Table of Contents
Advertisement
© Panduit Corp. 2015
FCE1U
CONTENTS: (#) indicates FCE2U quantity
1 - ENCLOSURE
2 (3) - Tak-Tys, 6" pcs.
2 (3) - ADHESIVE MOUNTS
2 - SLACK SPOOLS
1 (2) - #10-32 x 3/8" SCREW
3 (4) - #10-32 HEX NUTS
WARNING: UNMATED CONNECTORS MAY EMIT INVISIBLE LASER RADIATION. DO NOT LOOK DIRECTLY INTO THE END OF THE
CONNECTOR. DO NOT INSPECT WITH MAGNIFYING DEVICES. MAINTAIN DUST CAPS ON UNMATED CONNECTORS.
CAUTION:
Fiber optic cable is sensitive to excessive pulling, bending, and crushing forces. Consult the manufacturer's cable specification sheet for the
specific cable in use.
Follow TIA/EIA-568-A, 569, 606, and 607 installation guidelines where applicable.
Care should be taken when opening or closing a fully loaded drawer in order to protect the fiber components.
ASSEMBLY VIEW
Fiber Adapter Panels (FAPs):
Up to 4 for FCE1U & FCE1UA
Up to 8 for FCE2U
(sold separately)
Bend radius
control clip
Door assembly
(shown in the
open position)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Opticom QuickNet Rack Mount
Fiber Cassette Enclosures
Part Numbers: FCE1U, FCE1UA, FCE2U
INSTALLATION INSTRUCTIONS
FCE1UA
3 (4) - CABLE ENTRY GROMMETS
4 - #M6 x 1 SCREWS
1 (2) - STRAIN RELIEF BRACKET
4 - CABLE TIES, PLT2S-M0
2 (4) - PLUNGER AND GROMMETS
2 (4) - BEND RADIUS CONTROL CLIPS
Enclosure
Plunger and
grommet
Page 1 of 11
4 - #12-24 x 1/2" SCREWS
1 - CAUTION LABEL
1 - LASER WARNING LABEL
3 - ADHESIVE BEVEL ENTRY CLIPS
Trunk or interconnect
cable entry location
Mounting bracket
Enclosure
sliding drawer
FS006D
FCE2U
Strain relief
bracket
Figure 1
Advertisement
Table of Contents
Related Manuals for Panduit FCE1U
Summary of Contents for Panduit FCE1U
- Page 1 Care should be taken when opening or closing a fully loaded drawer in order to protect the fiber components. ASSEMBLY VIEW Trunk or interconnect Enclosure cable entry location Fiber Adapter Panels (FAPs): Up to 4 for FCE1U & FCE1UA Up to 8 for FCE2U Strain relief (sold separately) bracket Bend radius...
- Page 2 INSTALLATION INSTRUCTIONS FS006D © Panduit Corp. 2015 Preparation and Rack Mounting Determine where the cable will enter the enclosure. Carefully remove the knock-out so as not to damage the surrounding sheet metal. DO NOT Install grommet at this stage. Grommet will be installed after the enclosure is mounted to the rack.
- Page 3 INSTALLATION INSTRUCTIONS FS006D © Panduit Corp. 2015 Grommet Cutting Diagram After the enclosure is mounted to the rack, determine the size of the innerduct that will be used to bring the cable into the enclosure. Prepare grommet(s) according to the proper cutting diagram to the left.
- Page 4 INSTALLATION INSTRUCTIONS FS006D © Panduit Corp. 2015 QuickNet Cassette Installation (cassettes not included) Depress spring latch and pull sliding tray out to the extended position. Spring latch Figure 7 Insert QuickNet Pre-Terminated Fiber Optic Cassettes into the enclosure as shown. Once mounted, fully seat NyLatch fasteners to secure the cassettes.
- Page 5 INSTALLATION INSTRUCTIONS FS006D © Panduit Corp. 2015 Tak-Ty cables to fence Grommet Fixed Route fiber through grommet to fiber cassettes as Tak-Ty shown. Leave enough slack so when the drawer is fully extended the cables are not put under tension.
- Page 6 INSTALLATION INSTRUCTIONS FS006D © Panduit Corp. 2015 Field Termination or Pre-Terminated Trunk Installation Fiber Adapter Panels (FAPs): Up to 4 for FEC1U & FCE1UA Slack spools Up to 8 for FCE2U Place slack spools over #10-32 studs on sliding tray. Secure with #10-32 hex nuts and/or adhesive mounts (make sure to punch hole into adhesive mounts).
- Page 7 INSTALLATION INSTRUCTIONS FS006D © Panduit Corp. 2015 Tak-Ty cables to Route fiber through grommet as shown. Use fence as needed. Grommet enough cable length to ensure one complete loop (approx. 52" [1.32m]) of individual fibers around slack spools. Leave enough jacketed slack so when the drawer is fully extended the “A”...
- Page 8 #10-32 hex nuts. Remaining FOSMs are stacked on top of each other and snap in place. If 4 FOSMs are to be installed in the FCE1U or FCE1UA, side latches on top module must be broken off to close the enclosure drawer.
- Page 9 INSTALLATION INSTRUCTIONS FS006D © Panduit Corp. 2015 Tak-Ty cables Grommet to fence Route fiber through grommet as shown. Use “A” enough cable length to ensure one complete loop (approx. 45" [1.15m]) of individual fibers around FOSM slack spools. Fixed Tak-Ty...
- Page 10 INSTALLATION INSTRUCTIONS FS006D © Panduit Corp. 2015 Patch Cord Bend Radius Control Clip Installation Plunger and grommet Bend radius control clips Plunger and grommet Figure 10 Slide bend radius control clip over sliding tray Bend radius flange as shown. Push plunger/grommets...
- Page 11 INSTALLATION INSTRUCTIONS FS006D © Panduit Corp. 2015 Door Re-Attachment Re-install front door and rear door assemblies, if removed during fiber installation. Attach Laser Warning Label and Caution Label where they are clearly visible. Figure 12 E-mail: For Instructions in Local Languages techsupport@panduit.com...