Page 2
Trademarks BOSER is a registered trademark of BOSER Technology Co., Ltd. Intel is a registered trademark of Intel Corporation. Award is a registered trademark of Award Software, Inc.
...................... 6 PECIFICATIONS 1.2 D ..................... 7 ELIVERY ACKAGE HARDWARE INSTALLATION...................9 2.1 C ............... 9 AUTION OF TATIC LECTRICITY 2.2 HS-3200/4M' ..................10 AYOUT 2.3 Q ................ 11 UICK ISTING OF ONNECTORS 2.4 Q ................12 UICK ISTING OF UMPERS 2.5 J...
Page 4
AMI BIOS SETUP .......................35 4.1 M ......................36 4.2 S CMOS S ................. 37 TANDARD ETUP 4.3 A CMOS S ................. 38 DVANCED ETUP 4.4 A ................40 DVANCED HIPSET ETUP...
It allows up to 64 MB RAM and can run at 40 MHz with a single-sided memory module. The HS-3200/4M provides 4MB system RAM on board. The HS-3200/4M can support either a LCD Panel or VGA equipped monitor, ®...
1.1 Specifications The HS-3200/4M Industrial Single Board provides the following specification: CPU : 386SX-40 (Embedded in M6117 chipset). Bus interface : ISA bus. ® Chipset : ALi M6117 Data bus : 16-bit Processing ability : 32-bit ® Flat panel / CRT SVGA controller : Intel 65545 Chipset with 1MB memory.
Max. power requirement : +5V @1.8A. Operating temperature : 0~55?C Dimensi on : 7.3”(L) x 4.8”(W) (185mm x 122mm) 1.2 Delivery Package The HS-3200/4M package includes the following items: HS-3200/4M Single Board Computer Printer port Flat Cable IDE port Flat Cable...
Page 8
If any of these items are missing or damaged please contact your dealer. Keep all the shipping materials and the packing box in case of you want to ship or store the product in feature.
Chapter-2 Hardware Installation This chapter describes how to install the HS-3200/4M. At first, please follow the unpacking information. The jumpers and switches setting, watchdog timer setting, and the DiskOnChip? address selection, are also included. 2.1 Caution of Static Electricity Your HS-3200/4M Industrial Single Board contains very sensitive electronic components that can be easily damaged by the static electricity.
2.5Jumper Description This board’s default jumpers are present at the factory. If you want to change the HS-3200/4M’s configuration, please follow the instructions. A jumper switch is closed (sometimes referred to as shorted with a plastic cap inserted over two pins of the jumper). A jumper is open with a plastic cap inserted over one or no pin(s) of the jumper.
Each socket will accommodate a 72-pin DRAM module - 256K x 36 bit (1MB), 1M x 36 bit (4MB) or 4M x 36 bit (16MB). The memory access time should be 70ns or less. The HS-3200/4M have 1 SIMM socket and 4 Mbytes on board.
220 sec *) : default setting When the power of the HS-3200/4M is turned on, the Watch-Dog timer is disabled. The watch-dog timer can be enabled by reading the Watch-dog timer enable/refresh control port (443H) and disabled by reading the Watch-dog timer disable control port (43H).
Page 16
443H I/O Read Enable/refresh the Watch -Dog Timer. 043H I/O Read Disable the Watch-Dog Timer. The following programs are the examples of how to enable, disable and refresh the Watch-Dog timer: WDT_EN_RF 0443H WDT_DIS 0043H WT_Enable PUSH ;save AX, DX PUSH DX,WDT_EN_RF ;enable the watch-dog timer...
2.8VGA Controller ® The HS-3200/4M is equipped with a VGA controller. It uses an Intel 65545 ISA-bus VGA controller which supports up to 1280x1024 resolution. It also provide the LCD Panel I/F to support panels. Highly integrated design (Flat Panel/CRT VGA) Bus : ISA bus 16-bit ®...
JP11 determines the memory address of the DiskOnChip? .If you have another add-on card in the system with the same memory, neither the HS-3200/4M nor the add-on card will function normally. Please change the memory address. JP11 : DiskOnChip? Address PIN NO.
2.11Jumper Setting and Selection of RS-232/422/485 The HS-3200/4M provide you to select the board with CN16 RS-232 workable or CN12 RS-422/485. Please refer to the following jumpers setting for detail. JP1 : RS-232 COM 4 Disable Select Selection OPEN RS-232...
Chapter-3 Connection This chapter describes how to connect the peripherals, switches and indicators to the HS-3200/4M board. 3.1 Floppy Disk Drive Connector HS-3200/4M board is equipped with a 34-pin daisy-chain driver connector cable. CN7 : FDC CONNECTOR PIN NO. DESCRIPTION PIN NO.
3.2 PCI E-IDE Drive Connector The HS-3200/4M has on board IDE interface. It can be connected up to two IDE (Integrated Device Electronics) hard disk drives. CN10 : IDE Interface Connector DESCRIPTION PIN NO. DESCRIPTION RESET GROUND DATA 7 DATA 8...
3.3 Parallel Port The HS-3200/4M includes an on board parallel port which accesses through a 26-pin flat-cable connector CN2. CN2 : Parallel Port Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION STROBE DATA 0 DATA 1 DATA 2 DATA 3 DATA 4...
3.5External Switches and Indicators There are many external switches and indicators to monitor and control your CPU board. CN4 : Keylock PIN NO. DESCRIPTION POWER LED ANODE GROUND KEYLOCK GROUND CN3 : Reset Button PIN NO. DESCRIPTION EXTERNAL RESET GROUND CN6 : IDE LED connector PIN NO.
GROUND 3.7PS/2 6-Pin Mini Din Mouse Connector The HS-3200/4M has a PS/2 mouse on board which uses IRQ12. If you do not use the PS/2 mouse and wish to assign IRQ12 for other purposes, you may change JP8 to disconnect PS/2 interrupt from IRQ12.
HSYNC VSYNC 3.9PC/104 Connection Bus The HS-3200/4M’s PC/104 expansion bus can let you connect any kinds of the PC/104 modules. The PC/104 bus has already become the industrial embedded PC standard bus, so you can easily install over thousands of PC/104 modules from hundreds of venders in the world.
Page 28
CN8&CN9 : PC/104 Expansion Bus (CN8 = 64-pin female connector; CN9 = 40-pin female connector.) Row A Row B Row D Row C IOCHECK* 33 0V 1 0V 21 0V 34 RESETDRV 2 MEMCS16* 22 SBHE* 35 +5V 3 IOSC16* 23 LA23 36 IRQ9 4 IRQ10...
3.11External Power Connector The HS-3200/4M provides one 4-pin DC-Power connector as following CN1 pin information. CN1 : 4-Pin Power Connector PIN NO. DESCRIPTION +12V 3.12 Fast Ethernet Connector The Fast Ethernet controller provides with 10 Based operation, please connect the network connection by plugging one end of the cable into the to CN13 Connector.
Chapter-4 AMI BIOS Setup The HS-3200/4M uses the AMI BIOS for the system configuration. The AMI BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options which could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features.
4.1 Main Menu Once you enter the AMI BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter>...
4.2 Standard CMOS Setup The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for this setup.When the IDE hard disk drive you are using is larger than 528MB, please set the HDD mode to LBA mode.
4.3 Advanced CMOS Setup This advanced setup is designed for the customers to achieve the highest performance of the HS-3200/4M board. As for normal operations, customers don t have to change any default settings. The default setting is pre-set for most reliable operations.
Page 39
Note: The default Flat Panel Display types currently are: Default BIOS Panel Types No Resolution Data Panel Type 640x480 12bit Color TFT NL6448AC30-10 (NEC) 640x480 18bit Color TFT NL6448AC33-18 (NEC) 640x480 18bit Color TFT LQ10D41(SHARP) 800x600 18bit Color TFT NL8060AC26-11(NEC) 640x480 16 bit Dual-Scan Color STN LM64C08P(SHARP)
4.4 Advanced Chipset Setup This setup functions are mostly working for the Chipset (ALI M6117B). These options are used to change the Chipset’s registers. Please carefully change any default settings, otherwise the system could be unstable. AMIBIOS SETUP – ADVANCED CHIPSET SETUP (C)1996 American Megatrends , Inc.