Keysight Technologies N9030B Installation Note
  1. Manuals
  2. Brands
  3. Keysight Technologies Manuals
  4. Measuring Instruments
  5. N9030B
  6. Installation note
Keysight Technologies N9030B Installation Note

Keysight Technologies N9030B Installation Note

Pxa signal analyzer
Hide thumbs Also See for N9030B:
Table of Contents

Advertisement

Quick Links

Download this manual
Keysight Technologies
N9030B PXA Signal Analyzer
Option HL2 Microwave Preselector Bypass
(MPB) and Low Noise Path (LNP)
for mm-Wave Instruments
Installation Note

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the N9030B and is the answer not in the manual?

Questions and answers

Related Manuals for Keysight Technologies N9030B

Summary of Contents for Keysight Technologies N9030B

  • Page 1 Keysight Technologies N9030B PXA Signal Analyzer Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) for mm-Wave Instruments Installation Note...
  • Page 2 The information contained in this document is subject to change without notice. Keysight Technologies makes no warranty of any kind with regard to this material, including but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
  • Page 3 Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit Products Affected: N9030B PXA, Option 544 and 550 Serial Numbers: To Be Performed By: (X) Keysight Service Center...

  • Page 4: Installation Kit Parts List

    Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit Installation Kit Parts List Quantity Description Keysight Part Number Installation Note This note Option Upgrade Entitlement Certificate 5964-5178 Transfer Switch (SW4) 87222-60031 Transfer Switch, (top switch) (SW3) 87222-60029 Bracket, Switch N9020-00021...

  • Page 5: Tools Required

    Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit Tools Required — T-8 TORX Driver — T-10 TORX Driver — T-20 TORX Driver — 5/16-inch torque wrench — Keysight Calibration and Adjustment Software, N7814A, revision E.16.00 or greater —...

  • Page 6: Installation Procedure

    Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit Installation Procedure If the instrument is placed on its face during any of the following procedures, be sure to use a soft surface or soft cloth to avoid damage to the front panel, keys, or input connector. Make sure any adapters on the front panel are removed.
  • Page 7 Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit 2. Locate the YTF (4) and remove W56 from between the YTF and the Low Band Switch Assembly (3), and remove W57 between the YTF and the Front End Assembly at J9. These cables will not be reused.
  • Page 8 Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit 3. Refer to Figure 3. Locate the switch wire harness (1) and the empty connector body 1252-1873 (2). Plug the empty connector body into the switch wire harness connector that has the orange, black, green wires.
  • Page 9 Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit 5. Refer to Figure 4. Position the switch/bracket assembly into the frame. Route W7 ribbon cable between the switches. Notice the position of the other ribbon cable W55 and wire harness W12.
  • Page 10 Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit Installing Semi-Rigid Cables 1. Refer to Figure 5. Locate W52 N9020-20125 (1), and W54 N9020-20127 (2), in the kit and install them as shown. Torque cables to 10 inch-lbs. Figure 5 W52 and W54 Cable Installation Installation Note N9030-90084...
  • Page 11 Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit 2. Refer to Figure 6. Locate W60 N9020-20128 (1) in the kit and install it as shown. Locate W61 N9020-20129 (2), and install it as shown. Locate W59 N9020-20151 (3) and install it.
  • Page 12 Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit 3. Refer to Figure 7. Locate W51 N9020-20171 (1) in the kit and install one end to top switch port 1 and the other end to Attenuator B output. Torque cables to 10 inch-lbs. Figure 7 W51 Cable Installation Installation Note N9030-90084...
  • Page 13 Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit Connect the Ribbon and Wire Harness Cables to the Front End Control Assembly 1. Refer to Figure 8. Determine where ribbon cables W55 and W7 attach, and also where wire harness W12 attaches.

  • Page 14: License Installation Procedure Over Usb

    Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit License Installation Procedure over USB In any correspondence or telephone conversation, refer to the product by its model number and full serial number. With this information, the Keysight representative can determine the warranty status of your unit.

  • Page 15: Verify The Installation

    Option HL2 Microwave Preselector Bypass (MPB) and Low Noise Path (LNP) Retrofit Kit Figure 10 Successful License Installation Verify the Installation 1. Cycle the power on the signal analyzer. 2. Press System, Show System to display a list of installed options. 3.
  • Page 16 For assistance, get in touch with your nearest Keysight Technologies Sales and Service Office. To find your local Keysight office access the following URL, or if in the United States, call the following telephone number: http://www.keysight.com/find/assist...
  • Page 17 This information is subject to change without notice. © Keysight Technologies 2016 Edition 1, February 2016 N9030-90084 www.keysight.com...

Table of Contents