Related Manuals for Hayter Harrier 48 Autodrive VS ES IS
Summary of Contents for Hayter Harrier 48 Autodrive VS ES IS
- Page 1 Harrier 48 Autodrive VS ES IS CODE476A OPERATOR MANUAL Original Version (EN) From Serial Number: 404000000 and Up Issued: 28/01/2019 Part number: 3428-780 Rev B...
-
Page 3: Table Of Contents
CONTENTS Introduction Before Operation continued Adjusting the Cutting Height Safety 6 - 9 Non Grassed Areas General Safety Controls Safety Alert Symbol Before Mowing Before Operation Safety 6 - 7 Battery Specifi cation - General Safety Battery Charge Gauge - Fuel Safety When to Charge the Battery Pack During Operation Safety 7 - 8... - Page 4 CONTENTS Maintenance continued Blade Sharpening Clutch Cable Adjustment Securing Nuts & Bolts Rear Defl ector Carburetor Adjustments Blade Brake Test Lubrication Battery Disposal Directive Lithium-Ion Battery Pack Disposal Storage 25 - 26 Storage Safety Preparing the Mower for Storage Storage Battery Pack &...
-
Page 5: Introduction
This mower is designed solely for use in a domestic grass cutting environment. Use in any other way is considered as contrary to the intended use. Hayter Limited reserves the right to amend product specifi cations without prior notifi cation. -
Page 6: Safety
SAFETY General Safety Failure to comply with these instructions may result in contact with the moving blade, causing serious personal injury or death. injury. This mower has been designed in accordance with EN - Shut off the engine, wait for all moving parts to ISO 5395-2:2017. -
Page 7: Fuel Safety
3 seconds. If not, stop using your mower manufacturer’s recommended parts when • Do not handle fuel when smoking or around an immediately and contact a Hayter Authorised necessary. open fl ame or sparks. Service Dealer. •... -
Page 8: After Operation Safety
• Remove the electric start button when the mower Hayter replacement parts and accessories. is not in use. 2. That the extension cord is properly wired and in good electrical condition; and •... -
Page 9: Safety & Instructional Decals
Please ensure all Safety Decals are secured on the mower before using the product. If any of the decals are missing or not secure, do not use the mower, contact your Authorised Hayter Service Dealer for replacements. WARNING: Improper maintenance, use of non-conforming spare parts, or the removal or modifi cation of the Safety Decals may cause death or serious injury. -
Page 10: Product Overview
PRODUCT OVERVIEW PRODUCT SPECIFICATION Code 476A Model Harrier 48 Autodrive VS ES IS Weight (Net) 43.8 kg Length 1562 mm Width 532 mm Height 1039 mm Width of Cut 480 mm Height of Cut 13 - 60 mm Engine Briggs & Stratton® Engine Type 675EX InStart™... -
Page 11: Setup
Check that the following items have been supplied correctly. without oil or fuel. The engine must be fi lled with • If a cable is damaged, contact a Hayter Authorised the correct grade of oil and fuel before starting the Service Dealer. Engine Handbook engine. -
Page 12: Engine Detail
SETUP Engine Detail that the oil level is at the top of the full indicator (2) First Time Battery Charging on the dipstick. NOTE: Disconnect the spark plug lead and remove Remove the terminal strip from the battery before • If the oil level on the dipstick is too low, the electric start button before performing any inserting into the charger for the fi... -
Page 13: Before Operation
fi ll above the bottom of the fuel (Refer fi g.7) Fuel stabiliser and engine oil are both available to tank neck. purchase from your Authorised Hayter Service Dealer. 111-9367 - Lawnmower Oil SAE 30 Hayter 3. Reinstall the fuel cap. 111-9368 - Premium Fuel Treatment Hayter (Refer fi... -
Page 14: Before Operation Continued
BEFORE OPERATION Adjusting the Cutting Height Non Grassed Areas mower blade could become dangerous projectiles. Inspect the area for hidden obstructions which when WARNING: Adjusting the cutting height may bring When moving the mower across non-grassed areas, contacted by the blade could risk health and safety you into contact with the moving blade, causing stop the engine and set the mower to the maximum or result in damage to the mower. -
Page 15: Battery Specifi Cation
BEFORE OPERATION Battery Specifi cation When to Charge the Battery Pack • Red light indicates battery pack is charging normally. WARNING: Improper use of the battery and Lithium-Ion Battery • Green light indicates battery pack is fully charger can result in an electrical shock, fi re or charged. -
Page 16: During Operation
If the engine does not start after repeated attempts, the engine should shut off and the blade should stop the required direction. contact your local Hayter Authorised Service Dealer within 3 seconds. If they do not, stop using your or go to briggsandstratton.com. -
Page 17: Vari-Pitch™ Cutting Technology
Allow through the grass bag. To empty the grass bag, Authorised Hayter Service Dealer. the grass clippings to dry out and then mow the area pour out the grass clippings and shake the grass bag at the maximum height of cut setting with the grass vigorously to clean the airways. -
Page 18: After Operation
• Stay in the operating position (behind the handle) from the mower. If a cable is damaged, contact a Hayter Authorised when the engine is running. Service Dealer. 10. Start the engine and run it for a few minutes to dry •... -
Page 19: Maintenance Schedule
MAINTENANCE SCHEDULE Note: Determine the left and right sides of the mower from the normal operating position. Recommended Maintenance Schedule Maintenance Service Interval Maintenance Procedure Before each use or daily Check the engine oil level. Clean grass clippings and dirt from under the mower. Check the condition of guards and safety devices. -
Page 20: Maintenance
MAINTENANCE Preparing for Maintenance the fi lter. Pressurised air can damage the fi lter and solvents will dissolve the fi lter. IMPORTANT: Before tipping the mower to change the oil or replace the blade, allow the fuel tank to run 1. -
Page 21: Changing The Engine Oil
MAINTENANCE Changing the Engine Oil 9. Wait for the oil to settle in the engine. Servicing the Spark Plug 10. Wipe the dipstick clean with a clean cloth. NOTE: Run the engine a few minutes to warm the Improper maintenance, use of nonconforming 11. -
Page 22: Remove & Replace The Blade
If you are uncomfortable (Refer fi g. 31) performing this procedure or do not have a torque wrench, contact a Hayter Authorised Service Dealer. Blade Sharpening WARNING: The blade is sharp; contacting the blade A slightly worn blade may be re-sharpened. Both blade can result in serious personal injury. -
Page 23: Clutch Cable Adjustment
60 mm from the handle. you release the engine stop lever, contact a Hayter or modifi cation of the rear defl ector may cause death Authorised Service Dealer. -
Page 24: Lubrication
MAINTENANCE Lubrication • The crossed-out bin symbol is a reminder to follow Please contact your local authority or dealer to ask these points. for further details regarding the correct method of Lubricate the wheel bearings, pivot points and linkages disposal. (Refer fi... -
Page 25: Storage
STORAGE Storage Safety it is suffi ciently dry. (Refer fi g.38) • Remove the electric start button. Always shut off the mower, wait for all moving parts Battery Pack & Charger Storage • Disconnect the wire from the spark plug. to stop, remove the electric start button and allow the mower to cool before adjusting, servicing, cleaning, or When not in use, disconnect the battery and store in... -
Page 26: Removing The Mower From Storage
STORAGE Removing the Mower from Storage • Check and tighten all fasteners. • Check the battery gauge and charge if required. Refer to Before Operation - How to Charge the Battery Pack. • Install the electric start button. • Remove the spark plug and spin the engine rapidly, by holding the engine stop lever against the handle, followed by pushing the electric start button, to blow the excess oil from the cylinder. -
Page 27: Trouble Shooting
TROUBLE SHOOTING PROBLEM CAUSES CORRECTIVE ACTION PROBLEM CAUSES CORRECTIVE ACTION Engine stop lever released Operate engine stop lever Undulating ground conditions Change direction of travel Electric start button removed Insert electric start button Blade worn Sharpen blade Engine will not turn Uneven cut over Incorrect oil level... -
Page 28: Warranty
90 Day Warranty – Commercial Use Hayter Limited warrants to the original purchaser that this unit shall be free from defects in material and workmanship, under normal, residential use, for a period of fi ve years from the date of purchase or, if used commercially, for a period of 90 days from the date of purchase. -
Page 29: Eu Privacy Statement
To do so, please contact us by email at legal@toro.com. If you have concerns about the way in which Hayter Ltd has handled your information, we encourage you to raise this directly with us. Please note that European residents have the right to complain to your... -
Page 30: Notes
NOTES NOTES... - Page 32 Hayter Limited Spellbrook, Bishop’s Stortford, Herts CM23 4BU England Customer Care Help line: 0800 616 298 www.hayter.co.uk...