Discharging Lithium Battery; Voltage Balancing And Monitoring During The Discharge - RC-Plus PLUS POWER 80 Instruction Manual

DISCHARGING LITHIUM BATTERY

6.5 Discharging Lithium battery
6.5 Discharging Lithium battery

6.6 Voltage balancing and monitoring during the discharge

VOLTAGE BALANCING AND MONITORING DURING THE DISCHARGE
The processor monitors the voltage of individual cells during 'storage-mode' and
6.6 Voltage balancing and monitoring during the discharge
'discharge' of Lithium battery pack. It tries to normalise the voltages to be equal.
For this feature, the individual plug of the battry pack should be connected to the
The processor monitors the voltage of individual cells during 'storage-mode' and 'discharge' of Lithium battery pack. It
The processor monitors the voltage of individual cells during 'storage-mode' and
individual port of the charger.
tries to normalise the voltages to be equal. For this feature, the individual plug of the battery pack should be connected
'discharge' of Lithium battery pack. It tries to normalise the voltages to be equal.
If the voltage of any one or more cells varies abnormally during the procedure, It
to the individual port of the charger.
For this feature, the individual plug of the battry pack should be connected to the
terminates the process forcibly with the error massage. If this happens, the battery
If the voltage of any one or more cells varies abnormally during the procedure, It terminates the process forcibly with the
individual port of the charger.
pack contains the bad cell, or the bad connection of the cable plug. You can easily
error massage. If this happens, the battery pack contains the bad cell, or the bad connection of the cable plug. You can
If the voltage of any one or more cells varies abnormally during the procedure, It
know which one cell is bad by pressing INC button at time of showing the error
easily know which one cell is bad by pressing INC button at time of showing the error message.
terminates the process forcibly with the error massage. If this happens, the battery
message.
pack contains the bad cell, or the bad connection of the cable plug. You can easily
know which one cell is bad by pressing INC button at time of showing the error
message.
The value of discharge current on the left side of
The value of discharge current on the left side of screen may not exceed 1C
screen may not exceed 1C for a maximum safety
for a maximum safety and the final voltage on the right should not be under
and the final voltage on the right should not be under
the voltage level that is recommended by the battery manufacturer to avoid
The value of discharge current on the left side of
the voltage level that is recommended by the battery
deep discharging.
screen may not exceed 1C for a maximum safety
manufacturer to avoid deep discharging.
and the final voltage on the right should not be under
To start to discharge, press Start/ Enter key for more than 3 seconds.
To start to discharge, press Start/ Enter key for more
the voltage level that is recommended by the battery
than 3 seconds.
manufacturer to avoid deep discharging.
To start to discharge, press Start/ Enter key for more
This shows the present state of discharge. To stop
This shows the present state of discharge.
than 3 seconds.
discharging press Batt type/Stop key once.
To stop discharging Press Batt type/Stop key once.
This shows the present state of discharge. To stop
discharging press Batt type/Stop key once.
The processor found that the voltage of one of the cell
in the Lithium battery pack is too low.
The processor found that the voltage of one of the cell
The processor found that the voltage of one of the cell in the Lithium battery
in the Lithium battery pack is too low.
pack is too low.
In this case, the 5th cell is bad. If there happens the
connection-break of th cable or plug, the voltage value
may show zero.
In this case, the 5th cell is bad. If there happens the connection-break of the cable In this case, the 5th cell is bad. If there happens the
connection-break of th cable or plug, the voltage value
or plug, the voltage value may show zero.
may show zero.
16
12
- -