Page 1
X - S T R E A M S L I D E ™ Assembly & Installation Instructions IMPORTANT THESE INSTRUCTIONS MUST REMAIN WITH THE SLIDE OWNER! 3 0 5 0 A L V E R N O N W A Y •...
Step 10: Connect Water Supply System......15-16 Step 11: Finishing Steps............16 Final Inspection Check List .............16 Slide Care & Maintenance............17 Paver Kit Information.............18 Hardware Kit Information ............19 Exploded View of X-Stream Slide..........20 Parts List (corresponds with exploded view)......21 Inter-Fab Limited Warranty.............22 XS-IM Rev. 7/08 (SBK-XS INSTALL)
IMPORTANT NOTICES TO THE INSTALLER INTER-FAB HIGHLY RECOMMENDS THAT YOU READ THE ENTIRE INSTALLATION MANUAL BEFORE YOU ATTEMPT THE INSTALLATION OF THE X-STREAM SLIDE. YOU MUST USE THE PROVIDED ANTI-SEIZE ON ALL THE BOLTS AND ALL-THREADS OR THE NUTS MAY SEIZE.
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E INTENDED USE INSTRUCTIONS Everyone who uses this slide must know, understand and follow these instructions The ANSI/NSPI-4 2007 standard for above ground pools prohibits the use of slides or diving boards on above ground pools.
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E X-STREAM WATER SAFETY ENVELOPE: DIAGRAM A A minimum water depth of three feet (3') under the exit (NOT TO SCALE) of the slide which increases to a depth of four feet (4') at point A which is located four feet six inches (4'6")
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E SLIDE PLACEMENT DIAGRAM & FOOTPRINT DIAGRAM X-Stream Slide - Left Turn DIAGRAM D (NOT TO SCALE) 3”...
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E SLIDE PLACEMENT DIAGRAM & FOOTPRINT DIAGRAM X-Stream Slide - Right Turn DIAGRAM F (NOT TO SCALE) 3”...
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E X-STREAM SLIDE COMPONENTS IMPORTANT: For a Left Hand Slide, Flume A, B is upper flume, and C, D is the lower flume, in that order.
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E LIST OF REQUIRED TOOLS Tools required for assembly and installation of X-Stream slide: NOTE: USE PROVIDED ANTI-SEIZE ON ALL BOLTS! Hammer 3/8"...
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E STEP TWO: Attach the Ladder to the Entry Section Utilizing hardware kit XS-103-SS, attach the ladder to the entry section on the ground.
Page 11
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E STEP THREE: Attach the Handrails to the Ladder and Entry Section - CONT. Insert the correct length of all-thread into the nuts embedded in the handrails then attach the handrails as illustrated.
Page 12
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E STEP THREE: Attach the Handrails to the Ladder and Entry Section - CONT. Fig.
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E STEP FOUR: Attach the Feet to the Legs TIP: Do not confuse the (4) foot holes at the bottom of the leg with the (4) leg receiver holes at the top.
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E STEP FIVE: Assemble the Flume Sections – CONT. Utilizing hardware kit XS-102-SS, attach the exit section to the lower flume section.
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E STEP EIGHT: Attach the Entry Section & Ladder to the Flume Utilizing hardware kit XS-102-SS, thread the (4) 3/8”...
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E STEP NINE: Anchoring the Slide to the Deck Position the assembled slide on the deck in its correct and final position, then ensure that the long and short legs are plumb by checking each leg with a bubble level on two sides at 90˚...
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E X-STREAM™ SLIDE CARE & MAINTENANCE: Your slide requires periodic maintenance to keep it looking like new. •...
X - S T R E A M ™ S L I D E PAVER KIT INFO – X-STREAM When installing an Inter-Fab X-Stream™ slide using a paver kit, you must ensure that all standard installation requirements are met. The slide must be compatible with the type of pool on the intended installation and all ANSI/NSPI-2003 requirements must be met.
I N S T A L L A T I O N M A N U A L X - S T R E A M ™ S L I D E X-STREAM™ SLIDE HARDWARE KITS XS-101-SS – PVC LEG TO FOOT RECEIVER QTY PART NUMBER COMPONENT DESCRIPTION H-SS 3/8-16X2...
* not pictured HARDWARE NOTE: Use a small dab of NOTES: anti seize lubricant X-Stream slide only comes in Summit Gray (included) on all bolt X-Stream can turn to the right or the left threads. XS-IM Rev. 7/08 (SBK-XS INSTALL)
Inter-Fab, Inc., and expressly does not cover any labor or reinstallation expenses related to the replacement of any and all Inter-Fab products. This limited warranty shall be the sole and exclusive remedy of irrespective of whether the claims are made in contract, tort, warranty, law, equity or by statue.
Need help?
Do you have a question about the X-STREAM SLIDE and is the answer not in the manual?
Questions and answers