Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for gascraft G1011-NZ
Summary of Contents for gascraft G1011-NZ
- Page 1 Portable BBQ With Side Shelves Model No.G1011-NZ FOR OUTDOOR USE ONLY-OPERATES ON LPG Retain these instructions for future use. Marketed by: Gascraft Products P.O. Box 33-470 Takapuna, Auckland New Zealand IMPORTANT : DO NOT LEAVE THIS BBQ UNATTENDED WHEN LIT AND IN USE...
-
Page 2: General Information
GENERAL INFORMATION If you are unable to correct the leak by tightening the connections, turn off the gas and contact the supplier Gas Installation Code immediately. Always ensure the barbecue is kept away from flammable This BBQ is to be used with LPG for 9Kg LPG cylinder. materials and the gas cylinder clear of any heat source. - Page 3 GENERAL INFORMATION Location of your Barbecue DO NOT use your barbecue in garages, porches, sheds, breezeways, or other enclosed areas. Your barbecue is to be Ensure the barbecue is set up on a level and stable used OUTDOORS. The barbecue is not intended to be surface.
- Page 5 Description Figure Description Figure Q'TY Q'TY Hood Hinge Burner - Right Flame Tamer Hood Firebowl Hood Hinge - Left Handle Cooking grill Cooking Plate Firebowl Hinge Hood Hinge - Right - Left Regulator Bracket Hose assembly Thermometer Clip M6X15 Screw Fire bowl M6 Nut Side Shelf...
- Page 6 STEP 1 M6X15 Screw 4 pcs M6 Nut 4 pcs STEP 2 M6X10 Screw 4 PCS M6 Nut 4 PCS...
- Page 7 STEP 3 M4X10 Screw 2pcs M4 Nut 2pcs STEP 4...
- Page 8 STEP 5 M6X10 Screw 1pcs M6 Nut 1pcs STEP 6 M6X10 Screw 8pcs M6 Nut 8pcs...
- Page 9 STEP 7 M5X35 Screw 4pcs M5 Nut 4pcs STEP 8 M6x15 Screw 4pcs...
- Page 10 STEP 9 M5x10 Screw 4pcs M5 Nut 4pcs STEP 10...
- Page 11 STEP 11 STEP 12 M6X10 Screw 4pcs M6 Nut 4pcs...
- Page 12 STEP 13 M5X10 Screw 2pcs STEP 14 fix the lid with” lid Support Axle and Clip” Clip 2pcs Hinge Axle 2pcs...
- Page 13 STEP 15 STEP 16...
-
Page 15: General Assembly
GENERAL ASSEMBLY If the safety feature activates, the barbecue will operate with reduced output as gas flow is restricted. Connecting & Disconnecting to Gas Source If the Excess Flow Valve is inadvertently activated and the IMPORTANT: Before connecting BBQ is not receiving adequate amount of gas for optimal disconnecting barbecue to gas source, make sure performance, these steps should be taken first to reset the regulator is in ‘LOCK’... -
Page 16: Grill Cooking
Lighting Procedure travels upwards, imparting that unique barbecued flavour. Before lighting your barbecue for the first time, read the instructions fully to ensure the barbecue is assembled Plate Cooking correctly and is ready for use. Remove all point-of-sale The burner heats the plate directly, which then material from the barbecue. -
Page 17: Cooking Surfaces
Fat Fires Any rust that is found that does not come into contact with the food should be treated with a rust inhibitor Empty and clean the fire bowl and grease box of food debris after each cooking session. If the and painted with barbecue paint or a heat resistant barbecue is to be used for large gatherings, it will paint. - Page 18 abrasive s . R emove cooking surfaces and burners Cover the burner with aluminium foil in order to before full cleaning. Do not immerse the gas prevent insects or other debris from collecting in controls or manifold in water. Check burner the burner holes .
- Page 19 Check the gas supply and refill if necessary. Remember to open No Gas or Valve not open the gas valve after maintenance! Check the information in the BBQ manual regarding the “QCC Hand-wheel safety Feature For 9kg LPG Cylinder Only”. Excess Flow Valve Always make sure that the control valve on your cylinder is in the activated...
Need help?
Do you have a question about the G1011-NZ and is the answer not in the manual?
Questions and answers