Informational Messages ���������������������������������������������������� 135 Ec Declaration Of Conformity - Honeywell XNX-AM Series Technical Manual

XNX Universal Transmitter
Informational Messages
Number Description
I001
Unused
I002
Force Relay Mode Started
I003 Force Relay Mode Ended.
I004 Force mA Mode Started
I005 Force mA Mode Ended
I006 Short-Term Inhibit Started
I007
Short-Term Inhibit Ended
I008
Long-Term Inhibit Started
I009
Long-Term Inhibit Ended
I010 mA Output Recalibrated
I011 Bump Test Started
I012 Bump Test Timed Out
I013 Bump Test Completed Concentration < Al1 Peak concentration observed
Bump Test Completed
I014
Al1 < Concentration < Al2
I015
Bump Test Completed. Al2 < Concentration Peak concentration observed
I016
Zero Calibration Successful
I017 Zero Calibration Failed
I018 Calibrate Span Successful 1 of 2
I019 Calibrate Span Successful 2 of 2
I020 Calibrate Span Failed
I021
Calibrate Span Timeout
I022
Password Changed
I023 Performing Soft Reset
I024 Alarms Configured Latching
I025 Alarms Configured Non-Latching
Alarm Relays Configured Normally
I026
Energized
Warnings/Faults
Contents of Data Field
Bitpattern for relays. (E.G. 7.0 ==All)
N/A
Force current. (E.G. 20.0)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Peak concentration observed
N/A
Error code
Percent change in span factor from previous
Absolute span factor
Error code
N/A
1,2 or 3 (access level)
N/A
N/A
N/A
N/A
Number Description
Alarm Relays Configured Normally De-
I027
Energized.
I028 Fieldbus Address Changed
I029
Fieldbus Speed Changed
I030
Sensor Type Changed
I031
Gas Selection Changed
I032 Time For Beam Block Fault Changed
I033 Time For Fault Detection Changed
I034 Level For Low Signal Fault Changed
I035 Invalid Path Length Written
I036
Path Length Changed
I037
mA for Inhibit Changed
I038 mA for Warning Changed
I039 mA for Overrange Changed
I040 mA for Fault Changed
I041 mA for Low Signal Changed
I042 mA for Blocked Beam Changed
I043
Concentration for mA Full Scale Changed
I044
Instrument Id Changed
I045 Measuring Units Changed
Alarm 1 Reconfigured for Increasing
I046
Concentrations
Alarm 1 Reconfigured for Depleting
I047
Concentrations
Alarm 2 Reconfigured for Increasing
I048
Concentrations
Alarm 2 Reconfigured for Depleting
I049
Concentrations
I050 Alarm 1 Value Changed
I051
Alarm 2 Value Changed
I052 Clock Set
135
Contents of Data Field
N/A
New address (e.g. 15)
New speed (e.g. 19200)
iCurrentCalGlobalID
iCurrentCalGlobalID
iBlockFltTime
iOtherFltTime
fLowSignalLevel
fPathLen
fPathLen
f_mA_Flt_Step[0]
f_mA_Flt_Step[1]
f_mA_Flt_Step[2]
f_mA_Flt_Step[3]
f_mA_Flt_Step[4]
f_mA_Flt_Step[5]
fDisplayRange
N/A
iMeasurementUnits
N/A
N/A
N/A
N/A
fAlarmThres[0]
fAlarmThres[1]
N/A