Advertisement
Quick Links
© Panduit Corp. 2024
PZWMC9W
PZWMC12*
Location Footprint
INSTALLATION INSTRUCTIONS
A
Footprint with Cabinet Open
25.0"
Cabinet Width
16.0"
Mounting Holes
FOR TECHNICAL SUPPORT www.panduit.com
Wall Mount Cabinet
P
Z
AN
ONE
Part Numbers: PZWMC9W, PZWMC12*, PZWMC18*, PZWMC26*
PZWMC18*
4.5"
Page 1 of 11
Parts Included:
(1) - Extra Door Spacer
(6) - Keys
(1) - Roll of Tak-Ty
(12) - #12-24 Screws
(1) - Removable Top Vent Cover Panel
PZWMC26*
CABINET
DEPTH
25.0"
30.0"
RU
9
12
18
26
0.8"
B
C
Mounting
Holes
V00028CU_06
DIM "A"
45.1"
50.1"
DIM "B" DIM "C"
15.5"
18.5"
20.7"
23.8"
31.2"
34.3"
45.2"
48.3"
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Panduit PANZONE PZWMC9W
Summary of Contents for Panduit PANZONE PZWMC9W
- Page 1 Wall Mount Cabinet Part Numbers: PZWMC9W, PZWMC12*, PZWMC18*, PZWMC26* INSTALLATION INSTRUCTIONS V00028CU_06 © Panduit Corp. 2024 Parts Included: (1) - Extra Door Spacer (6) - Keys (1) - Roll of Tak-Ty (12) - #12-24 Screws (1) - Removable Top Vent Cover Panel...
- Page 2 INSTALLATION INSTRUCTIONS V00028CU_06 © Panduit Corp. 2024 Wall Mount Cabinets can be installed in a hinged right or hinged left application. For your installation, determine which side of the cabinet will hinge. The cabinet is shown hinged left. Mounting surface must have sufficient strength to support the cabinet with payload in both vertical and horizontal loads.
- Page 3 INSTALLATION INSTRUCTIONS V00028CU_06 © Panduit Corp. 2024 Step 3: To adjust the depth of the mounting rail for specific applications, remove the M6 thread forming screws and lockwashers, move the rail to the desired position and re-install mounting hardware. For PZMWCGK Cabinet Jumper Grounding Kit Only...
- Page 4 INSTALLATION INSTRUCTIONS V00028CU_06 © Panduit Corp. 2024 Cable Routing Cable must be routed with an adequate slack loop to prevent cable damage. Route cable to point 1 secure to tie down with a T . Next route cable across the bottom of the enclosure to point 2 secure to tie down with a T .
-
Page 5: Optional Accessories
INSTALLATION INSTRUCTIONS V00028CU_06 © Panduit Corp. 2024 Optional Accessories PZWMC12W (Shown) Cabinet with Window Door PZWMC-CL PZWMC9RR PZWMCFKHF Combination PZWMC12RR PZWCMFKHF-E PZCFK Lock Kit PZWMC18RR PZCFK-E PZWMC26RR Fan Kit Fan Kit Rear Equipment High Flow Rail Kits PZBR4 4” Bend... - Page 6 INSTALLATION INSTRUCTIONS V00028CU_06 © Panduit Corp. 2024 Fan Kits (PZCFK, PZCFK-E, PZWMCFKHF, PZWMCFKHF-E) Fan kits are installed using (4) #10-32 screws and lockwashers provided with kit as shown below. If only one fan kit is used, install the provided blank on the opposite wall using (4) #10-32 screws and lockwashers provided.
- Page 7 INSTALLATION INSTRUCTIONS V00028CU_06 © Panduit Corp. 2024 Horizontal Slack Manager (PZCHSM2) Install tray using (4) #12-24 x 1/2 screws provided at desired Figure 3 RU as shown in figure 3. Refer to recommended layout section for optimal mounting location(s). Screw Mounting Locations Bend Radius Post Installation Bend radius posts can be installed at any rack location using (1) #12-24 x 2.5"...
-
Page 8: Kit Contents
INSTALLATION INSTRUCTIONS V00028CU_06 © Panduit Corp. 2024 Lock Kits (PZWMC-CL) Kit Contents Cam Lock Spacer Cam Lock Spacer Rings Rings • Combination locks (2) • Spacer rings (2) • Cylinder nuts (2) Combination locks Combination locks • Retaining screw (2) - Page 9 INSTALLATION INSTRUCTIONS V00028CU_06 © Panduit Corp. 2024 Installation (continued) Lock Cam (saved) Washer from previous Retaining • Install the remaining parts in the following order: lock) Direction Setting Washer, Cam (saved from previ- Screw ous lock), Flat Washer, Lock Washer, and Retain- ing Screw.
- Page 10 INSTALLATION INSTRUCTIONS V00028CU_06 © Panduit Corp. 2024 Recommended Layout (9 RU) Recommended Layout (12 RU) 2RU of 24 Port Patch Panel 2RU of 24 Port Patch Panel PZCHSM2 1 RU of Blanking Panel 2 RU of Blanking Panel 2RU of 24 Port Patch Panel...
- Page 11 V00028CU_06 INSTALLATION INSTRUCTIONS © Panduit Corp. 2024 Recommended Cable Routing Guide Place patch cord slack around furthest spool as feasible to provide best possible cable management Top View of PZCHSM2 Never cross over center line of horizontal slack manager with cable slack...
Need help?
Do you have a question about the PANZONE PZWMC9W and is the answer not in the manual?
Questions and answers