Ryobi ECO-2335 User Manual page 19

GB
F D
RULES FOR SAFE OPERATION
NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
■
Normal sparking of the motor could ignite fumes.
INSPECT TOOL CORDS PERIODICALLY and if
■
damaged, have repaired at your nearest Ryobi
Authorized Service Center. Stay constantly aware
of cord location and keep it well away from the
rotating wheel.
USE OUTDOOR EXTENSION CORDS. When tool is
■
used outdoors, use only extension cords with
approved ground connection that are intended for use
outdoors and so marked.
DO NOT USE TOOL IF SWITCH DOES NOT TURN
■
IT ON AND OFF. Have defective switches replaced
by an authorized service center.
KEEP TOOL DRY, CLEAN, AND FREE FROM OIL
■
AND GREASE. Always use a clean cloth when
cleaning. Never use brake fluids, gasoline, petroleum-
based products, or any solvents to clean tool.
ALWAYS SUPPORT LONG WORKPIECES.
■
To minimize risk of tipping machine, always support
long workpieces.
BEFORE MAKING A CUT, BE SURE ALL
■
ADJUSTMENTS ARE SECURE.
ALWAYS USE THE VICE CLAMP to secure the
■
workpiece.
NEVER TOUCH WHEEL or other moving parts
■
during use.
NEVER START THE CUT-OFF MACHINE WHEN THE
■
WHEEL IS IN CONTACT WITH THE WORKPIECE.
NEVER cut more than one workpiece at a time.
■
DO NOT STACK more than one workpiece on the
machine base at a time.
NEVER PERFORM ANY OPERATION "FREEHAND".
■
Always secure the workpiece to be cut in the vice.
NEVER hand hold a workpiece. Workpiece will
■
become very hot while being cut.
NEVER reach behind, under, or within three inches of
■
the wheel and its cutting path with your hands and
fingers for any reason.
NEVER reach to pick up a workpiece, a piece of
■
scrap, or anything else that is in or near the cutting
path of the wheel.
AVOID AWKWARD OPERATIONS AND HAND
■
POSITIONS where a sudden slip could cause your
hand to move into the wheel. ALWAYS make sure
you have good balance.
NEVER stand or have any part of your body in line
■
with the path of the wheel.
E I P NL S DK N FIN
English
ALWAYS release the power switch and allow the
■
wheel to stop rotating before raising it out of the
workpiece.
DO NOT TURN THE MOTOR SWITCH ON AND
■
OFF RAPIDLY. This could cause the wheel to loosen
and could create a hazard. Should this ever occur,
stand clear and allow the wheel to come to a
complete stop. Disconnect your cut-off machine
from the power supply and securely retighten the
wheel arbor bolt.
REPLACEMENT PARTS. All repairs, whether
■
electrical or mechanical, should be made at a Ryobi
Authorized Service Center.
WARNING
When servicing use only identical Ryobi
replacement parts. Use of any other parts may
create a hazard or cause product damage.
IF ANY PART OF THIS CUT-OFF MACHINE IS
■
MISSING or should break, bend, or fail in any way,
or should any electrical component fail to perform
properly, shut off the power switch, remove the
machine plug from the power source and have
damaged, missing, or failed parts replaced before
resuming operation.
MAKE SURE THE CUT-OFF WHEEL IS SECURELY
■
MOUNTED as described in the operating instructions
before connecting the tool to a power supply.
Do not tighten wheel excessively, since this can
cause cracks.
CHECK THE WHEEL FOR FISSURES AND
■
CRACKS, and test for normal operation prior to use.
ONLY USE A CUT-OFF WHEEL RATED FOR
■
4800 min- 1
dry place with little temperature variation.
ALWAYS EASE THE ABRASIVE WHEEL AGAINST
■
THE WORK PIECE when starting to cut. A harsh
impact can break the wheel.
BEFORE CUTTING, press the trigger switch and
■
allow the cut-off wheel to reach full speed before
cutting.
MAKE SURE THE WORK AREA HAS AMPLE
■
LIGHTING to see the work and that no obstructions
will interfere with safe operation BEFORE performing
any work using your cut-off machine.
DO NOT OPERATE THIS TOOL WHILE UNDER
■
THE INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
13
GR H CZ RUS
OR GREATER. Always store wheels in a
RO PL