Contents Contents ................ 2 Troubleshooting ............42 Safety Precautions ............3 Indicator and projector status ........42 No power ..............43 Safety ............... 3 No image ..............44 Specifications ..............4 No sound ..............45 Circuit Protections ............5 IC Block Diagrams ............46 How to check Lamp Used Time ........
Safety Precautions Safety Caution in moving or transporting the projector – Do not drop or bump the projector, otherwise damages Caution or malfunctions may result. ELECTRIC SHOCK – When carrying the projector, use a suitable carrying DO NOT OPEN case. CAUTION: –...
Circuit Protections This projector provides the following circuit protections to operate in safety. If the abnormality occurs inside the projector, it will automatically turn off by operating one of the following protection circuits. Thermal Switch Thermal Switch There is a thermal switch inside the projector to detect the lamp surrounding temperature rising abnormally.
Page 6
Circuit Protection POWER indicator The POWER indicator shows the state of the function which protects the projector. Check the state of the POWER indicator to take proper maintenance. The projector is shut down and the POWER indicator is POWER indicator flashing orange.
Page 7
Maintenance and cleaning Cleaning the filter The air filter prevents dust from accumulating on the surface of the optical elements inside the projector. Should the air filter become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in a buildup of internal heat and adversely affects the life of the projector.
Page 8
Maintenance and cleaning Clean the project lens Unplug the AC power cord before cleaning. Gently wipe the projection lens with a cleaning cloth that contains non-abrasive camera lens cleaner, or use a lens cleaning paper or commercially available air blower to clean the lens.
Page 9
Maintenance and cleaning Replace the lamp Lamp replacement icon When the projection lamp of the projector reaches its end of life,the Lamp replacement icon appears on the screen, Lamp replace please replace the lamp immediately. CAUTION FORBIDDEN As temperature inside the projector is high, you should For the sake of safety, only use the lamp of the same cool the projector for at least 45 minutes before you model.
Lamp Replacement Suggestion f the filter is blocked by dust, the effect of cooling fan will be reduced, and heat accumulate in the projector, service life will be shortened.shorten the service life of the lamp. Cleaning filter is suggested after lamp replacement.Replacement Refer to "Clean the filter".
Security Function Notice This projector provides security functions such as "Key lock", "PIN code lock" and "Logo PIN code lock". When the projector has set these security function on, you are required to enter correct PIN code to use the projector. If you do not know the correct PIN code to the projector, the projector can no longer be operated or started.
Mechanical Disassembly Mechanical disassembly should be made by following Screws Expression procedures chart. (Type Diameter x Length) mm Following steps show the basic procedures, therefore unnecessary step may be ignored. Caution: The parts and screws, and the wiring method of the leads and ferrite cores should be placed exactly the same position as the original otherwise it may cause loss of performance and product safety.
Page 13
Mechanical Disassembly 2. Main board removal Remove 4 screws A(M3X8)and screw B(M4X5) to remove the main board. Main board -13-...
Page 14
Mechanical Disassembly 3. AV panel removal 1. Remove 4 screws A(T3x8) and screw B(M3x6) to remove the AV panel. 2. Remove 6 screws C(M3x7) to remove the AV panel shield. 3. Remove screw D(M3X8) and E(T3X8) to remove the RJ45 holder. 4.
Page 15
Mechanical Disassembly 4. Fans and Optical assembly removal 1. Remove screw A(T3X12) and 2 screws B(T3x8) to remove fan holder and shield. 2. Remove C(M3x8) to remove the connecter. 3. Remove 3 screws D (M3x8) to remove the lamp assembly. 4.
Page 16
3. Remove 2 screws C (T2.5x6.5) to remove the speaker. Lamp duct assembly LCD panel duct assembly Speaker LC-XNS2600 1. Remove 10 screws A (T3x8) to remove the LCD panel duct assmebly. 2. Remove 2 screws B (T2.5x6.5) to remove the speaker. Optical engine duct assembly Speaker...
Page 17
Lamp duct Temperature sensor board (button) LC-XNS2600 1. Remove 2 screws A (T3x8) to remove the bottom duct and the duct shield. 2. Remove 2 screws B (T3x12) to remove lamp cooling fan. 3. Remove 2 screws C (T3x12) to remove the LCD panel cooling fans.
Page 18
Mechanical Disassembly Line filter board and Lamp holder removal 1. Remove 4 screws A (T3x8) to remove the lamp holder and wire socket. 2. Remove 2 screws B (T3x8) and screw C (M4x5) to remove the line filter board. 3. Remove 3 screws D (T3x8) to remove line filter board assembly. 4.
Page 19
Mechanical Disassembly 7 Power supply board removal 1. Remove the temperature sensor switch. 2. Remove screw A (M3x8) to remove the connector to main board. 3.Remove 6 screws B (T3x8) and screw C (M4x5) to remove the power supply board assmebly. 4.
Main parts Cabinet parts Item Parent Name Parent Number ASSY_TOP_COVER_XNS2600 63220026 ASSY_TOP_COVER_XNS3100 63220027 ASSY_TOP_COVER_WNS3200 63220028 FILTER CASE CONTROL KEYPAD 63220030 RC_INLAY_COVER DEC_RING LED_INLAY DECORATION WINDOW RUBBER_FOOT DUST FILTER_SPONGE 63220029 Main board Item Parent Name Parent Number PANEL HOLDER_RJ45 SHIELD_AV_TEMINAL PCBA_RJ45 63730018 PCBA_MAIN BOARD 63730015...
Page 21
63220031 A11 RUBBER FOOT_ADJUST FOOT 63230002 BOTTOM CASE 63220025 STAND SHAFT_ADJUST FOOT 63220033 BOTTOM SHIELD SECURITY HOLDER SPRING_ADJUST FOOT 63210013 Internal Parts( for LC-XNS2600) Item Parent Name Parent Number Item Parent Name Parent Number Item Parent Name Parent Number DUCT_TOP...
Page 22
Main parts Internal parts (for LC-XNS3100/LC-WNS3200) Item Parent Name Parent Number Item Parent Name Parent Number Item Parent Name Parent Number DUCT_TOP HOLDER_AC HOLDER_MAIN POWER DUCT_BOTTOM FUSE SPACER_POWER DUCT_LAMP TOP PCBA_FILTER BOARD 63730014 SHIELD_POWER HOUSE DUCT_LAMP BOTTOM LAMP COVER SWITCH HOLDER_POWER HOUSE SHELD_AV BALLAST...
Page 23
Main parts Project lens and IRIS assembly Item Parent Name Parent Number ASSY_IRIS ASSY_IRIS MOTOR Polarizer lens(IN) Item Parent Name Parent Number LENS,CONDENSER(G) LENS,CONDENSER(B) LENS,CONDENSER(R) -23-...
Page 24
Main parts Flyeye lens Item Parent Name Parent Number INTEGRATO(IN) LENS INTEGRATOR(OUT) LENS Condenser lens(out) Item Parent Name Parent Number LENS,CONDENSER(OUT) -24-...
Page 25
Main parts Optical parts Item Parent Name Parent Number LENS,CONDENSER (IN) LENS,CONDENSER (OUT) LENS,CONDENSER (G) LENS,CONDENSER (B) LENS,CONDENSER(R) C06 ASSY INTERGRATOR LENS INTEGRATOR(IN) LENS INTEGRATOR(OUT) LENS LENS,RELAY (IN) LENS,RELAY (OUT) DICROIC MIRROR (B) DICROIC MIRROR (G) MIRROR (B) MIRROR(R) PRISM UNIT PRISM UNIT PRISM UNIT C16/...
Optical adjustment Before optical adjustment, please remove the top cabinet refer to the "mechanical disassembly" . Tools: a 2 mm six angle wrench and socket screwdriver. Note: due to power failure protection, the projector can not be opened, you do not need to disconnect the connector on the MAIN substrate.
Electrical adjustment Service adjustment menu operation Enter service menu Press and hold MENU and button, service mode menu will appear on screen. Adjustment mode Press MEMU button to select the group and itme, and then press or button to adjust the data. Exit service mode Press POWER button to exit the menu.
Page 30
Electrical adjustment Output Voltage adjustment ADC auto calibration[VGA IN 1] 1.Input 100% color bar to VGA IN 1 terminal. 2.Enter service mode. After replacing the Power Board, perform the Output 3.Select group 260, item 1, change the data from o to 1. voltage adjustment as follows.
Page 31
Electrical adjustment ADC auto calibration[Video] 1 Input 16 steps gray scale signal to VIDEO terminal. 2.Enter service mode. 3.Select group 260, item 1, change the data from o to 1. After calibrating, the data of group 260, item 0 will change to o automatically. If the adjustment above failed, please adjust according to the following steps: Pedestal [VGA IN 1] Pedestal [Component]...
Page 32
Electrical adjustment Pedestal [VIDEO] Common Voltage adjustment 1 Input standard adjust signal to VIDEO terminal. 1 Enter the service adjust mode. 2 Enter the service adjust mode. 2 Select item 9 of Group 90, adjuste the data value until 3 Connect the oscope (+) to TP9087 and (-) to GND. the flicker becomes minimum.
Chassis Block Diagrams System Control Main board O N_ 3 _ 3 V_LAN Q4002 3 .3 V_ LAN AUDI O DC-DC Network P5003 PW_N M CLR TPIN+ IC5004 Audio Input(L/R) TPIN - IC1202 PW _N ET_ H/L 7W 8ohm LAN Control IC PT2830 RJ45 TPO U T+...
Troubleshooting Indicator and projector state Check the indicator to know about the state of projector. Indicator State of projector POWER WARNING (Green/Red/Orange) (Red) The projector is off. (AC power cord not connected). The projector is operating normally. - In standby mode. Press POWER to power on the projector. - When the projector is cool enough, the temperature is restored to the normal value, you can turn on the projector.
Troubleshooting No power Please check as follows: Power supply error I n p u t 2 2 0 V , P o w e r Check if 16V and 6V on Check the fuse and other indicator is off main board is normal c o m p o n e n t s o n p o w e r board.
Troubleshooting No image Please check as follows: Input signal, no image Check LCD driver circuit. Check S16V and the peripheral circuit. Check IC1001,IC8001and the peripheral circuit. Chek IC1001, IC3006 and the peripheral circuit. Check if pin 3/6 of IC3006 has H/V Sync signal. VGA IN 1 input, no image Check IC1001 and the peripheral circuit.
Troubleshooting No sound Please check as follows: 1. Check the connecting wire of speaker. Check if pin 1/2, 43/44 of IC1202 2. Check the speaker. has audio output Check IC1202 has audio output. Check if pin 10/26 of IC1202 has Check if the voltage of L5007 reaches to11V? audio output Check if pin 9 of IC1202 has...