Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ledj Spectra Par 7T3
Summary of Contents for Ledj Spectra Par 7T3
- Page 1 Spectra Par 7T3 Exterior Fixture User Manual Order code: LEDJ257...
-
Page 2: Safety Advice
• Always disconnect the power from the mains when product must be installed by a qualified technician in equipment is not in use or before cleaning! Only handle accordance with local territory regulations. The safety of the power-cable by the plug. Never pull out the plug by the installation is the responsibility of the installer. The pulling the power-cable. fixture presents risks of severe injury or death due to fire • Make sure that the available mains supply voltage is hazards, electric shock and falls. between 100~240V AC, 50/60Hz. • Warning! Risk Group 2 LED product according to • Make sure that the power cable is never crimped or EN 62471. Do not view the light output with optical damaged. Check the equipment and the power cable instruments or any device that may concentrate the beam. periodically. • WARRANTY: One year from date of purchase. • If the equipment is dropped or damaged, disconnect the mains power supply immediately and have a qualified engineer inspect the equipment before operating again. OPERATING DETERMINATIONS If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc. Do not endanger your own safety and the safety of others! Incorrect installation or use can cause serious damage to people and/or property. www.prolight.co.uk Spectra Par 7T3 User Manual... - Page 3 Product overview & technical specifications Spectra Par 7T3 Exterior Fixture IP66 The LEDJ Spectra Par 7T3 features a stylish and compact design. The fixture is suitable for architectural and stage lighting and can be used for both interior and exterior applications (IP66 rated). The housing is made of aluminium alloy and is gasket sealed. The unit is equipped with 7 x 3W tri-colour RGB LEDs and controlled via DMX or the optional IR remote control. • 7 x 3W tri-colour LEDs (RGB) • Optional LEDJ 1m Spectra Series Interior to Exterior • Beam angle: 28° DMX connection cable • 1155 Lux @ 2m (full on) available (Order code: LEDJ91) • 7.8kHz refresh rate • Optional IR remote: LEDJ90A • DMX channels: 1/3/4/5 or 6 selectable Specifications Spectra Par 7T3 • Static colour, colour fade, Power consumption colour change, colour mix, Power supply 100~240V, 50/60Hz auto and master/slave modes Dimensions 180 x 156 x 125 • 0 - 100% dimming Weight 1.6kg...
- Page 4 (0-100%) 069-091 Cyan 000-255 Strobe 092-114 Yellow Channel Value Function (slow-fast) 115-137 Orange 000-255 Red (0-100%) 138-160 Pink 000-255 Green (0-100%) 161-183 Purple 000-255 Blue (0-100%) 184-206 Dark Blue 000-255 Master dimmer 207-229 Pale Green (0-100%) 230-252 White 253-255 Warm White www.prolight.co.uk Spectra Par 7T3 User Manual...
- Page 5 (0-255 144-152 Magenta slow-fast) 153-161 Pink when 162-170 Light Pink channel 6 is set 171-179 Pastel Blue between 180-188 Pastel Green 026-255 189-197 Pastel Yellow 198-206 Pastel Purple 207-215 Pastel Cyan 216-224 Turquoise 225-233 Pastel Pink 234-242 Neutral White 243-251 Warm White 252-255 Cool White www.prolight.co.uk Spectra Par 7T3 User Manual...
-
Page 6: Master/Slave Mode
To set the slave unit, press the “M” button on the front g. 0 00~g. 2 55 G SLav of the master unit to show on the LED display. b. 0 00~b. 2 55 B The unit is now in Slave mode. Built-in programs Pr01~Pr07 To exit out of any of the above options, press the “M” button. Auto mode Auto Master/slave mode SLav Restore factory settings: DMX mode 1CH, 3CH, 4CH, To restore the unit back to its factory settings, 5CH, 6CH press the “M” and “E” buttons simultaneously. Address setting d001~d512 www.prolight.co.uk Spectra Par 7T3 User Manual... -
Page 7: Important Notes
• Now press the “2” button, and all the LEDs will • N ow press the “5” button, and all the LEDs will come on, the third digit 5 has been set. The full come on, the third digit 5 has been set. The full DMX address setting has been changed DMX address setting has been changed • N ow press the “DMX MODE” button to save • Now press the “DMX MODE” button to save the new address into memory the new address into the memory Important notes: • Set the DMX address on each fixture before plugging into the DMX controller • The IR remote cannot be used when the fixture(s) are being controlled with a DMX controller • The maximum IR transmitter distance is 10m - Please make sure that you have the IR remote aimed directly at the front panel of each fixture to be programmed • If you do not press the “DMX MODE” button after you have changed the DMX address when you power down the fixture it will lose the address you have set www.prolight.co.uk Spectra Par 7T3 User Manual... -
Page 8: Dmx Setup
DATA cable (DMX cable) requirements (for DMX operation): This fixture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit. Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight Concepts dealers. Please quote: LEDJ 1m Interior - LEDJ 1m Exterior LEDJ 2m Exterior LEDJ 5m Exterior LEDJ 10m Exterior Exterior DMX cable DMX cable DMX cable DMX cable DMX cable Order code: LEDJ91 Order code: LEDJ141 Order code: LEDJ142 Order code: LEDJ143 Order code: LEDJ144 LEDJ 1m Exterior LEDJ 2m Exterior LEDJ 5m Exterior LEDJ 10m Exterior LEDJ Spectra Series Power cable Power cable Power cable Power cable End Cap Set Order code: LEDJ146 Order code: LEDJ147 Order code: LEDJ148 Order code: LEDJ149 Order code: LEDJ93 www.prolight.co.uk Spectra Par 7T3 User Manual... -
Page 9: Line Termination
5-pin XLR (socket) 3-pin XLR (socket) Pin 1: GND (screen) Pin 1: GND (screen) Pin 2: Signal (-) Pin 2: Signal (-) Pin 3: Signal (+) Pin 3: Signal (+) Pin 4: N/C Pin 5: N/C www.prolight.co.uk Spectra Par 7T3 User Manual... -
Page 10: Weee Notice
WEEE notice Correct Disposal of this Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed of with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. www.prolight.co.uk Spectra Par 7T3 User Manual... - Page 11 Spectra Par 7T3 User Manual...
- Page 12 Spectra Par 7T3 User Manual...
Need help?
Do you have a question about the Spectra Par 7T3 and is the answer not in the manual?
Questions and answers