Baroness LM315GC Owner's Operating Manual
  1. Manuals
  2. Brands
  3. Baroness Manuals
  4. Lawn Mower
  5. LM315GC
  6. Owner's operating manual

Baroness LM315GC Owner's Operating Manual

Riding greens mower (diesel model)
Hide thumbs Also See for LM315GC:
Table of Contents

Advertisement

Quick Links

Download this manual
Riding Greens Mower (Diesel Model)
Owner's Operating Manual
Serial No.
LM315GC：31208-
"Required reading"
Read this manual and the Owner's Manual for the engine before using the machine.
Original Instructions Ver.3.4

Advertisement

Table of Contents
loading

Related Manuals for Baroness LM315GC

Summary of Contents for Baroness LM315GC

  • Page 1 Riding Greens Mower (Diesel Model) Owner's Operating Manual Serial No. LM315GC：31208- "Required reading" Read this manual and the Owner's Manual for the engine before using the machine. Original Instructions Ver.3.4...
  • Page 2 LM315GC Greeting Thank you for purchasing the Baroness product. This manual describes the proper handling, adjustment, and inspection of your product. We hope you will use the product safely, and take advantage of its best performance. Keeping The Owner's Operating...
  • Page 3 The operator is responsible for operating the product properly and safely. Maintenance should only be performed by a certified specialist. If you have any questions concerning maintenance or genuine parts, please contact a Baroness dealer or Kyoeisha. When making inquiries about the product, please specify the product's model designation and serial number.
  • Page 4 When replacing parts, be sure to use genuine Baroness parts or parts designated by Kyoeisha. Note that the Baroness product warranty may not apply to defects caused by the use of parts from other companies. Prior to use, carefully read the following manuals to thoroughly understand the contents for safe and correct operation.

  • Page 5: Table Of Contents

    LM315GC Contents Safety .............. Page 1-1 Safe Operating Practices .......Page 1-2 Disposal ............Page 2-1 Recycle and Waste Disposal ......Page 2-2 Product Overview .......... Page 3-1 Specifications ..........Page 3-2 Names of Each Section ......... Page 3-4 Regulation Decals ..........Page 3-4 Safety Signs and Instruction Signs ....
  • Page 6 LM315GC Contents...

  • Page 7: Safety

    LM315GC Safety Safe Operating Practices ...... Page 1-2 Training ..........Page 1-2 Preparation ..........Page 1-2 Operation ..........Page 1-3 Maintenance and Storage ..... Page 1-4 Page 1-1...

  • Page 8: Safe Operating Practices

    LM315GC Safety Failure to adequately follow these safety Never allow children or people unfamiliar precautions may cause an accident resulting in with these instructions to use or service the injury or death. machine. Local regulations may restrict the age of the...
  • Page 9 LM315GC Safety Add fuel before starting the engine. Never Never operate across the face of the remove the cap of the fuel tank or add fuel slope, unless the machine is designed for while the engine is running or when the this purpose.
  • Page 10 LM315GC Safety Never operate while people, especially Maintenance and Storage children, or pets are nearby. Disengage drives on level ground, lower the Slow down and use caution when making attachments, set parking brake, stop engine turns and crossing roads and sidewalks.
  • Page 11 LM315GC Safety When checking the hydraulic circuit for pinhole leaks or oil leakage from nozzles, do not use your hands. Use items such as paper or corrugated cardboard to find leakage points. Be extremely careful with high-pressure oil as it may pierce your skin, resulting in an injury.
  • Page 12 LM315GC Safety Page 1-6 Safe Operating Practices...

  • Page 13: Disposal

    LM315GC Disposal Recycle and Waste Disposal ....Page 2-2 About Recycle ........Page 2-2 About Waste Disposal ......Page 2-2 Page 2-1...

  • Page 14: Recycle And Waste Disposal

    LM315GC Disposal Recycle and Waste Disposal About Recycle Recycling battery etc. is recommended for environmental conservation and economical use of resources. It may be required by local laws. About Waste Disposal Make sure that waste generated when servicing or repairing the machine is disposed of in accordance with local regulations.

  • Page 15: Product Overview

    LM315GC Product Overview Specifications ........Page 3-2 Specifications .........Page 3-2 Sound Pressure Level ......Page 3-3 Sound Power Level ....... Page 3-3 Vibration Level ........Page 3-3 Carbon Dioxide (CO2) Emissions Measurement .........Page 3-4 Names of Each Section ......Page 3-4 Regulation Decals ........Page 3-4...

  • Page 16: Specifications

    LM315GC Product Overview Specifications Specifications Model LM315GC (for greens) LM315GC (for tees) LM315GC (for fields) Total length 84.65 in 215 cm ← ← Dimens Total width 79.92 in 203 cm ← ← ions 51.97 - 132 - 141 Total height Steering wheel ←...

  • Page 17: Sound Pressure Level

    LM315GC Product Overview 0 - 9.32 0 – 15.0 Forward ← ← km/h 0 - 3.73 0 - 6.0 Speed mph [2WD km/h [2WD (HST) selection of selection of Reverse ← ← model: 0 - model : 0 - 5.59 mph] 9.0 km/h]...

  • Page 18: Names Of Each Section

    LM315GC Product Overview Carbon Dioxide (CO ) Emissions Regulation Decals Measurement Positions of Regulation Decals For CO emissions measurement on the engine of this machine, refer to the engine's owner's manual. Names of Each Section quwxcl-125 Positions of Regulation Decals_001...

  • Page 19: Description Of Regulation Decals

    LM315GC Product Overview Description of Regulation Decals Year of Manufacture Decal Serial Number Plate (For Europe) The year of manufacture decal indicates the The serial number plate indicates the model year when this machine was manufactured. and serial number of the machine.

  • Page 20: Safety Signs And Instruction Signs

    If they are damaged, become dirty, or peel off, replace them with new ones. Part numbers for decals that need to be replaced are listed in the parts catalog. Order them from a Baroness dealer or Kyoeisha. 2z2dxu-001 Positions of Safety Decals and Instruction...

  • Page 21: Description Of Safety Decals And Instruction Decals

    LM315GC Product Overview Caution to Mutilation Decal D operation decal Caution to mutilation decal K4205001600 Fire prohibited decal DECAL, CAUTION TO MUTILATION Hydraulic oil icon Warning Diesel fuel decal May cut your hand or leg - Stop the cutter Caution for high temperatures decal rotation and engine.
  • Page 22 LM315GC Product Overview Hydraulic Oil Icon Caution for High Temperatures Decal K4209000980 K4205001920 Hydraulic oil icon Decal, caution for high temperatures Read the Owner's Operating Manual. Caution High temperature - Do not touch. Otherwise, you will get burned. i77xz6-001 Hydraulic Oil Icon_001...
  • Page 23 LM315GC Product Overview Caution Slope Decal Caution for Slopes (3WD) Decal K4205002040 K4205002080 Decal, caution slope Decal, caution for slopes (3WD) (3WD spec model only) Caution Warning Rollover - Do not work on slopes of 15 degrees or more. Rollover - Do not switch between 2WD and When you descend a slope, drive at low 3WD while traveling on downward slopes.
  • Page 24 LM315GC Product Overview Decal on Reading Owner's Operating Manual K4205001560 Decal, read Owner's Operating Manual Warning Read the Owner's Operating Manual. tpfrw8-001 Decal on Reading Owner's Operating Manual_001 Page 3-10 Safety Signs and Instruction Signs...

  • Page 25: Handling Instructions

    LM315GC Handling Instructions Inspections ..........Page 4-3 Warning Mechanisms ......Page 4-26 Operation Method ........ Page 4-26 Reel Cutter (Cutting Cylinder) and Bed Knife (Bottom Blade) ...... Page 4-3 Cautions for when You Leave The Cover ............. Page 4-3 Machine ..........Page 4-26 Roller .............
  • Page 26 LM315GC Handling Instructions Before Long-Term Storage ....Page 4-42 Page 4-2...

  • Page 27: Inspections

    LM315GC Handling Instructions Cover Inspections Inspection of Covers Inspect the machine according to the maintenance schedule so that you will be able to Warning take advantage of its optimum performance for a long period of time. If you have removed the covers during...

  • Page 28: Dustproof Net

    LM315GC Handling Instructions Dustproof Net Cleaning of Radiator Inspection of Dust-Proof Mesh Important Make sure that there is no damage to the An unclean radiator cover may cause dust-proof mesh. overheating or damage to the engine. Make sure that the dust-proof mesh is not It may also cause malfunction of the hydraulic contaminated.

  • Page 29: Coolant

    LM315GC Handling Instructions Coolant Coolant Supply Inspection of Coolant Caution Do not touch the radiator or coolant during Caution engine operation or right after the engine has Do not touch the radiator or coolant during been turned off. engine operation or right after the engine has Otherwise, you may get burned due to high been turned off.

  • Page 30: Hydraulic Oil

    LM315GC Handling Instructions Hydraulic Oil Supply Reserve tank Reserve tank cap Important If no coolant is in the reserve tank, follow the steps below to fill the tank with clean Do not mix different types of oil. water. Open the radiator cap, and then supply Important clean water up to the opening.

  • Page 31: Air Cleaner

    LM315GC Handling Instructions Replace the air cleaner cap, and then fix it Air Cleaner securely with the clips. Inspection of Air Cleaner The air cleaner is a component that removes dirt from the intake air to prevent wear of the cylinder liners and piston rings so that the engine will always operate smoothly.

  • Page 32: Battery

    LM315GC Handling Instructions Battery Supply of Battery Fluid Inspection of Battery Danger Danger Be careful not to let your skin, eyes or clothes, Danger Danger etc., come into contact with the battery fluid or Keep fire away while inspecting or charging accidentally swallow the fluid.

  • Page 33: Tire

    LM315GC Handling Instructions Tire Wire Inspection of Tires Inspection of Wire Check the pneumatic pressure of the tires. Make sure that the wire is not cracked or damaged. Make sure that there are no cracks, damage or abnormal wear. If the wire is cracked or damaged, replace it (For green/For field) with a new one immediately.

  • Page 34: Fuel

    LM315GC Handling Instructions The appropriate oil level should be between Replace the oil filler cap. the upper and lower limit lines on the gauge. kx9ti-004 Supply of Engine Oil_001 rnr453-004 Oil filler cap Inspection of Engine Oil_002 It will take a while for the supplied engine oil Oil level gauge to descend into the oil pan.
  • Page 35 LM315GC Handling Instructions Fuel Supply Air Bleeding of Fuel System Warning Important Supply fuel before starting the engine. Be sure to tighten the air-bleeding plug except Never remove the tank cap or supply fuel when air bleeding. while the engine is running.

  • Page 36: Fuel Filter

    LM315GC Handling Instructions Make sure that the traveling pedal is Grass Catcher neutral. Inspection of Grass Catcher Set the ignition key to "START" position. Important The grass catcher may no longer correctly collect grass clippings due to its wear, In the case that there are still air bubbles in damage, deformation, etc., caused by...

  • Page 37: Tightening Torques

    LM315GC Handling Instructions Tightening Torques Important Refer to the Tightening Torque table. Note that the Baroness product warranty may not apply to defects caused by incorrect or overtorque tightening, etc. Standard Tightening Torques Bolts and Nuts Important A number of bolts are used in each part of this machine.
  • Page 38 LM315GC Handling Instructions General bolt Strength classification 4.8 Nominal diameter tib3yb-001 kgf-cm lb-in 3 - 5 30.59 - 50.99 26.55 - 44.26 7 - 9 71.38 - 91.77 61.96 - 79.66 14 - 19 142.76 - 193.74 123.91 - 168.17 29 - 38 295.71 - 387.49...

  • Page 39: Principal Tightening Torques

    LM315GC Handling Instructions Principal Tightening Torques Tightening Torque by Model LM315GC Tighten the following bolts and nuts at the torque specified in the table. For thread locking adhesive, apply a middle strength thread locker (ThreeBond 1322 or equivalent anaerobic sealant).
  • Page 40 LM315GC Handling Instructions Tightening torque Thread Location Code Part name locking kgf-cm lb-in adhesive Reel shaft LM315GB2102Z0 Reel gear fixing nut 25.49 22.13 Reel shaft (with LM315GB2101Z0 20-tooth reel gear 25.49 22.13 Groomer) Bed knife Screw, heat-treated 71.38 – 61.96...

  • Page 41: Adjustment Before Work

    LM315GC Handling Instructions Adjustment before Work Adjustment of Seat Use the seat adjustment levers to adjust the seat. Adjust the position according to the operator's body size. Use the forward/backward adjustment lever to adjust the seat back and forth. Use the backrest tilt adjustment lever to bs3d75-001 adjust the angle of the backrest.

  • Page 42: Adjustment Of Blade Engagement

    LM315GC Handling Instructions Adjustment of Blade Engagement Caution When handling the reel cutter (cutting cylinder) or bed knife (bottom blade), wear gloves to protect your hands. Pay attention not to let the reel cutter (cutting cylinder) catch your gloves. Otherwise, you may injure your hand or fingers.

  • Page 43: Adjustment Of Cutting Height

    Adjust the cutting height to fit your cutting work. would be larger with C since the offset distance is larger. Important LM315GC (for tee mowing) This applies the set cutting height that differs You can adjust the rear roller by eight from the actual cutting height.
  • Page 44 32.0 - 35.0 mm (1.260 - 1.378 in) 40.0 - 43.0 mm (1.575 - 1.693 in) Not recommended by manufacturer. Not recommended by manufacturer. LM315GC (for field mowing) You can adjust the rear roller by eight stages. Attach the rear roller in a position that suits your work requirements within the cutting height range.
  • Page 45 LM315GC Handling Instructions Adjustment of Front Roller Bed knife (bottom blade) Cutting height setting screw Set the slide caliper to the required cutting Cutting height gauge height, adjust the neck position of the Cutting height cutting height setting screw of the cutting...
  • Page 46 LM315GC Handling Instructions Front groomer Cutting height Groomer setting screw Cutting height gauge Cutting height gauge Cutting height setting screw Front roller Operating height Front roller Rear roller Loosen the nuts fixing the right and left Bed knife (bottom blade) groomer adjustment bolts.
  • Page 47 LM315GC Handling Instructions Cutting Height and Blade Thickness of Bed Knife (Bottom Blade) Important The recommended minimum cutting heights are based on those of common greens. They may vary according to the green conditions and machine specifications. If the green undulation is hard, set it a little bit higher in order not to damage the green surface.

  • Page 48: Procedure To Start/Stop Engine

    LM315GC Handling Instructions Adjustment of Cutter Adjustment Spring If the diameter of the reel cutter (cutting cylinder) becomes smaller, adjust the cutter adjustment spring. Adjust the blade engagement. Loosen the pipe with cutter adjusting screw, and then adjust the length of the spring coil to approximately 26.0 mm (1.024 in).
  • Page 49 LM315GC Handling Instructions Important Important The thermo-start lamp turns off at the Quickly returning the ignition key from the specified time. However, the lamp turning off "START" position to the "ON" position may is not related to the glow plug generating heat.

  • Page 50: Operation Method

    LM315GC Handling Instructions Safety Mechanisms Caution Never park the machine on a slope. This machine features a safety device for starting/stopping the engine. Positions of Operation Decals As for starting the engine, the safety device prevents the engine from starting unless it meets each of the following four conditions.

  • Page 51: Description Of Operation Decals

    LM315GC Handling Instructions Reel rotation/stop mark Low speed Engine rotation mark High speed Mower unit Up/Down decal Mower Unit Up/Down Decal Key switch mark K4203001520 Mower unit up-switch (with reel excess Decal, lifting units discharge system) mark This indicates up-down of the mower unit.
  • Page 52 LM315GC Handling Instructions Mower Unit Up-Switch (with Reel Excess Light Switch Mark Discharge System) Mark Note: Mower unit up-switch (with reel excess Depending on the specifications, this function discharge system) mark may not be available. This indicates mower unit up-switch and reel K4203001610 excess discharge system.

  • Page 53: Light Switch

    LM315GC Handling Instructions BACKWARD Decal Mower Unit Reel Rotation Changeover Decal K4203001440 K4203001550 Decal, BACKWARD Sticker, rotating direction This indicates backward travel. This indicates changeover of normal rotation, neutral and reverse rotation of mower unit reel cutter. BACKWARD kqca3e-002 BACKWARD Decal_001...

  • Page 54: Throttle Lever

    LM315GC Handling Instructions Throttle Lever Mower Pedal The throttle lever is located in the operation Caution panel and enables you to adjust the engine rpm. Do not keep depressing the mower pedal after Move the throttle lever toward the "High speed"...

  • Page 55: Joystick

    LM315GC Handling Instructions Joystick Mower Unit Up Switch Note: Up Switch (with Reel Excess Discharge System) Depending on the specifications, this function may not be available. Warning Important The reel cutter rotates while holding down the up switch when the reel rotation switch is set Even if the reel rotation switch is set to the to the "Rotation"...

  • Page 56: 2Wd/3Wd Selector Switch

    LM315GC Handling Instructions Reel excess discharge system Note: ･ Reel excess discharge system is the Depending on the specifications, this function function to remove clippings inside the reel may not be available. cutter by rotating the reel cutter with the up...

  • Page 57: Reel Rotation Switch

    LM315GC Handling Instructions When the reel rotation switch is set to the Reel Rotation Switch "Rotation" position, the reel cutters (cutting cylinders) will rotate or stop in sync with the up Warning and down motion of the mower units. When the...

  • Page 58: Transmission Selector Lever

    Traveling Pedal Important Caution For the LM315GC (for fields), normally cut When the machine is traveling at a high with the lever set to the "Low speed" position. speed, it will not stop immediately after you take your foot off the traveling pedal.

  • Page 59: Parking Brake Lever

    LM315GC Handling Instructions Hood Caution Do not open the hood in strong winds. Caution Be careful not to pinch your fingers when you open or close the hood. yo3h9x-006 Remove the bolt. Traveling Pedal_001 Lift up the hood. Forward pedal...

  • Page 60: Underseat Cover

    LM315GC Handling Instructions Rotate the lock lever 90 degrees clockwise Underseat Cover to fix the underseat cover. Caution Be careful not to pinch your fingers when you open or close the underseat cover. Front Remove the grass catcher located at the center.

  • Page 61: Instruments

    LM315GC Handling Instructions Swisher Holder Hour Meter Note: The hour meter is located in the operation Depending on the specifications, this function panel, and indicates the accumulated operation may not be available. time of the engine. Swisher pole can be stored in this holder for The number in black figures on a white transport.

  • Page 62: Water Temperature Gauge

    LM315GC Handling Instructions Water Temperature Gauge The water temperature gauge is located in the operation panel. This instrument indicates the water temperature inside the engine. If the water temperature gauge indicates a level close to "H" during operation, the machine is overheated.

  • Page 63: Travel Of Machine

    LM315GC Handling Instructions Travel of Machine Oil Pressure Lamp The oil pressure lamp is the right pilot lamp Moving The Machine located in the operation panel. It turns on when the ignition key is set to the Warning "ON" position before the engine starts. It turns Set the reel rotation switch to the "Stop"...

  • Page 64: Cutting Work

    LM315GC Handling Instructions Tow the machine slowly. Towing The Machine Cutting Work If the machine does not travel due to engine trouble, etc., you can move it in the following Cutting Work ways: ･ Pushing by hand Warning Towing (See the following instruction.) ･...

  • Page 65: Reel Excess Discharge System

    LM315GC Handling Instructions Start the work following the procedure below. Preventing lumps of clippings from falling ･ onto the green. Depress the traveling pedal. Use reel excess discharge system so that Depress the mower pedal when the the clippings inside the reel cutter can be...

  • Page 66: Transporting

    LM315GC Handling Instructions Removing Grass Catcher To discard the collected grasses, set the reel rotation switch to the "Stop" position. Lower the mower unit. Apply the parking brake. Stop the engine. Lift up the grass catcher and remove it. lovz39-001...

  • Page 67: Maintenance

    LM315GC Maintenance Maintenance Precautions ..... Page 5-2 Maintenance Schedule ......Page 5-2 Adjusted Value ........Page 5-8 Jacking Up The Machine .......Page 5-9 About Jacking Up The Machine .....Page 5-9 Jack-Up Points ........Page 5-9 Greasing ..........Page 5-10 About Greasing ........Page 5-10 Greasing Points ........

  • Page 68: Maintenance Precautions

    Use tools appropriate for each maintenance operation. Important For the safe and best performance of your machine, use Baroness genuine parts for replacement and accessories. Please note that our product warranty may be void if you use non-genuine parts for replacement or accessories.
  • Page 69 LM315GC Maintenance Maintenance Item 50 hours first Adjust fan belt change, every 　 　 　 　 ○ ○ 　 　 　 　 　 　 　 　 　 　 　 　 tension 100 hours thereafter 50 hours first change, every Clean fuel filter 　...
  • Page 70 LM315GC Maintenance Maintenance Item Check valve 　 　 　 　 　 　 　 　 　 ○ 　 　 　 　 　 　 　 　 　 clearance Check injection *4.*5 　 　 　 　 　 　 　 　 　 　 ○ 　 　 　 　 　 　 　...
  • Page 71 LM315GC Maintenance Maintenance Item Check steering By starting the wheel motion 　 ○ 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 engine (Lock to lock) Clean machine 　 　 ○ 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　...
  • Page 72 LM315GC Maintenance Maintenance Item Check mounting whichever 　 　 　 　 　 ○ 　 　 　 　 　 　 ○ 　 　 　 　 　 bracket of battery comes earlier Check every Check looseness 100 hours or and corrosion of every month 　...
  • Page 73 LM315GC Maintenance Maintenance Item Check groomer 　 ○ 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 condition Engage blades 　 ○ 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　...

  • Page 74: Adjusted Value

    ･ *3: Failed maintenance may largely cause damage to the flexible wires. *4: Consult your local Baroness Dealer or local KUBOTA Dealer for this service. ･ The items above (*5 marked) are registered as emission related critical parts by KUBOTA in the ･...

  • Page 75: Jacking Up The Machine

    LM315GC Maintenance Jacking Up The Machine Front right frame Front left frame About Jacking Up The Machine Engine mount frame Front right frame Warning When replacing a tire or beginning any other maintenance or repairs, be sure to chock the wheels to prevent the machine from moving.

  • Page 76: Greasing

    LM315GC Maintenance Greasing No. of Greasing Location greasing 　 schedule About Greasing points Mower unit 　 Since there may be adhesion or damage due Mower arm fulcrum 　 B 　 to lack of grease on moving parts, they must be greased.
  • Page 77 LM315GC Maintenance Right side Groomer Note: Depending on the specifications, this function may not be available. Left side 8bq62b-389 Greasing Points_004 Rear roller Note: Depending on the specifications, this 8bq62b-392 function may not be available. Greasing Points_007 Left side Right side...
  • Page 78 LM315GC Maintenance Mower arm fulcrum Belt tension lever Important Important Without greasing the mower arm fulcrum, the Without greasing the tension lever, it can worn shaft can cause backlash in the lift arm adhere. and mower arm. The backlash may influence up-down range of the mower unit and cutting finish.
  • Page 79 LM315GC Maintenance Mower pedal shaft fulcrum Flexible wire edge There is one greasing point on each flexible wire. Grease by one stroke (1.0mL) every 50 hours. 8bq62b-399 Greasing Points_014 Flexible wire bracket 8bq62b-403 Greasing Points_018 Important Lack of grease in the flexible wire may cause damage to it.

  • Page 80: Maintenance Work

    Have the following items ready: Strips of newspaper, Abrasive [Back lapping powder Maintenance Work mixed with oil; or gel compound (Baroness Back Lapping of Reel Cutter (Cutting genuine abrasive)], Brush. Cylinder) Back lapping is work similar to sharpening a cooking knife.
  • Page 81 LM315GC Maintenance Stop the engine. Caution Wash off or wipe off with a cloth, etc., the When handling the reel cutter (cutting abrasive from the reel cutter (cutting cylinder) or bed knife (bottom blade), wear cylinder), and then check it for sharpness.

  • Page 82: Adjusting Cam

    LM315GC Maintenance Adjusting CAM Reel cutter (Cutting cylinder) Bed knife (Bottom blade) When the gap at the left frame side between Lock nut the reel cutter (cutting cylinder) and the bed Cam bush knife (bottom blade) appears. Max 0.3 mm (0.012 inch)

  • Page 83: Removing/Installing Tires

    LM315GC Maintenance Rear Tire Bearing Seal Follow the steps below to remove the rear Reel cutter (Cutting cylinder) tires: Inner nut [2WD] Outer nut Securely place the jack beneath the jack-up points of the engine mount frame area, and then raise it until the tire lifts off the ground.

  • Page 84: Adjustment Of Belt Tension

    LM315GC Maintenance Important Important Tighten the bolts in the tightening order Tighten the bolts in the tightening order (crosswise). (crosswise). For installing the rear tires, reverse the For installing the rear tires, reverse the removing procedure. removing procedure. [3WD] Adjustment of Belt Tension...
  • Page 85 LM315GC Maintenance Reel Cutter Drive Belt Tilt the underseat cover forward and open the cover. Open the hood. Press the middle of the belt with your finger to check the belt tension. If the belt tension is inappropriate, loosen the bolts and move the flexible wire housing...

  • Page 86: Adjustment Of Parking Brake

    LM315GC Maintenance Adjustment of Parking Brake Caution If the brake wire is cut, the machine will be unable to stop. If the brake wire is cracked or damaged, replace it with a new one immediately. Important cs6lrm-002 Make sure that the brake is effective on...

  • Page 87: Change Of Coolant

    LM315GC Maintenance Important Tightly close the radiator cap. If the cap is loose or incorrectly installed, water may leak and the engine may overheat. When mixing antifreeze and clean water (soft water), refer to "Relationship between concentration of long-life coolant (LLC) and freezing temperature"...

  • Page 88: Change Of Hydraulic Oil

    LM315GC Maintenance Remove the radiator cap and drain the Stop the engine, and then allow the radiator coolant. to cool. Check if the coolant level in the reserve tank is between "FULL" and "LOW", and then supply coolant if necessary.

  • Page 89: Change Of Hydraulic Oil Filter

    LM315GC Maintenance Hydraulic tank Important Drain plug When replacing the hydraulic oil filter, be sure to drain the oil into a container and discard it Open the hood. in accordance with local laws and regulations. Follow the steps below to fill with new coolant.

  • Page 90: Change Of Air Cleaner

    LM315GC Maintenance Check underneath the machine for oil Follow the steps below to remove the old leakage. engine oil. Start and run the engine to warm up the Change of Air Cleaner engine oil. A contaminated air cleaner element may cause With the machine on a level surface, stop malfunction of the engine.

  • Page 91: Replacement Of Engine Oil Filter

    LM315GC Maintenance Make sure that there is no oil leakage at the Replacement of Engine Oil Filter sealing surface of the filter cartridge. Check the engine oil level. Caution If it is low, supply engine oil until it reaches Be careful with hot oil, which could cause the specified level.

  • Page 92: Grease Change Of Transmission

    LM315GC Maintenance Remove the ring nut, and then remove the Fuel cock cup. Fuel filter Air-bleeding plug ON (open) OFF (close) Remove air out of the fuel. Grease Change of Transmission The transmission is located behind the driver's seat. Change grease every two years.

  • Page 93: Change Of Fuse

    LM315GC Maintenance Change of Fuse Glow lamp timer Key stop timer Fuse Box Glow lamp timer, glow lamp (thermo-start lamp) Important Before performing maintenance on the 15 A Engine stop solenoid electrical system, be sure to disconnect the 15 A Others negative terminal of the battery.

  • Page 94: Check The Operation Status Of The Relay

    LM315GC Maintenance Check The Operation Status of The Relay Interlock Relay Mower Unit Control Relay The relay box is located under the underseat cover. The relay box is located behind the seat. This controls a safety device for starting/ This controls Up/Down of the mower unit and stopping the engine.

  • Page 95: Removal Of Mower Unit

    LM315GC Maintenance Removal of Mower Unit Remove the clip which fixes the mower unit and flexible wire. l9sh2i-002 Removal of Mower Unit_001 Clip Slide the stopper of the mower attaching pipe forward and pull it out. Pull out the mower unit and remove it.
  • Page 96 LM315GC Maintenance Page 5-30 Maintenance Work...
  • Page 100 1-26, Miyuki-cho, Toyokawa-city, Tel : +81 - 533 - 84 - 1390 Head Office Fax : +81 - 533 - 84 - 1220 Aichi-pref, 442-8530 JAPAN LM315GC-UMA-GBZ/19L-00-S.K E02[LM315_EU02]...

Table of Contents