Lithium Battery (Lilo/Lipo/Life) Program; Charging Lithium Battery - RC-Plus PLUS POWER 80 Instruction Manual

6. Lithium battery(Lilo/LiPo/LiFe)program

LITHIUM BATTERY (LILO/LIPO/LIFE) PROGRAM

6. Lithium battery(Lilo/LiPo/LiFe)program
These programs are only suitable for charging and discharging Lithium batteries
These programs are only suitable for charging and discharging Lithium batteries with a nominal voltage of
with a nominal voltage of 3.3V, 3.6V and 3.7V per cell. These batteries need to
3.3V, 3.6V and 3.7V per cell. These batteries need to adopt different charge technique is termed a constant
These programs are only suitable for charging and discharging Lithium batteries
voltage(CV) and constant current(CC) method. The charge current varies according to the battery capacity
adopt different charge technique is termed a constant voltage(CV) and constant
with a nominal voltage of 3.3V, 3.6V and 3.7V per cell. These batteries need to
and performance. The final voltage of charge process is also very important; it should be precisely matched
current(CC) method. The charge current varies according to the battery capacity and
adopt different charge technique is termed a constant voltage(CV) and constant
with the charade voltage of the battery. They are 4.2V for LiPo, 4.1V for Lilo, and 3.6 V for LiFe. The charge
performance. The final voltage of charge process is also very important; it should be
current(CC) method. The charge current varies according to the battery capacity and
current and nominal voltage as for cell count set on the charge program must always be correct for the
precisely matched with the charade voltage of the battery. They are 4.2V for LiPo, 4.1V
performance. The final voltage of charge process is also very important; it should be
battery to be charged.
for Lilo, and 3.6 V for LiFe. The charge current and nominal voltage as for cell count
precisely matched with the charade voltage of the battery. They are 4.2V for LiPo, 4.1V
When you are willing to alter the parameter value in the program, press Start/Enter key to make it blink then
set on the charge program must always be correct for the battery to be charged.
for Lilo, and 3.6 V for LiFe. The charge current and nominal voltage as for cell count
change the value with INC or DEC key. The value will be stored by pressing Start/Enter key once.
When you are willing to alter the parameter value in the program, press Start/
set on the charge program must always be correct for the battery to be charged.
Enter key to make it blink then change the value with INC or DEC key. The value will
When you are willing to alter the parameter value in the program, press Start/
be stored by pressing Start/Enter key once.
Enter key to make it blink then change the value with INC or DEC key. The value will

CHARGING LITHIUM BATTERY

be stored by pressing Start/Enter key once.
6.1 Charging Lithium Battery
6.1 Charging Lithium Battery
L
L
This program sets the maximum charge capacity that will be supplied
to the battery during charge. If the delta-pack voltage is not detected
nor the safety timer expired by any reason, this feature will automati-
cally stop the process at the selected capacity value.
The beep sounds at every time pressing the buttons to confirm your
action. The beep or melody sounded at various times during operation
to alert different mode changes. These audible sounds can be on or off.
This program monitors the voltage of input battery. If the voltage drops
below the value you set the operation forcibly terminated to protect
the input battery.
The left side of the first line shows the type of battery
The left side of the first line shows the type of battery you select at the users
you select at the users setting. The value on the left
setting. The value on the left side of second line sets a charge current and the
The left side of the first line shows the type of battery
side of second line sets a charge current and the value
value on the right side of second line sets the voltage of the battery pack.
you select at the users setting. The value on the left
on the right side of second line sets the voltage of the
After setting the current and voltage press Start/Enter key for more than 3
side of second line sets a charge current and the value
battery pack.
seconds to start the process.
on the right side of second line sets the voltage of the
After setting the current and voltage press Start/Enter
(Charge current:0.1~7.0A,Voltage:1~6 series)
battery pack.
key for more than 3 seconds to start the process.
After setting the current and voltage press Start/Enter
(Charge current:0.1~7.0A,Voltage:1~6 series)
key for more than 3 seconds to start the process.
13
(Charge current:0.1~7.0A,Voltage:1~6 series)