Advertisement
Quick Links
© Panduit Corp. 2008
CN3
(1) Base Cabinet
(2) Cable Management Finger Kits
(1) Hardware Kit
(2) #12-24 Threaded Equipment Rail Sets
For installation instructions for the CN3 cabinet, please reference instruction sheet CM317B.
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
N
-A
ET
CCESS
INSTRUCTIONS CM385
Component Guide
CN7018-EXT
(2) Top Side Extensions
(2) Top Front/Rear Extensions
(2) Bottom Door Shoe Extensions
(2) Bottom Side Extensions
(2) Split Door Sets
(2) Vertical Side Supports
(1) Hardware Kit
Page 1 of 8
Cabinet for Cisco Nexus 7018 Switch
CNAE7018
(1) Inlet Duct Assembly
(1) Exhaust Duct Assembly
(1) Bottom Duct Assembly
(5) Mounting Brackets
(1) Hardware Kit
CNPS7018
(2) Side Panels
(2) Lower Horizontal Supports
Advertisement
Related Manuals for Panduit NET-ACCESS CN3
Summary of Contents for Panduit NET-ACCESS CN3
- Page 1 Cabinet for Cisco Nexus 7018 Switch CCESS INSTRUCTIONS CM385 © Panduit Corp. 2008 Component Guide CNAE7018 CN7018-EXT (2) Top Side Extensions (1) Inlet Duct Assembly (1) Base Cabinet (2) Top Front/Rear Extensions (1) Exhaust Duct Assembly (2) Cable Management Finger Kits...
- Page 2 Align all top extension parts, leaving a minimal gap between side and front/rear parts. Secure side extensions by tightening (4) 5/16” serrated flange lock nuts. Assembled Rear Extension Front Extension See Detail View #10-32 Nut #10 Lockwasher For Technical Support: www.panduit.com/resources/install_maintain.asp Page 2 of 8...
- Page 3 Installation of Bottom Side Extensions Install (2) bottom side extensions as shown. Secure using (2) #12-24 serrated hex head screws on each extension. Assembled Bottom Side Extension #12-24 serrated hex head screws For Technical Support: www.panduit.com/resources/install_maintain.asp Page 3 of 8...
- Page 4 The top flange of duct assembly should be positioned above the top surface of switch. #10-32 Pan Head See Detail View Phillips Screws #10 Lockwashers Universal Ducting Bracket Assembled Exhaust Duct #12-24 serrated hex head screws For Technical Support: www.panduit.com/resources/install_maintain.asp Page 4 of 8...
- Page 5 Extend inlet duct when also using bottom duct Rear Mounting Bracket REAR OF CABINET #10-32 hex nuts and #12-24 serrated #10 lockwashers hex head screws Assembled #12-24 serrated hex head screws For Technical Support: www.panduit.com/resources/install_maintain.asp Page 5 of 8...
- Page 6 Mount (2) vertical side supports using (4) #10-32 nuts per post; (2) at top and (2) at bottom (there are (4) pre-installed press studs in each post). Assembled Vertical Side Supports #10 Lockwashers #10-32 Nuts For Technical Support: www.panduit.com/resources/install_maintain.asp Page 6 of 8...
-
Page 7: Side Panel Installation
Release levers when aligned. Reverse steps to remove side panels. Hinge Pin Unlocked Position Spring Loaded Top Spring Hinge Pin Loaded Hinge Pin Hinge Pin Locked Position Bottom Spring Fixed Hinge Pin Loaded Hinge Pin For Technical Support: www.panduit.com/resources/install_maintain.asp Page 7 of 8... - Page 8 Tighten the (2) hex head screws. See Detail View Loosen these screws Reposition Bottom Side Extension as necessary For Instructions in Local Languages E-mail: and Technical Support: cs@panduit.com Fax: www.panduit.com/resources/install_maintain.asp (708)444-6448 www.panduit.com Page 8 of 8...