Related Manuals for Baroness LM3210A
Summary of Contents for Baroness LM3210A
- Page 1 5-Unit Reel Mower Owner's Operating Manual Serial No. LM3210A：11020- "Required reading" Read this manual before using the machine. Original Instructions Ver.1.2...
- Page 2 LM3210A Regulations California Proposition 65 EU Emission Control (StageⅤ) (For California, USA) (For Europe) Important WARNING: No deliberate tampering with or misuse of the Operating, servicing and maintaining engine emissions control system should take a passenger vehicle or off-road place.
- Page 3 LM3210A Greeting Thank you for purchasing the Baroness product. This manual describes the proper handling, adjustment, and inspection of your product. We hope you will use the product safely, and take advantage of its best performance. Keeping The Owner's Operating...
- Page 4 The operator is responsible for operating the product properly and safely. Maintenance should only be performed by a certified specialist. If you have any questions concerning maintenance or genuine parts, please contact a Baroness dealer or Kyoeisha. When making inquiries about the product, please specify the product's model designation and serial number.
- Page 5 When replacing parts, be sure to use genuine Baroness parts or parts designated by Kyoeisha. Note that the Baroness product warranty may not apply to defects caused by the use of parts from other companies. Prior to use, carefully read the following manuals to thoroughly understand the contents for safe and correct operation.
- Page 6 LM3210A Introduction...
-
Page 7: Table Of Contents
LM3210A Contents Safety .............. Page 1-1 Safe Operating Practices .......Page 1-2 Disposal ............Page 2-1 Recycle and Waste Disposal ......Page 2-2 Product Overview .......... Page 3-1 Specifications ..........Page 3-2 Names of Each Section ......... Page 3-4 Regulation Decals ..........Page 3-5 Safety Signs and Instruction Signs .... - Page 8 LM3210A Contents...
-
Page 9: Safety
LM3210A Safety Safe Operating Practices ...... Page 1-2 Training ..........Page 1-2 Preparation ..........Page 1-2 Operation ..........Page 1-3 Maintenance and Storage ..... Page 1-4 Page 1-1... -
Page 10: Safe Operating Practices
LM3210A Safety Failure to adequately follow these safety Never allow children or people unfamiliar precautions may cause an accident resulting in with these instructions to use or service the injury or death. machine. Local regulations may restrict the age of the... - Page 11 LM3210A Safety Exercise care in the handling of fuel. Remember there is no such thing as a safe slope. Travel on grass slopes requires Warning particular care. To guard against overturning: Warning-Fuel is highly flammable. Take the following precautions. Do not stop or start suddenly when going up or downhill.
- Page 12 LM3210A Safety After striking a foreign object or if an Do not operate the machine when there is abnormal vibration occurs. the risk of lightning. Inspect the machine for damage and Maintenance and Storage make repairs before restarting and operating the equipment.
- Page 13 LM3210A Safety When checking the hydraulic circuit for pinhole leaks or oil leakage from nozzles, do not use your hands. Use items such as paper or corrugated cardboard to find leakage points. Be extremely careful with high-pressure oil as it may pierce your skin, resulting in an injury.
- Page 14 LM3210A Safety Page 1-6 Safe Operating Practices...
-
Page 15: Disposal
LM3210A Disposal Recycle and Waste Disposal ....Page 2-2 About Recycle ........Page 2-2 About Waste Disposal ......Page 2-2 Page 2-1... -
Page 16: Recycle And Waste Disposal
LM3210A Disposal Recycle and Waste Disposal About Recycle Recycling battery etc. is recommended for environmental conservation and economical use of resources. It may be required by local laws. About Waste Disposal Make sure that waste generated when servicing or repairing the machine is disposed of in accordance with local regulations. -
Page 17: Product Overview
LM3210A Product Overview Specifications ........Page 3-2 Specifications .........Page 3-2 Sound Pressure Level ......Page 3-3 Sound Power Level ....... Page 3-3 Vibration Level ........Page 3-3 Carbon Dioxide (CO2) Emissions Measurement .........Page 3-3 Names of Each Section ......Page 3-4 Regulation Decals ........Page 3-5... -
Page 18: Specifications
LM3210A Product Overview Specifications Specifications Model LM3210A (Type_F) LM3210A (Type_R) Total length 124.06 in 315 cm 129.92 in 330 cm During operation 144.49 in 367 cm 144.88 in 368 cm Total width Dimension During transport 92.52 in 235 cm 92.91 in... -
Page 19: Sound Pressure Level
LM3210A Product Overview Sound Pressure Level Sound Pressure Level This machine was confirmed to have a continuous A-weighted sound pressure level of 88 dB by measuring identical machines in accordance with the procedure specified in ISO5395-1:2013. Sound Power Level Sound Power Level... -
Page 20: Names Of Each Section
LM3210A Product Overview Names of Each Section Seat Steering handle Tilt lever Diff-lock switch Parking brake lever Brake pedal Forward pedal Reverse pedal Mower unit up/down lever Throttle knob Reel rotation switch 2WD/4WD selector switch Reel rotation/stop switching lever Fuel tank... -
Page 21: Regulation Decals
LM3210A Product Overview Regulation Decals Specification Decal (For Europe) Positions of Regulation Decals CE mark indicates that the machine sold in the EU nations complies with the EU requirements. The Specification decal indicates the CE marking, model , and weight, etc. - Page 22 LM3210A Product Overview Year of Manufacture Decal Battery Capacity Decal (For Europe) (For Europe) The year of manufacture decal indicates the The battery capacity decal indicates the year when this machine was manufactured. capacity by 20HR and CCA. YEAR OF...
- Page 23 LM3210A Product Overview Battery Danger Decal California Proposition 65 Decal (Riding Type) (For USA) (For the State of California, USA) Battery Danger Decal describes handling California Proposition 65 decal describes the precautions for battery. warning messages as required by California Proposition 65.
-
Page 24: Safety Signs And Instruction Signs
6iul4h-040 Positions of Safety Signs and Instruction Signs_002 Part numbers for decals that need to be replaced are listed in the parts catalog. Order them from a Baroness dealer or Kyoeisha. Positions of Safety Signs and Instruction Signs 6iul4h-054... - Page 25 LM3210A Product Overview Operation decal Start/stop decal (reel) Caution to mutilation decal Caution for high temperatures decal Caution to injury decal Caution to rotating object decal Hydraulic oil icon Diesel fuel icon Fire prohibited decal 6iul4h-057 Caution for mower lock decal...
-
Page 26: Description Of Safety Decals And Instruction Decals
Turn the key to the "ON (GLOW)" Warning position, and then wait for the "BARONESS" logo to turn off. Apply the parking brake, stop the engine, Turn the key to the "START" position. remove the ignition key, and then leave the machine. - Page 27 LM3210A Product Overview Caution to Mutilation Decal Caution to Injury Decal K4205001600 K4205001580 DECAL, CAUTION TO MUTILATION Decal, caution to injure Warning Caution May cut your hand or leg - Stop the cutter May pinch - There is a risk of being pinched.
- Page 28 LM3210A Product Overview Hydraulic Oil Icon Fire Prohibited Decal K4209000980 K4205001940 Hydraulic oil icon Decal, fire prohibited Read the Owner's Operating Manual. Warning Keep away from fire. i77xz6-001 Hydraulic Oil Icon_001 Diesel Fuel Icon r653fo-001 K4209001000 Fire Prohibited Decal_001 Diesel fuel icon Caution for Mower Lock Decal Use diesel fuel.
- Page 29 LM3210A Product Overview Caution for Spouting Coolant Decal Caution Exhaust Gas Decal K4205001970 K4205001950 Decal, caution for spouting coolant Decal, caution exhaust gas Caution Warning Caution for spouting coolant - Do not open Caution for exhaust gas while hot. High temperature - Do not touch. Otherwise, you will get burned.
- Page 30 LM3210A Product Overview Caution to Noise Decal K4205002090 Decal, caution to noise bwu9po-001 Caution to Noise Decal_001 Maintenance Decal K4209001550 Label, maintenance The maintenance decal indicates the necessary inspection and maintenance items for this machine. 3wt6ls-003 Maintenance Decal_001 Page 3-14...
-
Page 31: Handling Instructions
LM3210A Handling Instructions Inspections ..........Page 4-3 Start/Stop of Engine ......Page 4-24 Safety Mechanisms ......Page 4-25 Reel Cutter (Cutting Cylinder) and Warning Mechanisms ......Page 4-26 Bed Knife (Bottom Blade) ...... Page 4-3 Cover ............. Page 4-3 Operation Method ........ Page 4-26 Roller ............. - Page 32 LM3210A Handling Instructions Transporting Procedure ....... Page 4-77 Storage ..........Page 4-77 Before Long-Term Storage ....Page 4-77 Page 4-2...
-
Page 33: Inspections
LM3210A Handling Instructions Cover Inspections Inspection of Covers Inspect the machine according to the maintenance schedule so that you will be able to Warning take advantage of its optimum performance for a long period of time. If you have removed the covers during... -
Page 34: Cr Brush
LM3210A Handling Instructions CR brush Cleaning of Radiator Cover Inspection of CR Brush Important Note: An unclean radiator cover may cause Depending on the specifications, this function overheating or damage to the engine. may not be available. It may also cause malfunction of the hydraulic Bearing wear due to frequent use or bearing system. -
Page 35: Radiator
LM3210A Handling Instructions Radiator Coolant Inspection of Radiator Inspection of Coolant Make sure that there is no damage to the Caution radiator. Do not touch the radiator or coolant during Make sure that the radiator is not engine operation or immediately after the contaminated. -
Page 36: Oil Cooler
LM3210A Handling Instructions If no coolant is in the reserve tank, follow Coolant Supply the steps below to fill the tank with clean water. Caution Open the radiator cap, and then supply Do not touch the radiator or coolant during clean water up to the opening. -
Page 37: Hydraulic Oil
LM3210A Handling Instructions Unlock the rubber catches on the left and Hydraulic Oil Supply right of the oil cooler, and then tilt the oil cooler. Important Do not mix different types of oil. Important Use Shell Tellus S2M46 (or equivalent) as hydraulic oil. -
Page 38: Air Cleaner
LM3210A Handling Instructions Attach the outer element to the air Air Cleaner cleaner body. Inspection of Air Cleaner Replace the air cleaner cap, and then fix it securely using the clips. Liners and piston rings so that the engine will always operate smoothly. -
Page 39: Battery
LM3210A Handling Instructions Battery Supply of Battery Fluid Inspection of Battery Danger Danger Be careful not to let your skin, eyes or clothes, Danger Danger etc., come into contact with the battery fluid or Keep away from fire while inspecting or accidentally swallow the fluid. -
Page 40: Tire
LM3210A Handling Instructions Tire Belt Inspection of Tires Inspection of Belt Check the pneumatic pressure of the tires. Warning Make sure that there are no cracks, The engine must be stopped when the belt is damage or abnormal wear. inspected. -
Page 41: Engine Oil
LM3210A Handling Instructions Engine Oil Supply of Engine Oil Inspection of Engine Oil Important Do not supply too much engine oil. Otherwise, Important the engine may be damaged. Securely tighten the oil level gauge and oil filler cap. Important Stop the engine, wait for 10 to 20 minutes Do not mix different types of engine oil. -
Page 42: Fuel
LM3210A Handling Instructions Note: Fuel The factory default low fuel level is 10%.The level can be changed optionally. Inspection of Fuel Quantity With the machine on a level surface, observe the fuel level in the monitor to check the fuel level. -
Page 43: Water Separator
LM3210A Handling Instructions Water Separator Inspection of Water Separator Important If water contaminates the fuel, the supply pump and injector will seize due to heat. The water separator removes water from the fuel. v1spa6-001 Make sure that debris and water have not Draining of Water Separator_001 accumulated in the cup. -
Page 44: Fuel Filter
LM3210A Handling Instructions v1spa6-001 Cleaning of Water Separator_001 Float Water drain plug Element Air-bleeding bolt Install the cup, element and float in their original positions. Bleed air from the fuel system. Fuel Filter Inspection of Fuel Filter The fuel filter works to remove foreign objects mixed into the fuel. -
Page 45: Tightening Torques
LM3210A Handling Instructions Tightening Torques Important Refer to the Tightening Torque table. Note that the Baroness product warranty may not apply to defects caused by incorrect or overtorque tightening, etc. Standard Tightening Torques Bolts and Nuts Important A number of bolts are used in each part of this machine. - Page 46 LM3210A Handling Instructions General bolt Strength classification 4.8 Nominal diameter tib3yb-001 kgf-cm lb-in 3 - 5 30.59 - 50.99 26.55 - 44.26 7 - 9 71.38 - 91.77 61.96 - 79.66 14 - 19 142.76 - 193.74 123.91 - 168.17 29 - 38 295.71 - 387.49...
-
Page 47: Principal Tightening Torques
LM3210A Handling Instructions Principal Tightening Torques Tightening Torque by Model LM3210A Tighten the following bolts and nuts at the torque specified in the table. For thread locking adhesive, apply a middle strength thread locker (ThreeBond 1322 or equivalent anaerobic sealant). - Page 48 LM3210A Handling Instructions Tightening torque Thread locking Location Code Part name adhesive kgf-cm lb-in Slotted nut of tie rod end K1610000020 458.87 398.30 － Tie rod Slotted nut of tie rod end K1611000020 458.87 398.30 － 67 - 683.20 - 593.02 -...
-
Page 49: Adjustment Before Work
LM3210A Handling Instructions Turn the suspension adjustment handle to Adjustment before Work adjust the firmness of the seat suspension. Refer to the suspension indicator while Adjustment of Steering Wheel making adjustments. [45 to 130 kg (99.2 to 286.6 lb)] Warning... -
Page 50: Adjustment Of Blade Engagement
LM3210A Handling Instructions If the reel cutter (cutting cylinder) is too ･ Adjustment of Blade Engagement tight to turn: Tighten the cutter adjustment nut to Caution reduce the contact pressure between the reel cutter (cutting cylinder) and the bed When handling the reel cutter (cutting knife (bottom blade). - Page 51 LM3210A Handling Instructions Attach the front roller in a position within the Front Wheel Type range of cutting height that suits your work requirements. Adjust the cutting height to fit your cutting work. To increase cutting height: You can adjust the wheel to one of four levels.
-
Page 52: Adjustment Of Cutter Adjustment Spring
LM3210A Handling Instructions Adjustment of Reel Cover Note: Depending on the specifications, this function may not be available. The angle of the reel cover can be adjusted. Pull the right and left knobs securing the reel cover to release it. -
Page 53: Adjustment Of Cr Brush
LM3210A Handling Instructions The scraper prevents grass clippings, etc., Adjustment of CR Brush from attaching to the rear roller. Note: Loosen the left and right lock nuts and nuts Depending on the specifications, this function of the scraper. may not be available. -
Page 54: Procedure To Start/Stop Engine
Make sure that the glow plug is generating If the engine does not start, stop using the heat, the "BARONESS" logo or "Warming battery for 30 to 60 seconds to avoid up" message appears in the monitor exhausting the battery. -
Page 55: Safety Mechanisms
As for starting the engine, the safety device prevents the engine from starting unless it After the "BARONESS" logo and the yellow meets each of the following four conditions. and red LEDs go off and the parameters An operator is sitting on the seat. -
Page 56: Operation Method
LM3210A Handling Instructions Warning Mechanisms Important When the buzzer (intermittent tone) sounds, be sure to stop operation since the engine is overheated. Do not stop the engine without idling. Allow the engine to cool down, first. Keep the engine idling for about 5 minutes before stopping. -
Page 57: Description Of Operation Decals
LM3210A Handling Instructions Reel Rotation Mark Key switch decal Reel rotation mark Reel rotation mark 2WD/4WD selector mark It illustrates Rotation/Stop of the reel cutter DPF regeneration mark (EN) (cutting cylinder). Mower unit up/down decal Light switch mark Engine rotation mark... - Page 58 LM3210A Handling Instructions DPF Regeneration Mark (EN) Light Switch Mark Note: DPF regeneration mark (EN) Depending on the specifications, this function This indicates the changeover of DPF may not be available. regeneration. Light switch mark It illustrates ON/OFF of the light.
- Page 59 LM3210A Handling Instructions Differential Lock Decal Parking Brake Decal K4203001420 K4203001340 Decal, differential lock Parking brake decal This indicates the positions for engaging or This shows how to lock and release the releasing the differential lock. parking brake. 3ujqne-001 kgtxi7-002...
- Page 60 LM3210A Handling Instructions BACKWARD Decal Lapping Decal K4203001440 K4203001590 Decal, BACKWARD Decal, lapping This indicates backward travel. This indicates rotational direction of the reel cutter (cutting cylinder). BACKWARD kqca3e-002 v57o51-001 BACKWARD Decal_001 Lapping Decal_001 BRAKE Decal Normal rotation (cutting rotation)
-
Page 61: Proximity Sensors
LM3210A Handling Instructions Relays Reel Stop Decal K4203001310 The relay box is located inside the right tank Decal, reel stop cover. This indicates stop of the reel cutter (cutting These relays control operation of the diff-lock, cylinder). rotation of the reel cutters (cutting cylinders), and 2WD/4WD selection. -
Page 62: Reel Rotation Switch
LM3210A Handling Instructions Reel Rotation Switch 2WD/4WD Selector Switch Caution Caution Set the reel rotation switch to the "Rotation" When working on a slope, be sure to use the position immediately before starting cutting machine in 4WD. work. At all other times, be sure to leave the reel rotation switch set to the "Stop"... -
Page 63: Dpf Auto Regeneration Inhibit Switch
LM3210A Handling Instructions DPF Auto Regeneration Inhibit Switch Caution Normally, set the DPF auto regeneration inhibit switch to "Auto regeneration mode". However, when operating in a location where fires may occur, set the DPF auto regeneration inhibit switch to "Auto regeneration inhibit mode". -
Page 64: Dpf Parked Regeneration Switch
LM3210A Handling Instructions DPF Parked Regeneration Switch Light Switch Note: Danger Danger Depending on the specifications, this function may not be available. Do not perform DPF regeneration in a location where fires may occur since it will become Caution extremely hot around the exhaust outlet during DPF regeneration. -
Page 65: Reel Reverse Switch
LM3210A Handling Instructions Reel Reverse Switch Reel Rotation/Stop Switching Lever Important Caution Do not switch the rotation directions, "Normal Before operating the reel rotation/stop rotation" or "Reverse" while the reel cutter switching lever, be sure to set the reel rotation (cutting cylinder) is rotating. -
Page 66: Reel Rotation Adjustment Valve
LM3210A Handling Instructions Reel Rotation Adjustment Valve Mower Lock Lever (Latch) These valves adjust the rotation speeds of the The mower lock levers (latches) are located in reel cutters (cutting cylinders). the foot area on the left and right sides. -
Page 67: Throttle Knob
LM3210A Handling Instructions Diff-Lock Switch Note: Depending on the specifications, this function may not be available. Important Do not operate the diff-lock switch unless it is necessary. The diff-lock switch is located below the right lwkjk9-002 side of the steering wheel and engages the... -
Page 68: Traveling Pedal
LM3210A Handling Instructions Traveling Pedal Brake pedal Parking brake lever Caution Parking Brake Lever When the machine is traveling at a high speed, it will not stop immediately after you Caution take your foot off the traveling pedal. Never park the machine on a slope. -
Page 69: Hood
LM3210A Handling Instructions Hood Underseat Cover Caution Caution Do not open the hood in strong winds. Be careful not to pinch your fingers when you open or close the underseat cover. Caution Make sure that the steering wheel is raised completely. -
Page 70: Instruments
LM3210A Handling Instructions Displayed Icon Instruments The icon appears at the top of the monitor Description of Monitor display. The monitor displays various information about the machine, such as the operating status and fault conditions. The information of desired items can be confirmed according to operating the keys. -
Page 71: Main Menu Items
LM3210A Handling Instructions 4-up display Main Menu Items Four parameters are displayed in the monitor display. While any parameter is displayed, press the With the 4-up display, a total of 8 menu key to display the main menu with the parameters are displayed over 2 pages. - Page 72 LM3210A Handling Instructions Parameter Items ￭ The parameters and corresponding information that appear in the monitor display are listed below. Monitor display L Monitor display S Description ENGINE SPEED ENG RPM Displays the engine rpm. DRIVERS DEMAND DEMAND TQ Displays the torque required by the ECU.
- Page 73 LM3210A Handling Instructions Monitor display L Monitor display S Description EXHAUST FILTER Displays the DPF outlet gas temperature measured by the EF OUT T OUTLET TEMP exhaust temperature sensor. Shows the status of the regeneration icon. PARTICUATE TRAP PT LAMP Icon not displayed="OFF", Icon blinking="ON BLINK", Icon...
- Page 74 LM3210A Handling Instructions Text 2 ･ Language With "LANGUAGES", the language used in the monitor display can be set to either of the following two. 1 of 4 C : 3 SPN 172 FMI 3 ･ ENGLISH CORRECTIVE ACTION: S e e S e r v i c e M a n u a l JAPANESE ･...
- Page 75 LM3210A Handling Instructions List of Fault Codes ￭ Important When the fault code appears in the monitor display, refer to "Kubota DIAGNOSIS MANUAL COMMON RAIL SYSTEM" or contact your dealer. The fault codes (DTC) and corresponding information that appear in the monitor display are listed below.
- Page 76 LM3210A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Insufficient output Stop ENG Fuel leak (in - Worsening consumption is To minimize PM Key switch turn...
- Page 77 LM3210A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Insufficient output - Worsening exhaust gas Open circuit or +B Stop ENG emissions short circuit of...
- Page 78 LM3210A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Engine speed See Service Diagnostic Engine overrun P0219 exceeds - Overrun Manual counter = zero...
- Page 79 LM3210A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 (At low temperature) Ground short of Ground short of See Service Key switch turn glow relay...
- Page 80 LM3210A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Insufficient output Injector charge Stop ENG voltage: Low Injector charge - Worsening Key switch turn...
- Page 81 LM3210A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Faulty starting - Insufficient output Sensor supply Sensor supply See Service Key switch turn - Worsening...
- Page 82 LM3210A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Accelerator position sensor Diagnostic Accelerator signal error counter = zero See Service - Insufficient Position Sensor...
- Page 83 LM3210A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Insufficient output CAN2 +B or GND See Service Key switch turn CAN2 Bus off U0075...
- Page 84 LM3210A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Exhaust gas Open circuit or +B See Service Key switch turn temperature P0544 3242 short circuit of None ...
- Page 85 LM3210A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Differential Ground short See Service Key switch turn pressure P2454 3251 circuit of sensor None ...
- Page 86 LM3210A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Stop engine!! PM accumulation To minimize PM - Insufficient Diagnostic Excessive PM4 Contact dealer P3007 3701...
- Page 87 LM3210A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Worsening exhaust gas Over heat pre- See Service Diagnostic P3025 523603 15 Coolant temp. ...
- Page 88 LM3210A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Loss of DPF See Service Loss of functon of P3015 3936 Function Manual Open Circuit of...
- Page 89 LM3210A Handling Instructions "RESTORED TO DEFAULTS" appears in Engine Configuration the monitor display, and the parameters are reset to the factory defaults of the This function is not supported. following 8 items. 1-Up Display Setup ENGINE SPEED With "SETUP 1-UP DISPLAY", the displayed...
- Page 90 LM3210A Handling Instructions Highlight "CUSTOM SETUP", and then To deselect a parameter and remove it press the Enter key. from the list of displayed parameters The list of parameters appears. Highlight the parameter, and then press the Enter key. USE DEFAULTS...
- Page 91 LM3210A Handling Instructions After the settings have been applied, Automatic Scan ￭ pressing the menu key once returns to the main menu, and pressing the key again With "AUTOMATIC SCAN", the 1-up display returns to the 1-up/4-up display screen. can be set to automatically scroll through the Note: selected parameters one by one.
- Page 92 LM3210A Handling Instructions Highlight "USE DEFAULTS", and then Custom Setup ￭ press the Enter key. With "CUSTOM SETUP", the type and number of parameters as well as their display order can be specified. Press the menu key. After the main menu...
- Page 93 LM3210A Handling Instructions Select the page. The parameters appear. The number at the right of the Check that the values for the four parameter indicates the location in the parameters are highlighted. 4-up display. 1=Upper left 2=Lower left 3=Upper right...
- Page 94 LM3210A Handling Instructions Check that a number appeared to the Check that the number at the right of right of the selected parameter. the parameter disappeared. ENGINE SPEED ENGINE SPEED DRIVERS DEMAND ENGINE TORQUE 4 DRIVERS DEMAND ENGINE TORQUE 4...
- Page 95 LM3210A Handling Instructions Use the arrow keys to highlight the item to Reset Reminders ￭ be changed, and then press the Enter key. A plus appears at the right of the currently With "RESET REMINDER", displayed selected items. remaining time can be reset to the time specified with "MODIFY REMINDERS".
- Page 96 LM3210A Handling Instructions Highlight "MODIFY REMINDERS", and Modify Reminders ￭ then press the Enter key. With "MODIFY REMINDERS", the replacement time period for consumables can be specified. The factory default replacement time periods RESET REMINDERS are the initial time periods.
- Page 97 LM3210A Handling Instructions Highlight the digit to be changed. Reminder Display ￭ Press the right arrow key to increase the number. Press the left arrow key to Important change the digit. If a warning message appears, immediately stop operation, and then perform the replacement procedure.
- Page 98 LM3210A Handling Instructions Select Units Units Monitor display S ENGLIS METRI METRI With "SELECT UNITS", the units of parameter C KPA C BAR values can be set to any of the following three ENG RPM formats. DEMAND TQ ％ ％...
- Page 99 LM3210A Handling Instructions SOFTWARE VERSION ･ Adjust Backlight FAULT CONVERSION ･ With "ADJUST BACKLIGHT", the brightness ANALOG INPUT ･ of the monitor display can be adjusted. ･ Press the right arrow key to make the display Note: brighter. Press the left arrow key to make the "GAGE DATA"...
- Page 100 LM3210A Handling Instructions Highlight "SET LOW FUEL LEVEL", and Fuel Level then press the Enter key. With "FUEL LEVEL", the low fuel level can be specified. Press the menu key. After the main menu appears, use the SET LOW FUEL LEVEL arrow keys to highlight "UTILITIES", and...
- Page 101 LM3210A Handling Instructions A warning mark appears in the upper- Low Fuel Level Display right corner of the monitor display. Caution If a warning message appears, immediately stop operation, and then supply fuel. 0 RPM 83 % When the fuel level falls below the...
- Page 102 LM3210A Handling Instructions Pressing the Enter key changes the screen Fault Code Displays from the fault code to the parameter display. Important Important If the service reminders are configured, the When the fault code (DTC) appears in the notices of the replacement time period for monitor display, contact your dealer.
- Page 103 LM3210A Handling Instructions Text 2 Text 2 ･ ･ The corrective action appears. The corrective action appears. 1 of 1 WARNING 1 of 1 WARNING SPN 916 FMI 17 SPN 110 FMI 3 CORRECTIVE ACTION: CORRECTIVE ACTION: S e e S e r v i c e M a n u a l S e e S e r v i c e M a n u a l <...
- Page 104 LM3210A Handling Instructions Engine warning lamp blinks when only DTC Engine Warning Lamp relevant to PCD/NCD come up. Important Make repairs immediately if the fault codes of PCD (Particulate Control Diagnostic) and NCD (NOx Control Diagnostic) appear. Engine warning lamp (LED) lights up or blinks when a failure occurs on the function of engine.
-
Page 105: Move
LM3210A Handling Instructions Move Important When towing the machine, travel at a speed Traveling Procedure no more than 3.0 km/h. In addition, do not tow the machine for more Caution than 3 minutes. Under any circumstances drive the machine at... -
Page 106: Cutting Work
LM3210A Handling Instructions Rear side Needle valve Replace the seat and close the cover. Remove the wheel stopper. Depress the brake pedal to release the parking brake. Warning While towing, always keep your foot on the brake pedal and depress the brake pedal at any time to stop. -
Page 107: Transporting
LM3210A Handling Instructions Shift the throttle knob to rev the engine up to the maximum rpm. Shift the mower unit up/down lever to the "Down" position to lower the mower units. Set the reel rotation switch to the "Rotation" position to rotate the reel cutters (cutting cylinders) of all mower units. - Page 108 LM3210A Handling Instructions Page 4-78 Storage...
-
Page 109: Maintenance
LM3210A Maintenance Maintenance Precautions ..... Page 5-2 Change of Engine Oil ......Page 5-44 Replacement of Engine Oil Filter ..Page 5-45 Maintenance Schedule ......Page 5-2 Replacement of Fuel Filter ....Page 5-45 Adjusted Value ........Page 5-7 Change of Fuse ........Page 5-46 DPF ............Page 5-8... -
Page 110: Maintenance Precautions
Use tools appropriate for each maintenance operation. Important For the safe and best performance of your machine, use Baroness genuine parts for replacement and accessories. Please note that our product warranty may be void if you use non-genuine parts for replacement or accessories. - Page 111 LM3210A Maintenance Maintenance Item Remarks Check oil or water leaks ○ Check cover condition ○ ...
- Page 112 LM3210A Maintenance Maintenance Item Remarks Clean air cleaner outer conditions than element (Replace the in normal ○ △ element after 6-time conditions cleaning) 100 hours first...
- Page 113 LM3210A Maintenance Maintenance Item Remarks Replace fuel filter △ cartridge Initial 50 hours, thereafter every 400 hours or Change engine oil ● △ △ ...
- Page 114 LM3210A Maintenance Maintenance Item Remarks defacement and joint ○ looseness) The secondary (inner) element Replace air cleaner should be *2.*4 △ ...
- Page 115 *1: When biodiesel fuel is used, change the fuel filter cartridge, fuel hose and clamp bands with new ･ ones at intervals half of the usual ones. *2: Consult your local Baroness Dealer or local KUBOTA Dealer for this service. ･ ･...
-
Page 116: Dpf
LM3210A Maintenance Automatic Regeneration About DPF Danger Danger The DPF is a purifying filter that collects PM Since it will become extremely hot around the (soot) from exhaust gas. exhaust outlet during DPF regeneration, do When a certain amount of PM (soot) has... - Page 117 LM3210A Maintenance Important If the regeneration remains uncompleted even after 30 minutes have passed since the start of automatic regeneration in PM accumulation 2400 RPM 100 % "Level 1", PM accumulation level enters ENG RPM % SOOT 65 C 40 % "Level 2".
- Page 118 LM3210A Maintenance Park this machine in a safe location. Important Apply the parking brake. If the regeneration remains uncompleted in Set the throttle opening to 0% (idling). automatic regeneration, parked regeneration Press the DPF parked regeneration switch. is required with the blinking regeneration icon.
- Page 119 LM3210A Maintenance Manual Regeneration Danger Danger 1 of 2 C : 1 Since it will become extremely hot around the SPN 3701 FMI 15 E x c e s s i v e P M 3 exhaust outlet during DPF regeneration, do not perform the regeneration in a location <...
- Page 120 LM3210A Maintenance ■In PM accumulation "Level 4": Contact your dealer for manual regeneration. Important Replacement of DPF If ignoring the manual regeneration requirement and continuing traveling or cutting When PM accumulates excessively in the DPF work in PM accumulation "Level 4", PM or ash accumulates, replace the DPF since the accumulation level enters "Level 5".
-
Page 121: Conditions For Dpf Regeneration
LM3210A Maintenance Park this machine in a safe location. Conditions for DPF Regeneration Apply the parking brake. Stop the engine. Danger Danger Contact your dealer for DPF replacement. Since it will become extremely hot around the ■In the case of "High frequency of exhaust outlet during DPF regeneration, do regeneration"：... -
Page 122: Pm Accumulation Level
LM3210A Maintenance <Automatic regeneration> PM Accumulation Level ■When the DPF auto regeneration inhibit switch set to the "Auto regeneration mode": Level 0 When the conditions for automatic DPF regeneration is not necessary. regeneration are met, the automatic Level 1 regeneration starts with the regeneration icon lighting. - Page 123 LM3210A Maintenance <Parked regeneration> Level 2 These are the conditions for activating ･ parked regeneration. Danger Danger The parking brake is applied. Since it will become extremely hot around the The traveling pedal is in neutral. exhaust outlet during DPF regeneration, do The throttle opening is 0% (idling).
- Page 124 LM3210A Maintenance When the regeneration completed, the <Parked regeneration> regeneration icon disappears. These are the conditions for activating ･ parked regeneration. The parking brake is applied. The traveling pedal is in neutral. The throttle opening is 0% (idling). 2400 RPM 100 % The blinking regeneration icon appears.
- Page 125 LM3210A Maintenance These are the statuses in PM accumulation Level 3 "Level 3". Danger Danger Since it will become extremely hot around the exhaust outlet during DPF regeneration, do 1 of 2 C : 1 not perform the regeneration in a location...
- Page 126 LM3210A Maintenance These are the statuses in PM accumulation Level 4 "Level 4". Danger Danger Since it will become extremely hot around the exhaust outlet during DPF regeneration, do not perform the regeneration in a location 1 of 2 C : 1...
-
Page 127: Jacking Up The Machine
LM3210A Maintenance Jacking Up The Machine Level 5 When PM accumulates excessively in the About Jacking Up The Machine DPF or ash accumulates, replace the DPF since the regeneration in that case is Warning prohibited. When replacing a tire or beginning any other You can not continue to use this machine ･... -
Page 128: Jacking Up The Machine
LM3210A Maintenance Front left frame Jack-Up Points rwyt62-075 Jack-Up Points_003 Center of pivot rwyt62-077 rwyt62-116 Jack-Up Points_004 Below rear wheel motors Jack-Up Points_001 There is one jack-up point below each rear Jack-up points wheel motor (left and right). Front right frame... -
Page 129: Greasing
LM3210A Maintenance Greasing No. of Location greasing About Greasing points Mower arm fulcrum Since there may be adhesion or damage due Lift arm fulcrum to lack of grease on moving parts, they must be greased. Brake lever shaft Add urea-based No. 2 grease in accordance Traveling pedal shaft fulcrum with the Maintenance Schedule. - Page 130 LM3210A Maintenance Lift arm fulcrum Brake lever shaft There is one greasing point on each lift arm There are two greasing points on the brake fulcrum connected to a mower unit. lever shaft. Lower the mower units before greasing the lift arm fulcrums.
- Page 131 LM3210A Maintenance Rear left wheel Reel housing There is one greasing point on the right and left housings of each mower unit. Hydraulic motor housing side 8bq62b-033 Type_F_010 Rear right wheel 8bq62b-179 Type_F_013 Caution Always use a hand operated grease gun and only add a maximum of 2 pumps of grease every 50 hours.
- Page 132 LM3210A Maintenance Rear roller Type_R There is one greasing point on the left and right of the rear roller of each mower unit. Grease nipples are installed in the following locations. Add grease every 50 hours of operation. 8bq62b-180 Type_F_015...
- Page 133 LM3210A Maintenance Mower arm fulcrum Mower units #2 and #3 There is one greasing point on each mower arm fulcrum connected to a mower unit. Grease mower units #2 and #3 in the swiveled position. "Swiveling Mower Units #2 and #3" (Page...
- Page 134 LM3210A Maintenance Traveling pedal shaft fulcrum Rear right wheel There are two greasing points on the traveling pedal shaft fulcrum. 8bq62b-034 Type_R_011 8bq62b-036 Neutral position area There are two greasing points on the Type_R_008 Pivot neutral position area. Middle between the rear wheels...
-
Page 135: Lubrication
LM3210A Maintenance Reel housing side Lubricating Points Type_F Apply lubricant at the following locations every 50 hours of operation. 8bq62b-386 Type_R_014 Rear roller There is one greasing point on the left and right of the rear roller of each mower unit. - Page 136 LM3210A Maintenance Mower cylinder spherical bearing Steering cylinder spherical bearing There are two points on each mower There are two points. cylinder. Mower cylinder #1 ysd2y4-023 Type_F_005 ysd2y4-020 Type_R Type_F_002 Apply lubricant at the following locations every Mower cylinder #2 and 3 50 hours of operation.
- Page 137 LM3210A Maintenance Mower cylinder spherical bearing Steering cylinder spherical bearing There are two points on each mower There are two points. cylinder. Mower cylinder #1 ysd2y4-023 Type_R_005 ysd2y4-020 Type_R_002 Mower cylinder #2 and 3 ysd2y4-021 Type_R_003 Mower cylinder #4 and 5...
-
Page 138: Maintenance Work
LM3210A Maintenance Have the following items ready: Strips of Maintenance Work newspaper, Abrasive [Back lapping powder mixed with oil; or gel compound (Baroness Cleaning of Mower Unit genuine abrasive)], Brush. Important While cleaning, do not allow water on the sealed parts of the reel shaft. (Avoid high- pressure water cleaning.) - Page 139 LM3210A Maintenance Set the reel rotation/stop switching lever to With the reel rotation/stop switching lever, the "Stop" position. adjust the rotation speed of the reel cutter (cutting cylinder). Apply the abrasive evenly with the brush on the top side of reel cutter (cutting cylinder) where the newspaper was cut well or of chalk-marked locations.
-
Page 140: Sharpening Of Reel Cutter
30 mm (1.18 in). cylindrical grinding to return it to a cylindrical shape. For sharpening the reel cutter (cutting cylinder), contact your dealer or Baroness unless you have a grinding machine. Caution Both the reel cutter (cutting cylinder) and the bed knife (bottom blade) are edged tools. -
Page 141: Replacement Of Reel Cutter
LM3210A Maintenance Sharpening is necessary when the reel cutter The criteria for replacing the reel cutter (cutting (cutting cylinder) reaches a condition described cylinder) are described below. below. However, these criteria are only a reference and do not guarantee performance like that of When the sharpening width (length of a new reel cutter (cutting cylinder). -
Page 142: Replacement Of Bed Knife
LM3210A Maintenance Note: High-speed-steel-tipped blade The outer diameter of the reel cutter (cutting Replace the bed knife (bottom blade) before it cylinder) shaft is 30 mm (1.18 in). no longer has a tip. d5gd5v-001 Replacement of Bed Knife (Bottom Blade)_001... -
Page 143: Swiveling Mower Units #2 And #3
LM3210A Maintenance Fully insert the grip pin into the locking hole Swiveling Mower Units #2 and #3 for maintenance, and then install the clip pin in the grip pin. Caution Both the reel cutter (cutting cylinder) and the bed knife (bottom blade) are edged tools. - Page 144 LM3210A Maintenance Removing/Installing Tires Rear tire Heat-treated bolt Front Tires Securely place the jack beneath the jack-up Follow the steps below to remove the front point below the rear wheel motor, and then tires: raise it until the tire lifts off the ground.
- Page 145 LM3210A Maintenance Adjustment of Brake Caution Make sure that the brake wire is not cracked or damaged. Important If the brake is not sufficiently effective due to a wider clearance gap between the brake disc mzdn8n-003 and the brake lining, adjust the clearance.
- Page 146 LM3210A Maintenance With the brake pedal released, obtain a play Adjustment bolt (on brake disc side) of 1.0 mm (0.039 in) at the joint part of the Lever inner wire. Open (neutral) Reduce the clearance by loosening the lock nut, then tightening the adjustment nut.
- Page 147 LM3210A Maintenance Break-In of Brakes Lever Seat If the brake shoes or brake pads are worn, replace them with new ones. Start the engine, and rev it up to the Immediately after replacement, drive to break maximum rpm. in the brakes if the effectiveness of the brakes Set the 2WD/4WD selector switch to the is low.
- Page 148 LM3210A Maintenance Change of Coolant LLC concentration Freezing temperature (volume %) Caution Down to -10 °C (14 °F) 20 % Down to -15 °C (5 °F) 30 % Do not touch the radiator or coolant during Down to -20 °C (-4 °F)
- Page 149 LM3210A Maintenance Remove the reserve tank. Change of Hydraulic Oil Caution Be careful with hot oil, which could cause burns if it contacts your skin. Important When you change the hydraulic oil, be sure to drain it into a bowl and discard it in ouuoov-024 accordance with local laws and regulations.
- Page 150 LM3210A Maintenance Open the tank cap, and then pour new oil Change of Hydraulic Oil Filter from the fill port until the oil level reaches the middle of the oil gauge on the hydraulic tank. Change of Hydraulic Oil Line Filter The hydraulic tank capacity is approximately 44.0 dm...
- Page 151 LM3210A Maintenance Firmly tighten the filter cartridge by hand Important until the packing contacts the mounting surface. Replace the intake port packing with a new And then tighten it with a half more turn. one. On a level surface, lower the mower units, and then stop the engine.
- Page 152 LM3210A Maintenance Check underneath the machine for Change the engine oil more frequently if the hydraulic oil leakage. engine oil is contaminated, or if you use the machine in dusty areas or operate the engine Install the left tank cover.
- Page 153 LM3210A Maintenance Make sure that there is no oil leakage at the Replacement of Engine Oil Filter sealing surface of the filter cartridge. Check the engine oil level. Caution If it is low, supply engine oil until it reaches Be careful with hot oil, which could cause the specified level.
- Page 154 LM3210A Maintenance Lightly coat the packing of the new cartridge with fuel, and then firmly hand- tighten the cartridge, without using the filter wrench. pkm25s-011 Fuse Box_001 Fuse box The machine uses a mini fuse for rvnnv5-002 automobiles. Replacement of Fuel Filter_002...
- Page 155 LM3210A Maintenance Fusible Link Fuse capacities of the fusible links are 30 A and 50 A. 1qgabk-009 Fusible Link_001 Fusible link (50 A) Fusible link (30 A) Maintenance Work Page 5-47...
- Page 156 LM3210A Maintenance Page 5-48 Maintenance Work...
- Page 160 1-26, Miyuki-cho, Toyokawa-city, Tel : +81 - 533 - 84 - 1390 Head Office Fax : +81 - 533 - 84 - 1220 Aichi-pref, 442-8530 JAPAN LM3210A-UM--GBZ/21C-00-S.K E02a[LM3210A_EU02a]...