Setting Trolley Close Position/; Connecting Door Arm; Low Headroom; Standard Lift - Wayne-Dalton Prodrive 3220C Installation Instructions And Owner's Manual

Setting Trolley Close Position/

(Models 9100, 9400, 9600, 5120, 5140 & 9700)
With TorqueMaster® Or Extension Springs
Tools Needed: DETERMINE THE WAYNE-DALTON TRACK
RADIUS BEING USED:
Needle Nose Pliers
FOR MOUNT HOPE AND PENSACOLA
TRACK:
Measure the curved ends of the horizontal
Adjustable Wrench
track to determine if you have a 12" or 15"
radius horizontal track, as shown in FIG. 1.
Ratchet Wrench
FOR PORTLAND TRACK:
The horizontal tracks are stamped with
7/16" Socket
radius on the side of the horizontal track, as
shown in FIG. 1.1.
9/16" Socket
NOTE: If necessary, remove the upper arm
(straight arm) from the trolley, to use the
Hacksaw
lower arm (curved arm). Remove the hairpin
cotter from the clevis pin at the front of
trolley and slide clevis pin out far enough
to slide the upper arm out between the left
and right side of trolley body. Position the
lower door arm so the end with the single
hole lines up with the clevis pin. Slide clevis
pin completely back into trolley and reinstall
hairpin cotter.

LOW HEADROOM:

If you have low headroom track, as shown
in FIG. 1.6 on page 24, then proceed with
"Low Headroom Trolley Positioning Charts"
on page 24.

STANDARD LIFT:

Using the STANDARD LIFT TROLLEY
POSITIONING CHARTS, refer to DIM "X" to
set the distance from header to trolley, as
shown in FIG. 1.2.
NOTE: Depending on your setup, you may
have to cut straight arm to accomplish trolley
settings.
STANDARD LIFT TROLLEY POSITIONING CHART
FOR (MODELS 9100, 9400, 9600, 5120 & 5140)
DIM "X"
11 1/2"
If adjustment of the trolley position is
required, use the close travel adjustment
screw located on the bottom of the opener,
as shown in FIG 1.5 on page 24. A 1/4 turn
equals approximately 1" of trolley travel; turn
clockwise to decrease distance (forward)
and counter-clockwise to increase distance
(forward).
NOTE: Proceed with "Connecting Door Arm
To Door" Step 18, on page 14.
Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need

Connecting Door Arm

10" AND 12" RADIUS
TYPE OF ARM REFERENCE
BEING USED ILLUSTRATIONS
CURVED /
FIG. 1.4
STRAIGHT
Horizontal
Track
12" OR 15"
FIG. 1
TOP VIEW
Clevis Pin
Trolley
Hairpin Cotter
"X"
Top Section
Straight Arm
Curved
Arm
Cut Straight Arm To
Accomplish Trolley
Setting
FIG. 1.3
STANDARD LIFT TROLLEY POSITIONING CHART
FOR (MODELS 9100, 9400, 9600, 5120 & 5140)
14" AND 15" RADIUS
TYPE OF ARM
DIM "X"
BEING USED
CURVED /
13"-15"
STRAIGHT
STANDARD LIFT TROLLEY POSITIONING CHART
FOR (MODEL 9700) 15" RADIUS
TYPE OF ARM
DIM "X"
BEING USED
10 9/16"- STRAIGHT /
14 5/8" CURVED
Horizontal
Track
12"
FIG. 1.1
Stamped 12"
Radius
10", 12", 14", OR 15"
Standard Lift Track
FIG. 1.2
Curved Arm
Straight Arm
Cut Straight Arm To
Accomplish Trolley
FIG. 1.4
REFERENCE
ILLUSTRATIONS
FIG. 1.4
REFERENCE
ILLUSTRATIONS
FIG. 1.3
Setting
23