Ebyte E180-Z6907A User Manual
  1. Manuals
  2. Brands
  3. Ebyte Manuals
  4. Wireless modules
  5. E180-Z6907A
  6. User manual
Ebyte E180-Z6907A User Manual

Ebyte E180-Z6907A User Manual

Tlsr8269 2.4ghz zigbee soc wireless module
Hide thumbs
Table of Contents

Advertisement

Quick Links

E180-Z6907A User Manual
TLSR8269 2.4GHz ZigBee
SoC Wireless Module

Advertisement

Table of Contents
loading

Related Manuals for Ebyte E180-Z6907A

Summary of Contents for Ebyte E180-Z6907A

  • Page 1 E180-Z6907A User Manual TLSR8269 2.4GHz ZigBee SoC Wireless Module...

  • Page 2: Table Of Contents

    6.5 HEX User instruction set ..........................15 6.5.1 Instruction rule ............................15 6.5.2 Read instruction set ............................. 16 6.5.3 Configuration instruction set ........................18 6.5.4 Network operation instruction set ......................19 6.6 HEX Parameter description ..........................20 Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd.
  • Page 3 7.3.3 Broadcast test .............................. 38 8. FAQ...................................39 8.1 Communication range is too short ........................39 8.2 Module is easy to damage ..........................39 8.3 Bit error rate is too high ..........................40 About us..................................40 Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd.

  • Page 4: Overview

    IEEE802.15.4 standard ISM band. E180-Z6907A was certified by a series of authoritative RF instruments, combined with years of market experience and the actual needs of users in this industry, it integrates the extremely complex communication protocols of wireless products into the built-in SoC, supports serial port transparent transmission mode, It also integrates self-organizing network function, provides multi-channel configurable ADC, IO, PWM interface.

  • Page 5: Device Type Introduction

    The wake-up cycle must be set less than 30 seconds. If you only need to upload data, you can set the wake-up cycle to be greater than 30 seconds or longer to reduce power consumption (default is 5 minutes), such as battery powered sensors. Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd.

  • Page 6: Application

    For 5V TTL, it may be at risk of burning down Working temperature（℃） Industrial design Frequency（MHz） 2405 2480 Support ISM band TX current（mA） Instant power consumption RX current（mA） Sleep current（μA） 16.5 Software shutdown Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd.
  • Page 7 Protocol Zigbee 3.0 Packing Connector 1.27mm Stamp hole TELINK TLSR8269 FLASH 512KB 32KB Core 32 bit MCU Size 11.5*22mm Antenna 50 ohm impedance Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd.

  • Page 8: Size And Pin Definition

    WAKE pin is mainly used to wake up the sleeping terminal. It is high level when power is on. When the pin is pulled low externally, the sleeping terminal device will be woken up. Output UART TX pin Input UART RX pin Reserve，directly suspended Reserve，directly suspended Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd.
  • Page 9 LINK pin shows current network state, high level means access to network Reserve，floated PA0(PWM1) Output PWM output port 1 Reserve，floated Reserve，floated Reserve，floated Input/Outpu Ground, connected to power supply reference ground nRESET Input Reset pin Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd.

  • Page 10: Operation Mode

    Working mode switch pin PD3, internal configuration pull-high resistance input mode, power on default high level, in any mode, when mode switch pin PD3 is pulled low more than 500ms, the module working mode switch, as shown in the figure below: 模式引脚电平脉冲 配置 传输 模式引脚电平脉冲 模式引脚电平 >500ms Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd.

  • Page 11: Transmission Mode

    5.2.2 Data + short address When the output mode is data + short address, after receiving the wireless data, the serial port will output the Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-10...

  • Page 12: Data+Long Address

    When the pin is externally pulled down, the dormant terminal device will continue to be awakened. When the pin is released externally, it will return to high level and enter sleep; Sleep time is determined by the duration of the external Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-11...

  • Page 13: Aux

    ID, the module judges that the data packet is a remote configuration command and executes the corresponding command operation. The data packet will not be output through the serial port. Remote configuration of Sleep-end -device needs to wake up first. Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-12...

  • Page 14: Functional Parameter Description

    For details, please see the corresponding mode function introduction; Output Data output mode of the configuration module:配 mode Transparent transmission; Read/Write Data + short address; 0、1、2、3、4、 Data + long address; Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-13...
  • Page 15 Access/control module duty cycle and period of the Read/Write PWM channel; Read 0～3300mv Read the ADC value of the device, where 0 channel can ADC value read the device power voltage value; Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-14...

  • Page 16: Hex User Instruction Set

    F5 : fixed head LEN: Actual length of DATA CMD: Actual named ID DATA: Actual parameter FF：Command terminator Configuration return：FC CMD STATUS FC: Fixed head CMD: Actual named ID Status: 00 operation succeeded Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-15...

  • Page 17: Read Instruction Set

    Send： FE 01 26 FF transmitting mode Return： FB 26 send_mode Return： FB 26 02 Send： FE 01 27 FF Send：FE 01 27 FF Read data output mode Return： FB 27 out_mode Return： FB 27 00 Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-16...
  • Page 18 Return： FB 36 Uart_holdtime Return： FB 36 64 Read port info. Send： FE 05 37 FF Send： FE 05 37 FF Return： FB 37 01 FE B0 Return： FB 37 Endpoint_info 05 04 Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-17...

  • Page 19: Configuration Instruction Set

    Send：FD 01 30 05 FF after the end-device node loses the Return：FA 30 Return：FA 30 parent node Configure the wireless remote Send：FD 02 31 header FF Send：FD 02 31 A8 8A FF Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-18...

  • Page 20: Network Operation Instruction Set

    Return：FC 40 00 Send：F5 01 40 02 FF Send：F5 01 40 02 FF Leave Network Return：FC 40 00 Return：FC 40 00 Create network Send：F5 01 40 03 FF Send：F5 01 40 03 FF Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-19...

  • Page 21: Hex Parameter Description

    10 bytes. It is recommended to use“FF FF FF FF FF FF FF FF FF FF”10 bytes of "FF" wake up. 6.6.4 Network state nwk_state： 0x00 No network Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-20...

  • Page 22: Network Pan_Id

    Channel The parameters need to be configured before entering the network or establishing a network. 6.6.12 Transmit power txpower：Transmit power level（default 7dBm） Adjustable range -37dbm,-30dbm ,-27.5dbm,-23.3dbm,-18.8dbm,-13.6dbm,-9.5dbm,-4.3dbm,-0.6dbm,5dbm,7dbm txpower Transmit Buad Baud rate Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. power level 4-21...

  • Page 23: Serial Port Baud Rate

    6.6.16 Period of network reconnection after loss of parent node Rejoin period: （1～255）Reconnection period range 1～255 Unit: minute Default 5 minutes 6.6.17 The maximum number of attempts to reconnect Rejoin maxcount: （1～255）Maximum range of reconnections 1～255 times Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-22...

  • Page 24: 18Wireless Remote Configuration Id

    PwmId : Channel ID Channel ID PWM GPIO Port 0x00 PB4 Port 0x01 PA0 Port 0x02 PA3 Port 0x03 PC5 Port start/stop: Start/stop channel PWM output 0xFF Start PWM 0x00 Stop PWM Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-23...

  • Page 25: User Adc Parameter

    0A 1C 21 FE FF 57 B4 14； System transmitting mode 02；Data output mode 00；Network open time FF( coordinator is valid and this module does not support) ；rejoin period 05；rejoin times 05；Wireless ID A8 8A； Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-24...

  • Page 26: Read All Network Parameters

    6.6.27 Set Link key of trust center TrustCentLinkKey：data length of 16 bytes, default key of ZigBee alliance is 0x5A 0x69 0x67 0x42 0x65 0x65 0x41 0x6C 0x6C 0x69 0x61 0x6E 0x63 0x65 0x30 0x39 Take effect once restart Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 4-25...

  • Page 27: Firmware Version Number

    (2) After the serial port is opened, first click “Enter Configuration Mode”, the message box prompts “Enter the configuration status successfully, read parameter successfully”. The main network parameters include: the node type Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-26...
  • Page 28 (you can also use the default value without modifying the parameters). Modify the channel, network PANID and transmit power. After modifying the parameters, click “Write Network Parameters”. ", the message box will prompt "Write parameters successfully". Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-27...
  • Page 29 Mode” again, the message box prompts “Enter the configuration status successfully, read parameters successfully”. It can be seen that the parameters read are the previously modified parameters, indicating that the network parameters are modified successfully. Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-28...

  • Page 30: Join A Zigbee Network Quickly

    7.2 Join a ZigBee network quickly (1) Open the host computer software "E180-Z6907A-Setting v1.2", select the port number and set the serial port baud rate, and open the serial port. Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd.
  • Page 31 The main network parameters include: the node type defaults to the end-device, the channel 11 (default), the PAN ID defaults randomly, and the transmit power is default 0 (7dbm). Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-30...
  • Page 32 PAN ID and transmit channel parameters must be the same as the network to be joined, click "Write network parameters", the message box prompts "Write parameters successfully." Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-31...
  • Page 33 PAN ID and transmit channel parameters are the modified value before.(PAN ID of the established network coordinator). (5) Select the fixed-point networking interface and display the network status as “joined network”, indicates sleep-end-device node has joined the network created by the former coordinator. Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-32...

  • Page 34: Zigbee Network Communication Test

    0). It does not need to be modified at this time. If the end-device communicates with the non-coordinator node, it needs to be modified (modified to the destination node's network local short address), click "write network parameter" after modification. Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-33...
  • Page 35 Input the data to be sent in the sending area, click send, and the received data can be seen in the end-device node message box. （3）Similarly, End-device unicast to Coordinator Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-34...

  • Page 36: Unicast In Long Address Form Between End-Device And Coordinator

    (2) After the target MAC address is configured, the transmission mode needs to be configured. Change the "network address (short address)" to "MAC address", and then write the parameters again. At this time, the target address is configured to unicast in the form of MAC address. Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-35...

  • Page 37: Multicast Test

    "under multicast mode, all nodes with the same group number in the network will receive multicast data", modify the target group number to "5", and then write the parameter, and the message box will prompt "write the parameter successfully". Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-36...
  • Page 38 (3) The end-device receiver enters the configuration mode, changes the network group number to "4", and writes the parameter. At this time, because the network group number is not "5", the coordinator multicast data cannot be received. Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-37...

  • Page 39: Broadcast Test

    (2) Enter the transmission mode, the message box will prompt "enter the transmission mode successfully", and then broadcast data communication, at this time, all nodes in the network will receive data, including the sending node. Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-38...

  • Page 40: Faq

    Please make sure antistatic measure are taken when installing and using, high frequency devices have electrostatic  susceptibility. Please ensure the humidity is within limited range, some parts are sensitive to humidity.  Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-39...

  • Page 41: Bit Error Rate Is Too High

     The extension line and feeder quality are poor or too long can also cause high bit error rate About us Technical support: support@cdebyte.com Documents and RF Setting download link: www.ebyte.com Tel：+86-28-61399028 Fax：028-64146160 Address: Building B5, MouldIndustrialPark,199#Xiqu Ave, West High-tech Zone, Chengdu, 611731, Sichuan, China Copyright ©2012–2019，Chengdu Ebyte Electronic Technology Co., Ltd. 7-40...

Table of Contents