Do you have a question about the Washlet S400 SW563 and is the answer not in the manual?
Questions and answers
Dieter Grotheer
May 19, 2025
Despite raising the temperature in the remote control the water remains cold.
1 comments:
Mr. Anderson
May 24, 2025
The water may still be cold despite raising the temperature on the remote control for the following reasons:
1. The water temperature setting may still be set to "off" or "low." Recheck and adjust it using the remote control. 2. The residual water inside the unit may be frozen, preventing proper heating. Warm the toilet interior. 3. There may be a blockage in the water supply filter. Clean the filter.
Is the outlet loose? ● Is your Washlet operating differently than usual? ● * In case anything is abnormal, contact TOTO USA to prevent a fire or an electrical shock. ✲ Thank you for your recent purchase of the TOTO ®...
Important Safety Instructions DANGER Avoid damaging the electrical cord or toilet seat cord. Be sure to read the following safety instructions and use the product only as described in this Do not crack, bend, twist or pull the cords. manual. Please follow basic safety instructions to ensure the safe use of your product. Do not treat or heat the cords or place heavy objects on top of them READ ALL INSTRUCTIONS BEFORE USING...
Page 3
To reduce the risk of burns, electrocution, WARNING WARNING fire or injury to persons: 1. Close supervision is necessary when this product is used by, on, or near children or invalids. Use only a mild dish detergent diluted with water to clean your Washlet. Do not use the folloing to clean the Washlet.
Operational Instructions Tips for Using the Washlet ® Always follow these precautions to ensure the safe use of your product. Protect the environment and reduce the use of water and electricity. Do not wipe the Washlet, toilet seat Do not expose to direct sunlight. Use the timer energy Use the Auto energy or toilet lid with a dry cloth, toilet...
Performance Features Washlet Functions Page Energy-saving features Page Rear cleansing The wash alternates between a gentle spray and a forceful Timer energy saver Once set, the toilet seat heater will shut off at the same 21, 22 spray 70 times per second for a thorough rear wash while time every day and save power.
Names of parts Main unit display Main unit controls Remote control the buttons have imprints (bumps) for those with impaired vision. With the cover closed With the cover open...
Before Using the Washlet ® Insert the plug into the wall outlet. Opening the water shut-off valve and the junction valve. Please turn on the junction valve with a flathead screwdriver. Preparation Check Putting batteries in the remote control. Check the "Main unit display". ➀...
How to Use the Washlet ® Drying Standard method of use Standing in front of the toilet The toilet lid will open automatically. (Page 17, Auto open/close) Sit on the toilet seat. The seated sensor will go on and all of the functions will be available. ●...
For Best Results Opening and closing the toilet seat and lid There are two ways to open and close the toilet seat and lid: Remote open/close and Auto open/close. Adjusting the Temperature Using the remote open/close on the toilet seat and lid You can adjust the temperature of the spray water, the toilet seat and the dryer with the remote control.
When sitting on the toilet seat Flushing the toilet Move at least 1 ft. (30 cm) There are two ways to flush the toilet: Remote control flushing and Auto flushing . from the toilet after using the Flushing the toilet using remote control toilet.
To Conserve Energy While standing in front of the toilet Someone must stand in front of the toilet for at least six seconds for the automatic flush Saving power with the timer energy saver to work. The timer energy saver… After urinating, move at least 1 ft.
Turning off the Timer energy To turn off the auto energy saver. saver Press the button. Press the button until the "TIMER" and "SAVING TIME" Auto energy saver will be turned off. display turn off. The word "AUTO" will disappear from the remote display. Energy saving is turned off.
Caring for your Washlet ® Daily care and maintenance Cleaning the Washlet, toilet seat and lid Before cleaning the Washlet ® Wipe with a soft, damp cloth. Each component can be disassembled for a thorough cleaning. Please dampen a soft cloth with water and wipe these surfaces after wringing well.
The toilet lid can be removed from the toilet seat. Thorough Cleaning of the Product [Removing the lid] [Reattaching the lid] Cleaning the Washlet main unit, the toilet seat and lid Place your finger on the seat lock on Align the toilet lid with the the right side and move the hinge toilet seat from the left.
Cleaning the gaps between the Washlet main unit and the toilet Cleaning the deodorizer filter (About once a month) (About once a month) ● If an odor is smelled, please remove the main unit and clean the deodorizer filter. ● The main unit can be removed to clean the upper surface of the toilet and the lower surface of the main unit.
Cleaning the water supply filter To access the “junction valve” filter, the junction valve cover must be removed. Use a large flathead screwdriver or coin and turn the valve cover counter-clockwise. ● If you feel as though the water pressure for washing has weakened, please clean the water Place a container underneath the junction valve.
Page 17
Prevention of damage due to frozen Press the button once more. (The wand will retract.) Push the water drain valve (with water filter) into water pipes place and tighten securely with a flathead screwdriver. When freezing is anticipated Caution Tighten the water drain valve (with Please warm the bathroom interior when the ambient temperatures are expected to be sub-freezing.
Please check the following before calling for service. If that doesn't solve the problem, please Call TOTO U.S.A., Inc. Technical Support at (888) 295-8134 ❈ The drain lever will not work unless the main unit is removed.
Page 19
● If odor is still a problem even after cleaning the deodorizer filter, call When the seat sensor functions, it runs the TOTO technical support. After sitting on the water to prepare to spray warm water. toilet seat, water —...
Page 20
Auto open/close Automatic toilet flushing Problem Possible Cause Solution Problem Possible Cause Solution Is the auto open/close set to "off?" (When set to Push the Auto on/off open/close Is the auto toilet flush set to "off?" (When set to Push the Auto on/off Flush button on button on the remote control and set it the remote control and set it to "on."...
Page 21
Automatic toilet flushing Remote control opening/closing of toilet seat and lid Problem Possible Cause Solution Problem Possible Cause Solution Is clothing covering the seat sensor or the Please move the clothing out of the Are the batteries dead? Please replace the batteries with new way and remove any debris, drops of ones.
Need help?
Do you have a question about the Washlet S400 SW563 and is the answer not in the manual?
Questions and answers
Despite raising the temperature in the remote control the water remains cold.
The water may still be cold despite raising the temperature on the remote control for the following reasons:
1. The water temperature setting may still be set to "off" or "low." Recheck and adjust it using the remote control.
2. The residual water inside the unit may be frozen, preventing proper heating. Warm the toilet interior.
3. There may be a blockage in the water supply filter. Clean the filter.
Check all these factors to resolve the issue.
This answer is automatically generated
How can I replace the spray heater