Advertisement
Quick Links
© Panduit Corp. 2009, 2010
CN3
(1) Base Cabinet
(2) Cable Management Finger Kits
(1) Hardware Kit
(2) #12-24 Threaded Equipment Rail Sets
For installation instructions for the CN3 cabinet, please reference instruction sheet CM317C.
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
N
-A
ET
CCESS
INSTRUCTIONS CM385E
Component Guide
CN7018-EXT
CN7018-EXTND*
(2) Top Side Extensions
(2) Top Front/Rear Extensions
(2) Bottom Door Shoe Extensions
(2) Bottom Side Extensions
(2) Split Door Sets
(2) Vertical Side Supports
(4) Lower Horizontal Supports
(1) Hardware Kit
*CN7018-EXTND does not contain doors
Page 1 of 12
Cabinet for Cisco Nexus 7018 Switch
CNAE7018
(1) Inlet Duct Assembly
(1) Exhaust Duct Assembly
(1) Bottom Duct Assembly
(1) Inlet Duct Seal Bracket
(5) Mounting Brackets
(1) Hardware Kit
TOOL LIST
#2 Phillips Screwdriver
#3 Phillips Screwdriver
Needle Nose Pliers
1/8" Allen Key
1/2" Socket Wrench
3/8" Socket Wrench
5/16" Socket Wrench
7/16" Socket Wrench
3/8" Wrench
CNPS7018*
(2) Side Panels
(1) Hardware Kit
*(1) CNPS7018 kit is needed
per cabinet side
Advertisement
Related Manuals for Panduit CN3
Summary of Contents for Panduit CN3
- Page 1 (4) Lower Horizontal Supports (1) Hardware Kit *(1) CNPS7018 kit is needed (1) Hardware Kit per cabinet side *CN7018-EXTND does not contain doors For installation instructions for the CN3 cabinet, please reference instruction sheet CM317C. FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp Page 1 of 12...
- Page 2 CN3 Cabinet Preperation Remove J-Hooks Remove Door Shoe Bumpers and Bushing Remove all (4) J-Hooks from CN3 cabinet by removing Remove (3) door shoe bumpers and (1) door rod bushing from (2) #12-24 screws per J-Hook as shown. each door shoe on the CN3 cabinet as shown.
- Page 3 CISCO NEXUS 7018 SWITCH CRADLE MUST BE mounted so that the shaded area shown below is kept clear to allow for proper fit of all switch ducting to cabinet. See view below for Panduit-suggested cradle position (refer to Cisco for cradle installation instructions).
- Page 4 Duct Assembly Top Flange Universal Ducting Bracket Assembled Exhaust Duct Position Duct Assembly Top Flange Above Top Surface of Switch [7] #12-24 Serrated Hex Head Screws FRONT OF (use 5/16” socket wrench) SWITCH For Technical Support: www.panduit.com/resources/install_maintain.asp Page 4 of 12...
- Page 5 BRACKET AT 1st SET OF PAIRED HOLES FROM BOTTOM OF CABINET POST [1] #12-24 Serrated Hex Head Screw (use 5/16” socket wrench) [4] #12-24 Serrated REAR OF CABINET Hex Head Screws (use 5/16” socket wrench) For Technical Support: www.panduit.com/resources/install_maintain.asp FRONT OF CABINET Page 5 of 12...
- Page 6 Transition Bracket Intake Duct [2] #12-24 Serrated [2] #10-32 Hex Nuts Hex Head Screws (use 3/8” socket wrench) (use 5/16” socket wrench) REAR OF CABINET [4] #10-32 Hex Nuts (use 3/8” socket wrench) For Technical Support: www.panduit.com/resources/install_maintain.asp Page 6 of 12...
- Page 7 Front Extension Remove Center Key Hole Knock-outs 1/4-20 Carriage Bolt See Detail View See Detail View #10 Lockwasher 1/4-20 Serrated Hex Nut (use 7/16” socket wrench) #10-32 Nut (use 3/8” socket wrench) For Technical Support: www.panduit.com/resources/install_maintain.asp Page 7 of 12...
- Page 8 Installation of Bottom Side Extensions Install (2) bottom side extensions as shown. Secure using (2) #12-24 serrated hex head screws on each extension. Assembled Bottom Side Extension #12-24 Serrated Hex Head Screws For Technical Support: www.panduit.com/resources/install_maintain.asp Page 8 of 12...
- Page 9 #10 Lockwashers Lower Horizontal Supports (use 1/8” Allen Key) See Detail View #10-32 Flat Head Screws and #10 Lockwashers (use 1/8” Allen Key) 1/4-20 Hex Head Screw (use 7/16” socket wrench) For Technical Support: www.panduit.com/resources/install_maintain.asp Page 9 of 12...
- Page 10 Unlocked Position Top Spring Loaded Hinge Pin Reposition Horizontal Loosen these Support as Reposition necessary screws Bottom Side Extension as Hinge Pin necessary Locked Position Bottom Spring Loaded Hinge Pin Loosen this screw For Technical Support: www.panduit.com/resources/install_maintain.asp Page 10 of 12...
- Page 11 CN7018, install bottom ganging brackets here (use 5/16” socket wrench) FRONT OF CN7018 CABINET To gang Net-Access cabinet flush with REAR of CN7018, install bottom ganging brackets here For Technical Support: www.panduit.com/resources/install_maintain.asp Page 11 of 12...
- Page 12 5/16” Serrated Bolt BASE OF CABINET GANGING (Front) 1/4” Tapped Hole BASE OF CABINET GANGING (Rear) 1/4” x 2-1/2” Bolt 1/4” x 2-1/2” Bolt For Instructions in Local Languages E-mail: and Technical Support: cs@panduit.com Fax: www.panduit.com/resources/install_maintain.asp (708)444-6448 www.panduit.com Page 12 of 12...