Related Manuals for IBASE Technology CSB200-822
Summary of Contents for IBASE Technology CSB200-822
- Page 1 CSB200-822 Fanless System with 3.5” Disk-Size SBC User’s Manual Version 1.0 (Feb. 2019)
- Page 2 No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”).
-
Page 3: Compliance
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm). • Lead (Pb) • Mercury (Hg) • Cadmium (Cd) • Hexavalent chromium (Cr6+) • Polybrominated biphenyls (PBB) • Polybrominated diphenyl ether (PBDE) CSB200-822 User Manual... -
Page 4: Important Safety Information
Do not disassemble, repair or make any modification to the device. Disassembly, modification, or any attempt at repair could generate hazards and cause damage to the device, even bodily injury or property damage, and will void any warranty. CSB200-822 User Manual... -
Page 5: Caution
Software in use (such as OS and application software, including the version numbers) 3. If repair service is required, you can download the RMA form at http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and contact your distributor or sales representative. CSB200-822 User Manual... -
Page 6: Table Of Contents
LVDS Panel Brightness Selection (JP1) ....... 18 2.4.2 LVDS Panel Power Selection (JP2) ........19 2.4.3 eDP Panel Power Selection (JP3) ........19 2.4.4 eDP / LVDS Panel Selection (JP4) ........20 2.4.5 Clearing CMOS Data (JP5) ..........20 CSB200-822 User Manual... - Page 7 M.2 Setup ................51 4.4.7 CPU Configuration ..............52 4.4.8 AMI Graphic Output Protocol Policy ........53 4.4.9 Network Stack Configuration ..........54 4.4.10 CSM Configuration ..............55 4.4.11 USB Configuration ..............56 Chipset Settings ..................57 CSB200-822 User Manual...
- Page 8 Security Settings ................... 61 4.6.1 Secure Boot ................62 Boot Settings..................64 Save & Exit Settings................65 Appendix ...................... 66 I/O Port Address Map ................67 Interrupt Request Lines (IRQ) ............... 69 Watchdog Timer Configuration .............. 70 viii CSB200-822 User Manual...
-
Page 9: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Optional Accessories • Specifications • Overview • Dimensions... -
Page 10: Introduction
1.1 Introduction The CSB200-822 is a compact and fanless design applicable to thin clients, smart industrial automation or controller, and retail equipment. This product ® ® ® comes with an Intel Pentium J5005 QC or Celeron J4005 DC processor and features iSmart, the IBASE’s unique technique, which allows the device capable of auto-scheduling for general applications and gives energy savings on power. -
Page 11: Packing List
• DVD Disk (including drivers and this user manual) Motherboard IB822 User’s Manual • (You can download CSB200-822 User’s Manual from our website.) 1.4 Optional Accessories IBASE provide optional accessories as follows. Please contact us or your dealer if you need any. -
Page 12: Specifications
CE / FCC Class B / LVD I/O Ports 12V DC-in through a 3-pin terminal block DC Input (Optional: a locking DC Jack) 2 x RJ45 GbE LAN • 2 x USB 2.0 • 4 x USB 3.0 CSB200-822 User Manual... - Page 13 Operating: 0.25 Grms / 5 ~ 500 Hz Vibration • Protection Non-operating: 1 Grms / 5 ~ 500Hz • Operating: 20 g / 11 ms Shock • Protection Non-operating: 40 g / 11 ms All specifications are subject to change without prior notice. CSB200-822 User Manual...
-
Page 14: Overview
Antenna Hole USB 2.0 Ports Wall Mounting Kit (2 brackets) Rear View No. Name Name 3-Pin DC-In Power Connector HDMI Port USB 3.0 Ports COM1 RS-232/422/485 Port GbE LAN Ports COM2 ~ COM4 RS-232 Ports DisplayPort Antenna Holes CSB200-822 User Manual... -
Page 15: Dimensions
General Information Oblique View 1.7 Dimensions Unit: mm CSB200-822 User Manual... -
Page 16: Chapter 2 Hardware Configuration
Chapter 2 Hardware Configuration The information provided in this chapter includes: • Installations • Information and locations of connectors... -
Page 17: Installations
1. Loosen the 3 screws to free up interior plate. 2. Take out the interior plate along with the small PCB and I/O module carefully. 3. Align the key of your memory module with that on the memory slot and insert the module slantwise. CSB200-822 User Manual... -
Page 18: Card Installation / Replacement
2.1.2 M.2 Card Installation / Replacement If you are using a model type of CSB200-822 that doesn’t include any M.2 card, you will have to remove the interior plate carrying a small PCB with I/O module locating above the M.2 slots as shown below. Follow the instructions to remove the plate. -
Page 19: Hdd/Ssd Installation / Replacement
3. Unplug all the SATA cables if a HDD/SSD is pre-installed. 4. Attach a new HDD/SSD and tighten these screws to fix the HDD/SSD. Then connect the SATA cables. 5. Secure the plate along with the new HDD/SSD back to the system. CSB200-822 User Manual... -
Page 20: Card Installation
1. Thread and fasten the hex nut and the 2. Apply adhesive around here. washer. Then install the antenna. Info: The diameter of the nut is around 6.35 mm (0.25”-36UNC). CSB200-822 User Manual... -
Page 21: Mounting Installation
1. Attach the mounting kit (2 brackets) to the your product, and secure with the supplied four screws as below. 2. Then prepare at least four screws (M3, 6 mm) to mount the device on wall . CSB200-822 User Manual... -
Page 22: Pinout For Com Ports & Dc Power Connectors
DCD, Data carrier detect DSR, Data set ready RXD, Receive data RTS, Request to send TXD, Transmit data CTS, Clear to send DTR, Data terminal ready RI, Ring indicator Ground Assignment RS-232 RS-422 RS-485 DATA- DATA+ Ground Ground Ground CSB200-822 User Manual... - Page 23 DSR, Data set ready RXD, Receive data RTS, Request to send TXD, Transmit data CTS, Clear to send DTR, Data terminal ready RI, Ring indicator Ground • DC Power Input Connector (terminal block) ➔ Assignment Assignment Ground +12V Chassis Ground CSB200-822 User Manual...
-
Page 24: Setting The Jumpers
1 2 3 When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e. turned On. When a jumper cap is removed from two jumper pins, this jumper is open, i.e. turned Off. CSB200-822 User Manual... -
Page 25: Jumper & Connector Locations On Motherboard
Hardware Configuration 2.3 Jumper & Connector Locations on Motherboard Motherboard: IB822 Board diagram of IB822 CSB200-822 User Manual... -
Page 26: Jumpers Quick Reference
Panel Power Selection eDP / LVDS Panel Seelction Clearing CMOS Data Clearing ME Register ATX / AT Power Selection Factory Use Only JP7, JP9 2.4.1 LVDS Panel Brightness Selection (JP1) Function Pin closed Illustration 3.3V (default) CSB200-822 User Manual... -
Page 27: Lvds Panel Power Selection (Jp2)
Hardware Configuration 2.4.2 LVDS Panel Power Selection (JP2) Function Pin closed Illustration 3.3V (default) 2.4.3 eDP Panel Power Selection (JP3) Function Pin closed Illustration 3.3V (default) CSB200-822 User Manual... -
Page 28: Edp / Lvds Panel Selection (Jp4)
2.4.4 eDP / LVDS Panel Selection (JP4) Function Pin closed Illustration LVDS (default) 2.4.5 Clearing CMOS Data (JP5) Function Pin closed Illustration Normal (default) Clear CMOS CSB200-822 User Manual... -
Page 29: Clearing Me Register (Jp6)
Hardware Configuration 2.4.6 Clearing ME Register (JP6) Function Pin closed Illustration Normal (default) Clear ME 2.4.7 ATX / AT Power Selection (JP8) Function Pin closed Illustration (default) CSB200-822 User Manual... -
Page 30: Connectors Quick Reference
CN5, CN6 DisplayPort HDMI Port DDR4 SO-DIMM Slot J5, J7 M.2 E2230 Slot J12 (shared with M.2 B2242 Slot CN3) Factory Use Only J15, J16 [1]: Refer to 2.1.7 Pinout for COM Ports & DC Power Connectors. CSB200-822 User Manual... -
Page 31: Edp Connector (Cn1)
Hardware Configuration 2.5.1 eDP Connector (CN1) Assignment Assignment Ground BL_Power BL_Power Panel_VDD BL_Power Panel_VDD BL_Power Ground AUX_N AUX_P BRIGHTNESS Ground Bklt_en TX0_P Ground TX0_N Ground Ground Ground TX1_P Ground TX1_N Ground Ground CSB200-822 User Manual... -
Page 32: Lcd Backlight Connector (J2)
LCD Backlight Connector (J2) Assignment Assignment +12V Brightness Control Backlight Enable Ground 2.5.3 LVDS Connector (J1, J3) Assignment Assignment TX0P TX0N Ground Ground TX1P TX1N Ground Ground TX2P TX2N Ground Ground CLKP CLKN Ground Ground TX3P TX3N CSB200-822 User Manual... -
Page 33: Audio Connector (J4)
Hardware Configuration 2.5.4 Audio Connector (J4) Assignment Assignment Lineout_L Lineout_R JD_FRONT Ground LINEIN_L Linein_R JD_LINEIN Ground MIC_L MIC-R JD_MIC1 Ground 2.5.5 USB 2.0 Connector (J8) Assignment Assignment Ground Ground CSB200-822 User Manual... -
Page 34: Amplifier Connector (J6)
2.5.6 Amplifier Connector (J6) Assignment Assignment OUTL+ OUTR- OUTL- OUTR+ 2.5.7 SATA HDD Power Connector (J11) Assignment Assignment Ground Ground +12V CSB200-822 User Manual... -
Page 35: Front Panel Connector (J13)
Orientation is not required when making a connection to this header. • Power LED: Pins 7 and 8 This connector connects to the system power LED on control panel. This LED will light when the system turns on. CSB200-822 User Manual... -
Page 36: Digital I/O Connector (J19)
2.5.9 Digital I/O Connector (J19) Assignment Assignment Ground OUT3 OUT1 OUT2 OUT0 2.5.10 DC Power Input Connector (J20) Assignment Assignment +12V ~ +24V Ground CSB200-822 User Manual... -
Page 37: Battery Connector (Bat1)
Hardware Configuration 2.5.11 Battery Connector (BAT1) Assignment Assignment Battery+ Ground CSB200-822 User Manual... -
Page 38: Chapter 3 Driver Installation
Chapter 3 Driver Installation The information provided in this chapter includes: • ® Intel Chipset Software Installation Utility • Graphics Driver • HD Audio Driver • ® Intel Trusted Execution Engine • ® Intel Serial I/O Drivers • LAN Driver... -
Page 39: Introduction
Intel(R) Gemini Lake Chipset Drivers on the right pane. 2. Click Intel(R) Chipset Software Installation Utility. ® 3. When the Welcome screen to the Intel Chipset Device Software appears, click Next to continue. 4. Accept the software license agreement and proceed with the installation process. CSB200-822 User Manual... - Page 40 5. On the Readme File Information screen, click Next for installation. 6. When the driver is completely installed, restart the computer for changes to take effect. CSB200-822 User Manual...
-
Page 41: Graphics Driver Installation
2. Click Intel(R) Gemini Lake Graphics Driver. 3. When the Welcome screen appears, click Next. 4. Click Yes to accept the license agreement and click Next. until installation starts 5. When the driver is completely installed, restart the computer. CSB200-822 User Manual... -
Page 42: Hd Audio Driver Installation
3. On the Welcome screen of the InstallShield Wizard, click Next until the installation starts. 4. Click Next until the installation starts. 5. When the driver is completely installed, restart the computer for changes to take effect. CSB200-822 User Manual... -
Page 43: Intel Trusted Execution Engine Drivers Installation
1. Click Intel on the left pane and then Intel(R) Gemini Lake Chipset Drivers. 2. Click Intel(R) TXE Drivers. 3. When the Welcome screen appears, click Next to continue. 4. Accept the licence agreement and click Next. 5. Click Next for installation. CSB200-822 User Manual... - Page 44 6. As the driver has been successfully installed, restart the computer for changes to take effect. CSB200-822 User Manual...
-
Page 45: Intel Serial I/O Drivers
3. As the Welcome screen to the InstallShield Wizard appears, click Next. 4. Accept the licence agreement and click Next. 5. After reading the Readme File, click Next until installation starts. 6. As the driver has been successfully installed, restart the computer for changes to take effect. CSB200-822 User Manual... -
Page 46: Lan Driver Installation
1. Click LAN Card on the left pane and then Intel(R) LAN Controller Drivers on the right pane. 2. Click Intel(R) I21x Gigabit Network Drivers.. 3. When the Welcome screen appears, click Next. 4. Accept the license agreement and click Next. CSB200-822 User Manual... - Page 47 5. On the Setup Options screen, tick the checkbox to select the desired driver(s) for installation. Then click Next to continue. 6. When the wizard is ready for installation, click Install. 7. As the installation is complete, restart the computer for changes to take effect. CSB200-822 User Manual...
-
Page 48: Chapter 4 Bios Setup
Chapter 4 BIOS Setup This chapter the different settings available in the AMI describes BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Security Settings •... -
Page 49: Introduction
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. CSB200-822 User Manual... -
Page 50: Main Settings
4.3 Main Settings BIOS Setting Description System Date Sets the date. Use the <Tab> key to switch between the data elements. System Time Set the time. Use the <Tab> key to switch between the data elements. CSB200-822 User Manual... -
Page 51: Advanced Settings
4.4.1 ACPI Settings BIOS Setting Description ACPI Sleep State Selects an ACPI sleep state (Suspend Disabled or S3) where the system will enter when the Suspend button is pressed. CSB200-822 User Manual... -
Page 52: Lvds (Edp/Dp) Configuration
1600 x 1200 / 1680 x 1050 / 1920 x 1080 / 1920 x 1200 Signal Type Allows you to select PWM or DC mode. Brightness Percent Options: 100%, 90%, 75%, 60%, 45%, 30%, 20%, 10% PWM Clock Options: 200 Hz, 1KHz, 5KHz CSB200-822 User Manual... -
Page 53: Ismart Controller
Temperature Guardian Generate the reset signal when system hands up on POST. Schedule Slots Sets up the hour / minute / day for the power- on schedule for the system. Options: None, Power On, Power On/Off CSB200-822 User Manual... -
Page 54: Fintek Super Io Configuration
Options: All Enable / Enable Ethernet for WOL / All Disable Serial Ports Configuration Sets parameters of serial ports. Enables / Disables the serial port and select an optimal setting for the Super IO device. CSB200-822 User Manual... - Page 55 IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 Device Mode Changes the serial port mode to: • RS232 • RS485 TX Low Active • RS485 with Termination TX Low Active • RS422 • RS422 with Termination CSB200-822 User Manual...
- Page 56 IO = 2F8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 3E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 CSB200-822 User Manual...
- Page 57 IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2F0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2E0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 CSB200-822 User Manual...
- Page 58 IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2F0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2E0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 CSB200-822 User Manual...
-
Page 59: Fintek Super Io Hardware Monitor
Sets a threshold of temperature to shut down if Temperature CPU goes overheated. Options: Disabled / 70°C / 75°C / 80°C / 85°C / 90°C / 95°C 4.4.6 M.2 Setup BIOS Setting Description M.2 Select Selects the M.2 interface as SATA or PCIe. CSB200-822 User Manual... -
Page 60: Cpu Configuration
Allows you to enable / disable Turbo Mode. Active Processor Cores Enables / Disables the cores in the processor package. Intel Virtualization When enabled, a VMM can utilize the Technology additional hardware capabilities provided by Vanderpool Technology. VT-d Enables / Disables CPU VT-d. CSB200-822 User Manual... -
Page 61: Ami Graphic Output Protocol Policy
4.4.7.2. CPU Power Management Information BIOS Setting Description EIST Enables / Disables Intel SpeedStep. Turbo Mode Enables / Disables the turbo mode. 4.4.8 AMI Graphic Output Protocol Policy BIOS Setting Description Output Select Outputs through HDMI1 interface. CSB200-822 User Manual... -
Page 62: Network Stack Configuration
If disabled, Ipv4 HTTP boot option will not be created. PXE boot wait time Assigns a period of time to press ESC key to abort the PXE boot. Media detect count Assigns a number of times to check the presence of media. CSB200-822 User Manual... -
Page 63: Csm Configuration
Options: Adjust, Keep Boot option filter Controls the priority of Legacy and UEFI ROMs. Options: UEFI and Legacy, Legacy only, UEFI only Network Controls the execution of UEFI and Legacy Network OpROM. Options: Do not launch, UEFI, Legacy CSB200-822 User Manual... -
Page 64: Usb Configuration
The maximum time the device will take before it properly reports itself to the Host Controller. Auto uses default value for a Root port it is 100ms. But for a Hub port, the delay is taken from Hub descriptor. CSB200-822 User Manual... -
Page 65: Chipset Settings
Configures HD-audio configuration settings. Configuration PCI Express Controls the PCI Express root port. Configuration SATA Drives Determines how SATA controller(s) operate. Configures XHCI pre-boot driver, XHCI mode, USB VBUS, USB Configuration HSIC1, USB disable override, XDCI and XHCI. CSB200-822 User Manual... - Page 66 Options: Disable / L0s / L1 / L0SL1 / Auto L1 Substates Sets PCIe L1 substates. Options: Disables / L1.1 / L1.2 / L1.1 & L1.2 PME SCI Enables / Disables PME SCI. PCIe Speed Configures the PCIe speed. Options: Auto, Gen1, Gen2 CSB200-822 User Manual...
- Page 67 BIOS Setup 4.5.1.3. SATA Drivers BIOS Setting Description SATA Mode Selection Determines how SATA controller(s) operate. SATA Port 0 / 1 Enables / Disables SATA port 0 or port 1. CSB200-822 User Manual...
- Page 68 USB port from reporting a device connection to the controller. XDCI Support Enables / Disables XDCI. XHCI Disable FALSE makes the XHCI Link Compliance Compliance Mode Mode not disabled. TRUE disables the XHCI Link Compliance Mode. CSB200-822 User Manual...
-
Page 69: Security Settings
Sets an administrator password for the setup Password utility. User Password Sets a user password. Secure Boot Activates when: secure Boot is enabled, Platform Key (PK) is enrolled, System mode is user / depolyed, and CSM is disabled. CSB200-822 User Manual... -
Page 70: Secure Boot
Customizable Secure Boot mode: In Custom mode, Secure Boot Customization polocy variables can be configured by a physically present user without full authentication. Restore Force System to User Mode. Configure NVRAM to contain OEM- Factory Keys defined factory default Secure Boot keys. CSB200-822 User Manual... - Page 71 1.) Public Key Certificate in: Forbidden Signatures / EFI_SIGNATURE_LIST / EFI_CERT_XS09 Authorized TimeStamps / (DER encoded) / EFI-CERT_RSA2048 (bin) OsRecovery Signatures / EFI_CERT_SHA256,384,512 2.) Authenticated UEFI Variable 3.) EFI PE/COFF Image (SHA256) Key source: factory, external, mixed CSB200-822 User Manual...
-
Page 72: Boot Settings
Controls the placement of newly detected UEFI boot options. Options: Default, Place First, Place Last Boot mode select Selects a Boot mode, Legacy / UEFI / Dual. Boot Option Priorities Sets the system boot order priorities for hard disk, CD/DVD, USB, Network. CSB200-822 User Manual... -
Page 73: Save & Exit Settings
Restore Defaults Restores / Loads defaults values for all the setup options. Save as User Defaults Saves the changes done so far as User Defaults. Restore User Defaults Restores the user defaults to all the setup options. CSB200-822 User Manual... -
Page 74: Appendix
Appendix This section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration. • I/O Port Address Map • Interrupt Request Lines (IRQ) • Watchdog Timer Configuration... -
Page 75: I/O Port Address Map
SMBUS - 5AD4 Intel(R) Celeron(R)/Pentium(R) Processor 0x0000D000-0x0000DFFF PCI Express Root Port - 5AD9 0x000003F8-0x000003FF Communications Port (COM1) 0x000002F8-0x000002FF Communications Port (COM2) 0x000003E8-0x000003EF Communications Port (COM3) 0x000002E8-0x000002EF Communications Port (COM4) 0x0000E000-0x0000EFFF Intel(R) Celeron(R)/Pentium(R) Processor PCI Express Root Port - 5AD8 CSB200-822 User Manual... - Page 76 0x000000B8-0x000000B9 Programmable interrupt controller 0x000000BC-0x000000BD Programmable interrupt controller 0x000004D0-0x000004D1 Programmable interrupt controller 0x0000F000-0x0000F03F Intel(R) HD Graphics 0x0000F090-0x0000F097 Standard SATA AHCI Controller 0x0000F080-0x0000F083 Standard SATA AHCI Controller 0x0000F060-0x0000F07F Standard SATA AHCI Controller 0x00000040-0x00000043 System timer 0x00000050-0x00000053 System timer CSB200-822 User Manual...
-
Page 77: Interrupt Request Lines (Irq)
IRQ 4294967280 ~ Intel(R) I211 Gigabit Network Connection #2 IRQ 4294967285 IRQ 4294967286 ~ Intel(R) I211 Gigabit Network Connection IRQ 4294967291 IRQ 4294967292 Intel(R) Trusted Execution Engine Interface IRQ 4294967293 Intel(R) HD Graphics IRQ 4294967294 Standard SATA AHCI Controller CSB200-822 User Manual... -
Page 78: Watchdog Timer Configuration
**endptr; char SIO; printf("Fintek 81964 watch dog program\n"); SIO = Init_F81964(); if (SIO == 0) printf("Can not detect Fintek 81964, program abort.\n"); return(1); }//if (SIO == 0) if (argc != 2) printf(" Parameter incorrect!!\n"); return (1); CSB200-822 User Manual... - Page 79 //--------------------------------------------------------------------------- void DisableWDT(void) unsigned char bBuf; Set_F81964_LD(0x07); //switch to logic device 7 bBuf = Get_F81964_Reg(0xFA); bBuf &= ~0x01; Set_F81964_Reg(0xFA, bBuf); //disable WDTO output bBuf = Get_F81964_Reg(0xF5); bBuf &= ~0x20; bBuf |= 0x40; Set_F81964_Reg(0xF5, bBuf); //disable WDT //--------------------------------------------------------------------------- CSB200-822 User Manual...
- Page 80 (ucDid == 0x07) //Fintek 81964 goto Init_Finish; } F81964_BASE = 0x00; result = F81964_BASE; Init_Finish: return (result); //--------------------------------------------------------------------------- void Unlock_F81964 (void) outportb(F81964_INDEX_PORT, F81964_UNLOCK); outportb(F81964_INDEX_PORT, F81964_UNLOCK); //--------------------------------------------------------------------------- void Lock_F81964 (void) outportb(F81964_INDEX_PORT, F81964_LOCK); //--------------------------------------------------------------------------- void Set_F81964_LD( unsigned char LD) Unlock_F81964(); CSB200-822 User Manual...
- Page 81 #define F81964_DATA_PORT (F81964_BASE+1) //--------------------------------------------------------------------------- #define F81964_REG_LD 0x07 //--------------------------------------------------------------------------- #define F81964_UNLOCK 0x87 #define F81964_LOCK 0xAA //--------------------------------------------------------------------------- unsigned int Init_F81964(void); void Set_F81964_LD( unsigned char); void Set_F81964_Reg( unsigned char, unsigned char); unsigned char Get_F81964_Reg( unsigned char); //--------------------------------------------------------------------------- #endif // F81964_H CSB200-822 User Manual...