Subscribe to Our Youtube Channel
Related Manuals for Puretec IMB Series
Summary of Contents for Puretec IMB Series
- Page 1 User Guide IMB Series Manual Backwash Water Filter Systems JUN2020 For correct operation & installation, it is essential to observe these instructions.
-
Page 2: Table Of Contents
Before Installation ..............................6 Positioning the IAB System ...........................6 Assembly .................................6 Dimensions ................................7 Installation ................................8 Performance Data ............................10 Water to be Treated ............................10 Operation ................................10 Maintenance ..............................11 Troubleshooting ...............................12 Warranty ................................13 Installation & Operation Manual Copyright © Puretec Pty Ltd 2020... -
Page 3: Puretec Customer Service
Introduction Puretec Customer Service Thank you for purchasing a Puretec IMB Series Manual Backwash Water Filter System. Your system is a proven performer manufactured from only quality materials and components and will give years of filtered water, if maintained properly. -
Page 4: Warning
130 140 (New Zealand). Clause on the Ownership The contents of this user guide are the exclusive property of Puretec and cannot be reproduced or copied in any form whatsoever. The manual may only be used as a reference tool for the supplied equipment and shall not be submitted to examination by third parties without prior written authorsation by Puretec. -
Page 5: Components
Components Components After opening the box, check the integrity of the equipment and the presence of all the items. IMB25 User Guide Warranty Card IMB Filter System Warranty Card IMB Filter System User Guide IMB50 Warranty Card User Guide IMB Filter System User Guide Warranty Card IMB Filter System... -
Page 6: Before Installation
The permissible limiting values of the environmental parameters for the installation of the IMB System are: Min/Max Ambient Temperature 0 - 40 °C (protect from freezing). Assembly The filter is supplied with the water inlet on the left. Installation & Operation Manual Copyright © Puretec Pty Ltd 2020... -
Page 7: Dimensions
Dimensions IMB25 IMB50 Code Connection IMB25 1" 100 mm 295 mm 225 mm 400 mm (min) 100 mm IMB50 2" 265 mm 361 mm 289 mm 400 mm (min) 109 mm Manual Backwash Water Filter Systems... -
Page 8: Installation
The plumbing system in which the filter is installed and the installation of the filter itself must be carried out in compliance with local laws. Puretec is not responsible for damages to property or persons resulting from the incorrect installation of the filter and/or the installation of the filter in a system not complying with the local laws. - Page 9 Installation • Remove the top and bottom green rings to remove the plastic covers. • Install the filter, ensure that the water is flow direction matches the flow direction arrow as indicated by the arrow stamped on the brass filter head. Make sure there is enough room around the filter so the cover can be removed for easy access.
-
Page 10: Performance Data
Operation Often filters exclusively remove the dirt accumulated in the bowl, without cleaning the cartridge. The Puretec IMB Series guarantees an efficient and thorough cleaning of the filter cartridge too, thanks to its brushing and drainage functionality. 10 Installation & Operation Manual... -
Page 11: Maintenance
Maintenance Filter Cleaning Puretec recommends backwashing the screen every 3-4 days, or at user dicretion, whenever there is a drop in presure. If necessary, backwashing can be repeated. During the backwashing process, the filter discharges some water . This discharge can be run off to a drainage point. -
Page 12: Troubleshooting
Therefore, all preventative maintenance and repair not mentioned in this user guide must be carried out exclusively by Puretec or their agents. In case of doubt, contact Puretec on 1300 140 140 (Australia) 0800 130 140 (New Zealand). Troubleshooting... -
Page 13: Warranty
Applicable to all above, is that the warranties need to be approved by Puretec to ensure product was not incorrectly used, installed or claimed. False and incorrect claims will be pursued at Puretec’s discretion, including chargeable inspection and labour costs incurred. - Page 14 Warranty Warranty/Australia This warranty is given by Puretec Pty Ltd, ABN 44 164 806 688, 37-43 Brodie Road Lonsdale SA 5160, telephone no. 1300 140 140 and email at sales@puretec.com.au. This warranty is provided in addition to other rights and remedies you have under law: Our goods come with guarantees which cannot be excluded under the Australian Consumer Law.
- Page 15 This page was intentionally left blank. Manual Backwash Water Filter Systems...
Need help?
Do you have a question about the IMB Series and is the answer not in the manual?
Questions and answers