LIMITED WARRANTY Hayter Limited warrants to the original user / purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of three years from the date of purchase. The manufac- turers of the engine and battery pack system (where applicable) furnish their own warranty and services are pro- vided through their authorised network (Refer to “Engine/Battery Pack Warranty Statement”).
CONTENTS LIMITED WARRANTY INTERNATIONAL PICTORIALS OWNER’S INFORMATION SAFE OPERATION PRACTICES ASSEMBLY OPERATION MAINTENANCE TROUBLE SHOOTING CHART INTERNATIONAL PICTORIALS Bystanders Away. Read User Instructions WARNING: When you hear the audible alarm it is time to empty the grass bagger. Before Operating This Machine. IMPORTANT: The following pictorials are lo- Control And Operating Pictorials WARNING: Do Not Use This Machine On...
OWNER’S INFORMATION Thoroughly inspect the area where the nor allow anyone near the machine while in equipment is to be used and remove all ob- operation. jects which may be thrown by the machine. Know your product: If you understand the unit 10.
ASSEMBLY 6. Remove the adhesive backing from the hub 3. Fasten the black cable 8 to the negative (–) cover (3) that was set aside earlier. Attach terminal with the fasteners (6) and (7). the hub cover (3) to the center of the steer- All fasteners are in the parts bag.
OPERATION How To Reset The Service Light Before you leave the operator’s position, make sure the blade(s) has stopped rotating. To alert the operator that scheduled service is due, 4. Before you ride the unit across a sidewalk or the service light will automatically come ON. After a road, move the blade rotation control (1) NOTE: Illustrations and pictorials begin on the scheduled service is performed, the service...
Page 16
position (2). The transmission is now con- 3. Move the lift lever to a height of cut position. How To Empty The Grass Bagger nected and ready to operate. In high or thick grass, cut the grass in the (Figure 32) highest position first and then lower the 1.
4. Turn the ignition key to the START position. Inspect Blade (Figure 10) 2. (Figure 11 ) Move the blade rotation control to the DISENGAGE position (1). NOTE: If the engine does not start after WARNING: Before you inspect or four or five tries, move the throttle control 3.
6. To check the adjustment, drive the unit. If the How To Remove The Battery (Figure 6 ) 4. (Figure 16) Move the lift lever (1) to the adjustment is correct, the unit will now go level adjustment position (2). To charge or clean the battery (1), remove the into REVERSE.
Page 19
and then back between the stack pulley and DISENGAGE position. WARNING: Never store the grass the steering plate (3). bagger with grass clippings in the 2. Move the lift lever (2) to the level adjust- 10. Remove the motion drive belt. A correct re- bags.
TROUBLE SHOOTING CHART PROBLEM: The engine does not run 2. Raise the height of cut. smooth at fast speed. 3. Replace or sharpen the blade(s). 1. Replace the spark plug. 4. Move the shift lever to a slower speed. 2. Adjust the throttle control. 5.
Page 39
CODE145S REPAIR PARTS MOWER SUSPENSION ASSEMBLY Description Part No. Description Part No. Assembly, Lift Arm MU95233–853 Grip MU94496 Screw, 1/2–13x1.50 MU711917 PTO Handle MU690126 Nut, 1/2–13 Lock MU711918 Paddle, Switch MU95284 Bracket. Lift Link MU94262–853 Screw, Thread Form MU711621 Washer, Flat MU711617 Bracket, PTO MU94018–853...
Page 40
CODE145S REPAIR PARTS ENGINE AND CONTROL ASSEMBLY REF. CHASSIS FRONT PG. (HOOD) REF. DETAIL ’A’ REF. CHASSIS FRONT PG. (DASH & SUPPORT ) REF. REF. KEY #1 SUB. ASSY. FRAME PG. (FRAME) REF. SUB. ASSY. FRAME PG. (FRONT AXLE ASSY.) INSET ’A’...
Page 41
CODE145S REPAIR PARTS ENGINE AND CONTROL ASSEMBLY Description Part No. Description Part No. 15.5HP (See Engine Manual) Engine Gas Line Tubing 16 In. MU41007 –– Clip, Speed MU94951 Cable Tie MU57444 Engine Bolt 3/8x1.25 MU0025X7 Clamp, Fuel Line Yellow MU336890 Muffler MU94654 Screw, 1/4–20x.50...
Page 52
Übereinstimmungs–Bescheinigung Declaração de conformidade Certificate of conformity Konformitetsintyg Certificat de conformité Konformitetserklæring Certificato di conformità Overensstemmelseserklæring Vaatimustenmukaisuusilmoitus Certificado de conformidad Conformiteitsverklaring Der Unterzeichnete / I the undersigned / Le soussigné / Il firmatario / El abajo firmante / Ondergetekende / O abaixo assinado / Undertecknad / Undertegnede / Undertegnet / Allekirjoittanut MURRAY, INC.
mit den Vorschriften der Richtlinie 84/538 EWG übereinstimmt / conforms to the specifications of Directive 84/538 EEG / est conforme aux spécifications de la directive CEE 84/538 / è conforme alle specifiche della direttiva CEE 84/538 / se conforma a las especificaciones de la directiva CEE 84/538 / in overeenstemming is met de specificaties van de Richtlijn 84/538 EEG / obedece as especificações da diretiva 84/538 C.E.E.
Page 54
EG–Konformitätserklärung entsprechend der Richtlinie 98/37/EG entsprechend der EG–Richtlinien 89/336 EC Certificate of Conformity conforming to Directive 98/37/EC conforming to EEC Directives 89/336 Déclaration de conformité pour la CEE conforme à la directive 98/37/CE conforme aux directives CEE 89/336 Certificato di conformita’ comunitario Declaración de Conformidad según la directiva 98/37/CE según las directivas de la CEE 89/336...
Page 55
219 FRANKLIN ROAD, BRENTWOOD, TN USA 37027 erklären in alleiniger Verantwortung, daß das Produkt declare in sole responsibility, that the product déclarons sous notre seule responsabilité que le produit 40377x11B (CODE145S) dichiariamo sotto la nostra piena responsabilità che il prodotto declaramos bajo responsabilidad propia que el producto verklaren enig in verantwoording, dat het produkt declaramos com responsabilidade própria que o produto...
Page 56
Zur sachgerechten Umsetzung der in den EG–Richtlinien genannten Sicherheits– und Gesundheitsanforderungen wurde(n) folgende Norm(en) und/oder technische Spezifikation(en) herangezogen: BS EN 386:1997, BS EN 1033:1996 und/oder BS EN 1032:1997 To effect correct application of the safety and health requirements stated in the EEC Directions, the following standards and/or technical specifications were consulted: BS EN 386:1997, BS EN 1033:1996 and/or BS EN 1032:1997 Pour mettre en pratique dans les règles de l’art les prescriptions en matière de sécurité...