 1484 the divider to the 1485 cams in shelf 1484 1485 Turn the cam 180 degrees...
- Page 10 Assembly Instructions Step 9 Insert the back panel. Stand the unit upright Raw face to as shown. this side 1490 2 people required. Slide the back panel 1490 into the grooves in the end panels and the top panel. 1483 1482 1484 1480...
- Page 11 Assembly Instructions Step 11 Attach feet To locate feet to the bottom you will 1481 need to mark position with a bradawl 15mm and 38mm in as shown, Bradawl then screw the foot into place. Repeat in each corner. Lay unit on its front. 2 people required.
- Page 12 Assembly Instructions Step 12 Square up the unit. IMPORTANT Ensure a tape measure is used to square up unit! Before securing the back it is necessary to square up the unit. You can do this by measuring between XX - XX and YY - YY ensuring these are the same (DIAG 1).
- Page 13 Assembly Instructions Fittings you will need for this step: Step 14 Locate shelf studs Push shelf studs into panels 1482 1483 1484 1482 1483 1484 Step 15 Locate shelves onto shelf studs Locate shelves 1486 1487 onto shelf studs...
- Page 14 Assembly Instructions Step 16 Hanging doors With help, slot door hinges onto hinge plates. Ensure screw on hinge slides into the slot on hingeplate. See Diagrams 1, 2 and 3. Tighten screw shown to lock hinges in position. See ‘Hinge adjustment’ page if the doors need adjusting.
- Page 15 Assembly Instructions Step 17 Hinge adjustment To move doors up or down: loosen screws shown and move doors to suit. Re-tighten screws. To move doors in or out: loosen screw shown and move doors to suit. Re-tighten screws. To move doors left or right: loosen or tighten screw as shown.
- Page 16 Assembly Instructions Step 18 WARNING Fixing to wall We recommend that this IN ORDER TO PREVENT OVERTURNING THIS PRODUCT MUST BE USED WITH unit is fixed to a suitable THE WALL ATTACHMENT DEVICE wall to prevent possible PROVIDED overbalancing. We have Serious or fatal crushing injuries can occur from included a fixing bracket furniture tipping over.
- Page 17 Assembly Instructions Congratulations! Your unit is complete. Important Information If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123 8am - 4.30pm (Monday to Thursday) 8am - 2.30pm (Fridays) (by contacting the customer service line your statutory rights are not affected) Please have the following information to hand: >>...
- Page 18 Notes;...
- Page 19 Notes;...
- Page 20 Notes;...
Need help?
Do you have a question about the 2 Door Cupboard 044 9426 Series and is the answer not in the manual?
Questions and answers