Ryobi ECO-2335 User Manual page 22

GB
F D
ADJUSTMENTS
Using the Wrench provided, to loosen and remove bolt.
■
Note: Bolt has right hand threads. Turn bolt
counterclockwise to loosen.
Remove outer washer, outer flange , and wheel.
■
Do not remove spacer, inner flange and inner washer.
Removal of these three parts are not required for
wheel changes.
WARNING
If inner flange, inner washer or spacer has been
removed, replace those parts before placing wheel
on wheel arbor. Failure to do so could cause an
accident since wheel will not tighten properly.
TO INSTALL (Fig. 3)
Unplug your cut-off machine.
■
WARNING
Failure to unplug cut-off machine could result in
accidental starting causing possible serious
personal injury.
Inspect the replacement wheel for defects such as
■
cracks, chipping, and correct speed rating. If defects
are found or the speed rating is not greater than
4800min , stop using the wheel. Select another wheel.
-1
Clean debris from the inner washer and inner flange.
■
Place new wheel over spacer, then place both on
■
wheel arbor against inner flange.
Clean outer flange, then align flats with flats on wheel
■
arbor and slide it onto arbor until it is flushed against
wheel.
Place recessed side of outer washer against arbor,
■
then insert wheel bolt into threaded end of wheel arbor.
Start threads and turn bolt clockwise to snugly
■
tighten.
Pull the spindle lock button and rotate bolt until spindle
■
being locked. This will prevent shaft from rotating.
Using the wrench provided, securely tighten wheel bolt.
■
Note: Bolt has right hand threads. Turn bolt clockwise
to tighten.
WARNING
Do not overtighten wheel bolt. Overtightening
can cause the new wheel to crack, resulting in
premature failure and possible serious personal
injury.
E I P NL S DK N FIN
English
PROTECTION GUARD
In order to avoid spark splashing, under the operational
condition, loose the screw and adjust angle of the
protection guard.
ADJUSTABLE FENCE (Fig. 4)
The adjustable fence is located at the rear of your cut-off
machine. It is used along with the vice clamp to provide a
clamp for holding your workpiece securely when making
cuts. It also makes your cut-off machine more versatile.
The fence can be rotated to obtain cutting angles from 0°
to 45° (L&R). It can also be moved back to allow greater
cutting widths in thin stock, or moved forward to allow
greater cutting depths in tall or thick stock.
CUTTING ANGLE ADJUSTMENT (Fig. 4)
Unplug your cut-off machine.
■
WARNING
Failure to unplug cut-off machine could result in
accidental starting causing possible serious
personal injury.
Loosen the fence quick lock, by using the wrench
■
supplied. Then loosen the fence bolt to secure the
adjustable fence.
Rotate fence until the desired angle of cut on the
■
scale is aligned with the indicator in machine base.
For precise cuts, check the angle of cut for the fence
■
against the abrasive wheel with a protractor, bevel
square, or other similar device.
Tighten the fence quick lock, by using the wrench
■
supplied, then securely tighten fence bolt. Return
wrench to its storage area in the base.
This will secure the fence in place at desired angle.
■
ADJUSTING WIDTH OF CUT (Fig. 5-6)
Unplug your cut-off machine.
■
WARNING
Failure to unplug cut-off machine could result in
accidental starting causing possible serious
personal injury.
The default space between the vice and the fence is
■
0 mm min. to 170 mm max. By following the below
adjustment procedures, it is possible to increase that
distance so that the vice is between 35 mm and
205 mm or 70 mm and 240 mm from the fence.
16
GR H CZ RUS RO PL