Charging Lithium Battery At Balance Mode - RC-Plus PLUS POWER 80 Instruction Manual

6.2 Charging Lithium battery at balance mode

This is for balancing the voltages of Lithium batteries of the battery park to be
6.2 Charging Lithium battery at balance mode
charged. The battery pack to be charged should be connected to the suitable balance CHARGING LITHIUM BATTERY AT BALANCE MODE
This is for balancing the voltages of Lithium batteries of the battery park to be
port at the right side of the charger. And also, you need to connect the battery output
charged. The battery pack to be charged should be connected to the suitable balance
This is for balancing the voltages of Lithium batteries of the battery park to be charged. The battery pack to be charged
plug to the output of charger.
port at the right side of the charger. And also, you need to connect the battery output
should be connected to the suitable balance port at the right side of the charger. And also, you need to connect the
In this mode, the charging process will be different from ordinary charging mode.
plug to the output of charger.
battery output plug to the output of charger.
The internal processor of the charger will monitor the voltages of each cell of the
In this mode, the charging process will be different from ordinary charging mode. The internal processor of the charger In this mode, the charging process will be different from ordinary charging mode.
battery pack and controls charging current that is feeding to each cell to normalise
will monitor the voltages of each cell of the battery pack and controls charging current that is feeding to each cell to
The internal processor of the charger will monitor the voltages of each cell of the
the voltage.
normalise the voltage.
battery pack and controls charging current that is feeding to each cell to normalise
the voltage.
Balance
Balance
This shows the number of cells you set up and the
processor detects. ' R: ' shows the number of cells
This shows the number of cells you set up and the
found by the charger and ' S:' is the number of This shows the number of cells you set up and the processor detects. ' R: '
processor detects. ' R: ' shows the number of cells
shows the number of cells found by the charger and ' S:' is the number of cells
cells selected by you at the previous screen. If both
found by the charger and ' S:' is the number of
selected by you at the previous screen. If both numbers are identical you can
numbers are identical you can start charging by press
cells selected by you at the previous screen. If both
start charging by press Start/Enter button. If not, press Batt Type/Stop button
Start/Enter button. If not, press Batt Type/Stop button
numbers are identical you can start charging by press
to go back to previous screen. Then carefully check the number of cells of the
to go back to previous screen. Then carefully check
Start/Enter button. If not, press Batt Type/Stop button
battery pack to charge again.
the number of cells of the battery pack to charge again.
to go back to previous screen. Then carefully check
the number of cells of the battery pack to charge again.
The screen shows the present situation during charge
process. To stop charging press Batt Type/Stop key
The screen shows the present situation during charge process. To stop charging
The screen shows the present situation during charge
once.
press Batt Type/Stop key once.
process. To stop charging press Batt Type/Stop key
once.
The value on the left side of second line sets a charge
The value on the left side of second line sets a charge current and the
current and the value on the right side of second line
value on the right side of second line sets the voltage of the battery pack.
The value on the left side of second line sets a charge
sets the voltage of the battery pack.
After setting the current and voltage press Start/ Enter key for more than 3
current and the value on the right side of second line
After setting the current and voltage press Start/ Enter
seconds to start the process.
sets the voltage of the battery pack.
key for more than 3 seconds to start the process.
(Charge current:0.1~7.0A, Voltage:1~6 series)
After setting the current and voltage press Start/ Enter
(Charge current:0.1~7.0A, Voltage:1~6 series)
key for more than 3 seconds to start the process.
(Charge current:0.1~7.0A, Voltage:1~6 series)
This shows the number of cells you set up and the
This shows the number of cells you set up and the processor detects.' R: '
processor detects.' R: ' shows the number of cells found
shows the number of cells found by the charger and ' S:' is the number of
This shows the number of cells you set up and the
by the charger and ' S:' is the number of cells selected
cells selected by you at the previous screen. If both numbers are identical
processor detects.' R: ' shows the number of cells found
by you at the previous screen. If both numbers are
you can start charging by press Start /Enter button. If not, press Batt type/
by the charger and ' S:' is the number of cells selected
identical you can start charging by press Start /Enter
Stop button to go back to previous screen. Then carefully check the num-
by you at the previous screen. If both numbers are
button. If not, press Batt type/Stop button to go back
identical you can start charging by press Start /Enter ber of cells of the battery pack to charge again.
to previous screen. Then carefully check the number of
button. If not, press Batt type/Stop button to go back
cells of the battery pack to charge again.
to previous screen. Then carefully check the number of
The screen shows the present situation during charge
cells of the battery pack to charge again.
process. To stop charging press Batt type/Stop key
The screen shows the present situation during charge process. To stop
The screen shows the present situation during charge
once.
charging press Batt type/Stop key once.
process. To stop charging press Batt type/Stop key
once.
10
- -
14
10
- -