Download Print this page

Troubleshooting - Kyosho EP BLUESTREAK 800 Instruction Manual

Radio controlled electric powered racing boat

Advertisement

ねじ、ナットのゆるみ、老化をチェック。
回転部分にはグリスを塗っておく。
コードが可動部分にこすれたりして破損している
ときは修理する。
サーボのコードや受信機のアンテナ線が破損して
いるときは、使用しているプロポメーカーに修理を
依頼する。
部品が摩耗または破損していないかチェック。
船体の汚れをとる。
船体に入っている水をぬき、よく乾かす。
症  状
スピードコントロールサーボが
動かない。
モーターがまわらない。
モーターはまわるが走らない。
スクリューを手でまわすと重い
    またはまわらない。
スピードコントロールスティ
ックをはなしても船がとまら
ない。
PROBLEM
Speed control servo does
not operate.
Motor does not rotate.
Motor rotates but boat will not run.
When rotating by hand, propeller
feels heavy or does not rotate.
Even when releasing speed
control, boat will not stop.
日常の整備 EVERYDAY MAINTENANCE
故障かなと思う前に
原  因
送、受信機のスイッチがはいっていない。
送信機の電池がない。
配線をまちがえている。
ニカドバッテリーの容量不足。
配線をまちがえている。
コネクターの接触不良。
モーターの故障。
ジョイントがついていない。
または、ビスがゆるんでいる。
回転部分にゴミやホコリがつまっている。
リンケージの調整不良。

TROUBLESHOOTING

CAUSE
Transmitter and/or receiver is not switched on.
Transmitter batteries are weak.
Improper radio installation.
Ni-Cd battery capacity is insufficient.
Improper radio installation.
Loose connectors.
Motor trouble.
Joint is not installed.
Or, screws are loose.
Dirt entered rotating parts.
Improper linkage adjustment.
Make sure screws and nuts are securely tightened
and other parts are not worn.
Grease all rotating parts.
Repair the wiring should cords be damaged or drag
into rotating parts.
Should servo cords and the receiver antenna be
damaged, return them to the manufacturer for repair.
Make sure all parts are neither worn nor damaged.
Remove dirt from the hull.
Draw out water from inside the hull.
対  策
送、受信機のスイッチを入れる。
新しいものに交換する。
プロポの説明書をよく読んでコネクターを
接続する。
ニカドバッテリーを充電する。
説明書をよく読んで配線する。
コネクターのはめこみをきつくする。
モーターを交換する。
ジョイントを止めているビスを
しめる。
ゴミやホコリを取り除きグリスを塗っておく。
プロポのトリムで調整する。
このとき、全開に入らないようなら説明書
を読んでリンケージをもう一度調整する。
REMEDY
Switch on.
Replace with new batteries.
Correct as per radio instruction
manual.
Recharge Ni-Cd battery.
Correct as per instruction manual.
Make connectors tighter (e.g. with
minus screwdriver).
Replace with new motor.
Tighten screws holding joint.
Clean and regrease.
Adjust speed control trim on transmitter.
Should speed controller not return to
neutral, readjust linkages as per in-
struction manual.
19

Advertisement

loading