Table of Contents
Advertisement
2.6.4
Shut-Down Procedure
1. Flip main power switch to "
matic steam generator system, it will drain itself.
2. Check that all timer dials are in the "
3. Leave the cooking compartment doors slightly ajar
to extend the life of the door gaskets.
2.7 REVERSING THE DOORS
The Pressureless Steam Cooker has a reversible
cooking compartment door. This section contains instruc-
tions for reversing this door.
1. Turn off the power to unit.
2. Open the cooking compartment door.
3. Remove the two screws that attach the top hinge
to the front of the unit.
4. Slide the door upward, off the bottom hinge.
5. Remove the two screws that attach the bottom
hinge to the front of the unit.
6. Remove the right and left side panels by unscrew-
ing one screw on each panel and sliding the panel
down..
7. Remove the door interlock assembly by unscrew-
ing the two nuts that hold it in place (assembly is
attached to the screws in the top right hinge mount-
ing holes, see fig 2-1).
8. Remove the four screws in the right side hinge
mounting holes and install them in the left side
hinge mounting holes (where the hinges were origi-
nally mounted).
9. Using the nuts removed in step #6, reinstall the
door interlock assembly onto the 2 (two) screws in
the lower left hinge mounting holes (See Fig 2.1)
by moving the assembly over the cooking com-
partment to the other side of the unit. Rotate the
door interlock assembly 180
so that the switch is now facing up..
10. Reinstall for the top hinge and screw into the right
lower hinge mounting holes. Rotate the hinge 180
for installation, so that the pin which the door
rides on is now facing up. The hinge must be ro-
tated because it will now function as the bottom
hinge. DO NOT COMPLETETLY TIGHTEN THE
HINGE MOUNTING SCREWS YET. These will be
used later for adjusting the door.
Form No. S-4846 Rev. A 11/98
2. INSTALLATION (cont'd.)
." As this is an auto-
OFF
" position.
OFF
o
for installation,
11. Remove the door latch assembly form the face of
the unit. The two (2) nuts mounting the door latch
are located behind the face of the unit and must be
accessed where the rightside panel was removed.
12. Remove the two (2) white hole plugs from the left
door latch mounting holes, and insert them into the
right door latch mounting holes (where the door latch
assembly was originally mounted ).
13. Rotate the door latch assembly 180
into the left door latch mounting holes.
NOTE: Each stud on the latch assembly should have a
plastic washer, a spring, a plastic washer and a
Nyloc type nut.
14. To adjust the tensionof the door latch, tighten both
nuts down until the springs are fully compressed,
then back each nut of 1 1/2 turns.
15. Rotate the hinge 180
16. Slide the remaining hinge into the top door bear-
ing..
17. Slide the door and hinge assembly down onto the
hinge which you have already mounted to the front
of the unit. Use the two screws to mount the top
hinge into the right upper hinge mounting holes.
DO NOT COMPLETELY TIGHTEN THE HINGE
MOUNTING SCREWS YET.
18. Slowly push the cooking compartment door closed
until it is latched.
19. The cooking compartment door can be raised, low-
ered, and/or rotated into position by bumping it with
the palm of your hand or by using a small rubber
mallet.
20. First, check the alignment at the front of the door
by making sure that the striker in the door is cen-
tered with the latch mechanism on the front of the
unit.
21. Square the door to the unit by raising or loweringthe
hinge side of the door, keeping the latch centered
with the striker.
22. Visually inspect the door. Be sure that the door is
square to the unit, the striker is centered with the
latch, and the gasket is in contact with the entire
lip of the cooking compartment.
23. Gently open the cooking compartment door, taking
o
care not to move it out of position.
24. Tighten all four (4) door hinge bracket mounting
screws.
25. Close and visually inspect the door again, as de-
scribed in step #22.
26. Reinstall the left and right panels, using the screws
for each panel.
2-3
o
, and install
o
for mounting.
Advertisement
Table of Contents
