Nordson Encore Installation, Troubleshooting, Repair
  1. Manuals
  2. Brands
  3. Nordson Manuals
  4. Controller
  5. Encore
  6. Installation, troubleshooting, repair

Nordson Encore Installation, Troubleshooting, Repair

Engage system controller
Hide thumbs Also See for Encore:
Table of Contents

Advertisement

Quick Links

Download this manual
r
Encore
Engage System Controller
Installation, Troubleshooting, Repair
Customer Product Manual
Part 1618871-01
Issued 4/20
For parts and technical support, call the Industrial Coating
Systems Customer Support Center at (800) 433-9319 or
contact your local Nordson representative.
This document is subject to change without notice.
Check http://emanuals.nordson.com for the latest version.
NORDSON CORPORATION • AMHERST, OHIO • USA

Advertisement

Table of Contents
loading

Related Manuals for Nordson Encore

Summary of Contents for Nordson Encore

  • Page 1 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative. This document is subject to change without notice. Check http://emanuals.nordson.com for the latest version. NORDSON CORPORATION • AMHERST, OHIO • USA...
  • Page 2 Contact Us Notice This is a Nordson Corporation publication which is protected by copyright. Nordson Corporation welcomes requests for information, comments, and Original copyright date 2020. No part of this document may be inquiries about its products. General information about Nordson can be...
  • Page 3 Change Record Change Record Revision Date Change 4/20 New Release. Part 1618871−01 E 2020 Nordson Corporation...
  • Page 4 Change Record Part 1618871−01 E 2020 Nordson Corporation...

  • Page 5: Table Of Contents

    ....2-11 Approved Program and User Data Cards/USB ... . 2-12 Part 1618871−01 E 2020 Nordson Corporation...
  • Page 6 ........5-10 Part 1618871−01 E 2020 Nordson Corporation...
  • Page 7 ..........Encore Engage Controllers .
  • Page 8 Table of Contents Part 1618871−01 E 2020 Nordson Corporation...

  • Page 9: Safety

    Regulations and Approvals Make sure all equipment is rated and approved for the environment in which it is used. Any approvals obtained for Nordson equipment will be voided if instructions for installation, operation, and service are not followed. All phases of equipment installation must comply with all federal, state, and local codes.

  • Page 10: Personal Safety

    Clean, maintain, test, and repair equipment according to the instructions in your equipment documentation. Use only replacement parts that are designed for use with original equipment. Contact your Nordson representative for parts information and advice. Part 1618871−01 E 2020 Nordson Corporation...

  • Page 11: Grounding

    Disconnect and lock out electrical power. Close pneumatic shutoff valves and relieve pressures. Identify the reason for the malfunction and correct it before restarting the equipment. Disposal Dispose of equipment and materials used in operation and servicing according to local codes. Part 1618871−01 E 2020 Nordson Corporation...

  • Page 12: Safety Labels

    Safety Safety Labels Table 1-1 contains the text of the safety labels on the Encore Engage main system controller, auxiliary cabinet, and remote controller. The safety labels are provided to help operate and maintain the controllers safely. See Figure 1-1 for the location of the safety labels.

  • Page 13: System Overview

    NOTE: The system also requires external part ID sensors such as photoeyes or scanners for part identification and zone detection. See Figure 2-1. The following Encore Engage controllers are available: Encore Engage Main System Controller − Includes touchscreen controls and supports 4−16 powder spray guns Encore Engage System Controller with Remote Interface Controller −...

  • Page 14: Console And System Hardware And Software

    E-stop. An accessory pedestal is also available. The remote controller houses the touchscreen interface, while all other hardware stays in the main controller cabinet. Up to three touch screen displays can be used per a main controller. Part 1618871−01 E 2020 Nordson Corporation...
  • Page 15 6. Gun cable connections 10. Gateway 3. Power switch 7. Dual spray gun cards, card cage, 11. Relay board and backplane 4. Interlock keyswitch 12. 24 Vdc power supply 8. Single +24 V power supply Part 1618871−01 E 2020 Nordson Corporation...

  • Page 16: Touchscreen Interface

    Use the Bypass position to set up and test spray gun settings. In the Lockout position, the spray guns cannot be triggered and the in/out positioners and reciprocators cannot be moved. Use this position when working inside the booth. Part 1618871−01 E 2020 Nordson Corporation...

  • Page 17: Dc Power Supplies

    Dual Spray Gun Cards Each dual spray gun card in the card cage provides electrostatic controls for two Encore automatic powder spray guns. The cards provide a 0−19 Vac (peak) signal to drive the electrostatic power supplies inside the Encore spray guns.

  • Page 18: Internal And External Networks

    For additional operation information, refer to the Encore Enhance Powder Spray Controller manual. VT systems − use Encore LT manual controller. Refer to the Encore LT Manual Powder Spray Systems manual for installation, operation, and repair information.

  • Page 19: Specifications

    Maximum Water Vapor in Air Supply: 0.48 grains/ft Moist or contaminated air can cause the pumps to malfunction; the powder to cake in the reclaim system, or cause clogging in the feed tubing or spray gun powder paths. Part 1618871−01 E 2020 Nordson Corporation...

  • Page 20: Special Conditions Of Use

    System Overview Special Conditions of Use 1. The Encore Engage Control Consoles and Remote Display are only for use in non-explosive atmospheres. 2. The Encore Engage Control Consoles and Remote Display shall be used with the manufactures applicators that are certified under...
  • Page 21 System Overview Figure 2-5 Label for CE ATEX Approval (On Remote Display) Figure 2-6 Label for FM Approval (On Main and Auxiliary Cabinets and Remote Display) Part 1618871−01 E 2020 Nordson Corporation...

  • Page 22: Main And Auxiliary Cabinet Dimensions

    (24 in.) 1807.5 mm (71 in.) 392 mm (15 in.) 196 mm 10.0 (8 in.) 550 mm (22 in.) R616 DOOR OPENING 10019246 Figure 2-7 Main and Auxiliary Cabinet Dimensions (shown with main cabinet) Part 1618871−01 E 2020 Nordson Corporation...

  • Page 23: Remote Controller Touchscreen Interface

    Remote Controller Touchscreen Interface 704 mm (28 in.) 564 mm (22 in.) 414 mm (16 in.) 256 mm (10 in.) 287 mm (11 in.) 10019168 Figure 2-8 Remote Controller Touchscreen Interface Dimensions (shown with optional E-stop extention) Part 1618871−01 E 2020 Nordson Corporation...

  • Page 24: Approved Program And User Data Cards/Usb

    Approved Program and User Data Cards/USB Only Nordson provided program and user data cards are approved for use with Encore Engage system controllers. The following are a list of program and data cards/USB and where they are located in the system.

  • Page 25: Installation

    Introduction Encore Engage systems are configured for each customer’s application and requirements. The equipment supplied with the system varies depending on the type of installation (new, upgrade, or retrofit) and the equipment furnished by the customer.

  • Page 26: System Connections

    NOTE: If system has auxiliary controller, MGI connection should be done at P4 location on auxiliary controller. If only using a main controller, MGI connection should be done at P4 location on main controller. Figure 3-1 Typical System Interconnect Cable Connections Part 1618871−01 E 2020 Nordson Corporation...

  • Page 27: Interconnect Cables

    Air Conditioner Power ⅞-in. mini E-stop 4 Conductor M12 Enet 3 (Remote Screen) M12 D Coded Female E-net WAN (Customer Data) M12 D Coded Female E-net Interlock/Alarm (Optional) 1.25 in. mini Encoder 4 Conductor M12 Part 1618871−01 E 2020 Nordson Corporation...
  • Page 28 Valve 1 White Valve 2 Brown Valve 3 Green Valve 4 Yellow Valve 5 Gray Valve 6 Pink Valve 7 Blue Valve 8 Valve 9 Orange Blue LED +24 V Black +24 V Violet Part 1618871−01 E 2020 Nordson Corporation...

  • Page 29: Electrical Connections

    Î Î Î Î Î Î Î Î Remote AC Power Î Î Î Î Î Î Î Î Î (P3) Î Î Î Î Î Figure 3-2 Rear Panel of Cabinet (Cover Removed) Part 1618871−01 E 2020 Nordson Corporation...

  • Page 30: Pneumatic Connections

    Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Figure 3-3 Console Rear Panel (Cover Removed) Part 1618871−01 E 2020 Nordson Corporation...

  • Page 31: Can Network Connections And Settings

    NOTE: Terminating resistors must be installed for dust tight connections. Field Connections Terminations Backplane Auxiliary Manual Manual Flow Flow Flow Flow Flow Flow Backplane Main Flow Flow Flow Flow Flow Flow Flow Flow Figure 3-4 CAN Network Cable Connections Part 1618871−01 E 2020 Nordson Corporation...

  • Page 32: Terminations

    16 Automatic Spray Guns (main cabinet only) Flow Module 1 (see JP1 − See Figure 3-5) 12 Automatic Spray Guns and 4 Manual Spray Guns (includes main only) After MGI 4 10017279/10018617 Figure 3-5 iFlow Board Part 1618871−01 E 2020 Nordson Corporation...

  • Page 33: Can Address And Termination Settings

    Manual spray gun controllers are shipped with their CAN termination switch set to OFF. For each manual spray gun controller network, terminate using external plug. NOTE: Up to four manual spray guns can be add in a system. Part 1618871−01 E 2020 Nordson Corporation...

  • Page 34: Manual Spray Gun Controller First-Time Startup

    3-10 Installation Manual Spray Gun Controller First-Time Startup NOTE: Refer to the Encore Enhance Powder Spray Controller manual for operation information for the manual gun controller. The manual spray gun controller addresses are set through software. Each controller must have a unique address, along with updating other specific controller functions for basic operation.

  • Page 35: Relay Board

    AUX Backplane Lockout − (P2−3) No Connection Alarm Input +24 (P2−5) Encoder Alarm Input Sig (P2−6) No Connection No Connection Gun Power OK No Connection No Connection Lockout Signal No Connection No Connection No Connection Part 1618871−01 E 2020 Nordson Corporation...

  • Page 36: Relay Board Leds

    Conveyor run signal present, or keyswitch is in bypass mode. Conyeyor run signal not present. Check signal. Lockout Keyswitch is in ready position or bypass. In lockout mode. Alarm No faults. Normal system operation. Indicates fault. Part 1618871−01 E 2020 Nordson Corporation...
  • Page 37 LED3 +12 VDC POWER LED4 +24 VDC POWER ALARM LED5 CONVEYOR LED7 LED6 LOCKOUT 1 2 3 4 5 6 7 8 9 10 1112 13 1415 16 17 18 Figure 3-7 Relay Board Part 1618871−01 E 2020 Nordson Corporation...

  • Page 38: Power Connections

    Blue Interlocked AC common Green Ground Auxiliary Console Power Cable Connections Wire Color Connection Black Interlocked AC (same as main console Red connection) White Interlocked AC common (same as main console Blue connection) Green Part 1618871−01 E 2020 Nordson Corporation...

  • Page 39: Grounding

    Electrostatic discharges occur at very high frequencies, around 100 MHz. An ordinary ground conductor does not conduct such high frequencies well enough to prevent damage to electronic components. Special flat-braided cables are provided with Nordson powder coating equipment to protect against ESD. Part 1618871−01...

  • Page 40: Spray Gun Current Path

    (spray gun driver board and power supply). Spray Gun Current Path Ions Engage Ground Braid Figure 3-8 Electrostatic Current Path Part 1618871−01 E 2020 Nordson Corporation...

  • Page 41: Esd Ground Procedures And Equipment

    ESD Grounding Procedures and Equipment Always use the special flat-braided copper ESD ground cables furnished with all Nordson spray gun controllers to ground them. The ESD ground cables should always be attached to the booth base, not to a panel, enclosure, or other component bolted to the base.

  • Page 42: Spray Gun Cable Connections

    Refer to the Parts section for seal and jumper part numbers. Receptacle #8 Bulkhead Harnesses Seal Jumper Install in #8 Card Receptacle Spray Gun Card Figure 3-10 Seal and Jumper Installation − Example Showing 8-Spray Gun System Using Seven Spray Guns Part 1618871−01 E 2020 Nordson Corporation...

  • Page 43: System Upgrades

    3-19 Installation System Upgrades Certain upgrades require updates to the spray gun control card and iFlow module firmware. These upgrades should only be done by a Nordson representative. Part 1618871−01 E 2020 Nordson Corporation...
  • Page 44 3-20 Installation Part 1618871−01 E 2020 Nordson Corporation...

  • Page 45: Troubleshooting

    NOTE: If the troubleshooting procedures in this section do not solve your problem, contact the Nordson Industrial Coating Systems Customer Support Center at (800) 433−9319 or your local Nordson representative. Part 1618871−01...

  • Page 46: Spray Gun Card Leds

    Check gun to part distance. maximum limit DS5: Yellow Normal: OFF Check the part grounding for GUN B Current open circuit is less than 1 MΩ. Fault: ON Limit Check high voltage arcing. Part 1618871−01 E 2020 Nordson Corporation...
  • Page 47 6. DS4: GUN A current limit processor) (yellow LED) 2. DS3: Communication (green LED) 5. DS5: GUN B current limit 7. SW1 (2 position DIP switch 3. DS2: Fault (red LED) (yellow LED) for future use) Part 1618871−01 E 2020 Nordson Corporation...

  • Page 48: Air Flow Re-Zero Procedure

    8. Remove the tube plugs from the output ports. 9. On the Engage screen, check each spray gun control screen that was previously indicating air flow when the spray gun was off. No air flow should be indicated. Part 1618871−01 E 2020 Nordson Corporation...
  • Page 49 Troubleshooting Figure 4-2 Dual Pump Control Board Part 1618871−01 E 2020 Nordson Corporation...

  • Page 50: Backplane

    Check +24 V on P4 (+24 V LED ON). Fault: OFF Check fuse F2. Check jumpers J11 and J14 are in place. Remove all gun cards. If +5 V LED turns ON, replace one card at a time. Part 1618871−01 E 2020 Nordson Corporation...
  • Page 51 Troubleshooting −12V +12V +24V 10017280 Figure 4-3 Location of Backplane LEDs Part 1618871−01 E 2020 Nordson Corporation...

  • Page 52: Power Supplies

    Remove relay board power J7−5. If DC OK LED turns ON, check relay board. All loads removed. If DC OK LED remains OFF, replace PS2. Return all loads to circuit except the faulted load and check if DC OK LED turns ON. Part 1618871−01 E 2020 Nordson Corporation...
  • Page 53 Troubleshooting 600 W 24 Vdc Power Supply 120 W 24 Vdc Power Supply DC OK AC OK DC OK 1615937/1609757 Figure 4-4 Location of LEDs on Power Supplies Part 1618871−01 E 2020 Nordson Corporation...

  • Page 54: Flow Node

    Check for PLC fault. Check flow node cabling. Check manual gun connections P4. Fault Normal: OFF Check Alerts screen through Engage controller touchscreen for fault codes. Fault: ON High flow fault. Low flow fault. Part 1618871−01 E 2020 Nordson Corporation...
  • Page 55 4-11 Troubleshooting LED1 LED2 10017279/10018617 Figure 4-5 Location of LEDs on Flow Node Part 1618871−01 E 2020 Nordson Corporation...

  • Page 56: Relay Board

    Check keyswitch wiring. Check keyswitch contacts are assembled correctly. LED7 Alarm Normal: ON Check voltage on J7−15 and J7−16. Should be +24 V when system is OK. Fault: OFF Clear faults on Engage controller touchscreen. Part 1618871−01 E 2020 Nordson Corporation...
  • Page 57 4-13 Troubleshooting 10012054 Figure 4-6 Location of LEDs on Relay Board Part 1618871−01 E 2020 Nordson Corporation...

  • Page 58: Plc

    Program error Flashing Application is stopping No micro SD card found Replace Micro SD card. Micro SD card found No USB host found USB host inserted Communication channel opened RS485 Flashing BUS activity Continued... Part 1618871−01 E 2020 Nordson Corporation...
  • Page 59 ETH2 check for remote HMI connection P2. ETH0-2 Check remote HMI power P3. Check remote HMI IP address. Active connection found Active connection and data is Flashing being received or sent Ethernet communication/link status Ethernet Activity Continued... Part 1618871−01 E 2020 Nordson Corporation...
  • Page 60 Check for 24 V on X6. No power on X6 Check PS2. +24 V found at X6 Check for 24 V on UL. No power supply UL at Check PS2. Q1-Q4 +24 V found at UL Part 1618871−01 E 2020 Nordson Corporation...
  • Page 61 4-17 Troubleshooting ETH2 RS485 ETH1 CAN1 ETH0 CAN2 24 VDC Ethernet Activity 1618666 Figure 4-7 PLC LED Locations Part 1618871−01 E 2020 Nordson Corporation...

  • Page 62: Ewon

    ON = Link OK Blinking = Ethernet Traffic Fault: OFF (Rectangle) Normal: ON Check PLC power. Green=LAN Fault: Green OFF Check PLC configuration. Orange=WAN (Square) Normal: Green ON = Link OK Blinking = Ethernet Traffic Fault: OFF Part 1618871−01 E 2020 Nordson Corporation...
  • Page 63 Fault: Green OFF Orange=WAN Green Normal: ON = Link OK Blinking = Ethernet Traffic Fault: OFF LED Panel Ethernet Ports Main Connector Card Slot Reset Button − BI1 1618667 Figure 4-8 eWON LEDs and Components Part 1618871−01 E 2020 Nordson Corporation...
  • Page 64 4-20 Troubleshooting Part 1618871−01 E 2020 Nordson Corporation...

  • Page 65: Repair

    Failure to maintain the dust-tight integrity of the enclosures could invalidate agency approvals and create a hazardous condition. Part 1618871−01 E 2020 Nordson Corporation...

  • Page 66: Spray Gun Control Card Removal/Installation

    NOTE: Cards are installed in the card cage from left to right. Spray guns are numbered from left to right and bottom to top. Part 1618871−01 E 2020 Nordson Corporation...

  • Page 67: Replacing A Card

    11 13 15 Figure 5-9 Spray Gun Control Card Replacement 1. Card cage (slot 1) 3. Spray gun 2 connector 5. Locking tab 2. Gun control card 4. Spray gun 1 connector 6. Backplane Part 1618871−01 E 2020 Nordson Corporation...

  • Page 68: Plc

    Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î 10019116 Figure 5-10 PLC Replacment Part 1618871−01 E 2020 Nordson Corporation...

  • Page 69: Touchscreen Replacement

    3. Disconnect the ground connection (2). 4. Disconnect Ethernet (3) and power harness connection (4). Back View Bottom View 1618656 Figure 5-11 Touchscreen IP Label and Connections 1. IPS label 3. Ethernet 4. Power harness 2. Grounding connection Part 1618871−01 E 2020 Nordson Corporation...
  • Page 70 9. Reconnect ground, Ethernet, and power harness connections. 10. Mark the matching IP address noted earlier on the IP label (shown in Figure 5-11) of the new touchscreen before closing cabinet or remote display. 11. Complete software update using USB. Part 1618871−01 E 2020 Nordson Corporation...
  • Page 71 Repair Remote Display Cabinet Door Figure 5-12 Replacing Touchscreen 5. Touch screen 6. Allen screw 7. Bracket Part 1618871−01 E 2020 Nordson Corporation...

  • Page 72: Iflow Module Repair

    9. Install the coil over the valve stem, with the coil wiring pointing toward the circuit board. Secure the coil with the nut. 10. Connect the coil wiring to the circuit board. Part 1618871−01 E 2020 Nordson Corporation...
  • Page 73 Repair Proportional Valve Cleaning Valve Body − Top Valve Body − Bottom Figure 5-13 iFlow Module Cleaning and Repair Part 1618871−01 E 2020 Nordson Corporation...

  • Page 74: Proportional Valve Replacement

    NOTE: If the seals (4) remain in the manifold port, remove them. 2. Check for filter contamination. If filters (5) are discolored, replace filters using service kit 1604436. Replacement instructions are included with kit. Part 1618871−01 E 2020 Nordson Corporation...

  • Page 75: Parts

    Section 6 Parts Introduction To order parts, call the Nordson Industrial Coating Systems Customer Support Center at (800) 433 contact or your local Nordson representative. Encore Engage Controllers See Figure 6-1 and the following parts list. Main Controller Main Controller...

  • Page 76: Remote Displays

    Remote Displays See Figure 6-2 and the following parts list. Remote Display Remote Display Pedestal for with E-stop Remote Display Figure 6-2 Encore Engage Remote Displays Part Description Note 1618033 KIT, remote display 1618034 KIT, remote display with E-stop 1618035 KIT, pedestal, remote display Part 1618871−01...
  • Page 77 Parts This page intentionally left blank. Part 1618871−01 E 2020 Nordson Corporation...

  • Page 78: Main Controller Components

    Parts Main Controller Components See Figure 6-3 and the following parts list. DSP_10019246 Figure 6-3 Main Controller Components 1 of 2 (shown with 16 automatic spray gun controller) Part 1618871−01 E 2020 Nordson Corporation...
  • Page 79 Parts Item Part Description Quantity Note 940148 O-RING, silicone, COND, 0.875 X 1.000 1618656 HMI, programmed, Encore Engage 1615492 FAN ASSEMBLY, Engage 326139 PLUG, blanking, 4 mm T 1615880 KIT, service, iFlow module, Engage 148256 PLUG, 10 mm, tubing 1034000 FITTING, ½...
  • Page 80 Parts Main Controller Components (contd) See Figure 6-4 and the following parts list. DSP_10019246 Figure 6-4 Main Controller Components 2 of 2 (shown with 16 automatic spray gun controller) Part 1618871−01 E 2020 Nordson Corporation...
  • Page 81 Ethernet 2, Engage 1618010 RECEPTACLE ASSEMBLY, Ethernet, 0.5 M, Ethernet 3, Engage 900620 TUBING, poly, spiral cut, 3/8 ID 900740 TUBING,polyurethane,10/6.5−7 mm 226690 TUBING, polyurethane, 12/8 mm, blue AR: As Required NS: Not Shown Continued... Part 1618871−01 E 2020 Nordson Corporation...

  • Page 82: Main Controller For Remote Display Components

    Main Controller for Remote Display Components See Figure 6-5 and the following parts list. 13 15 18 19 DSP_10019334 Figure 6-5 Main Controller for Remote Display Components 1 of 2 (shown with 16 automatic spray gun controller) Part 1618871−01 E 2020 Nordson Corporation...
  • Page 83 POWER SUPPLY, 24 Vdc, 600 W 1603591 KIT, PCA, relay board, iControl 2 1618667 SWITCH, LAN/WAN gateway, programmed, Engage 1618666 PLC, programmed, Encore Engage 939953 FUSE, 4A, ceramic, time-delay 1609757 POWER SUPPLY, 24 Vdc, 120 W 1000595 CONTACT BLOCK, 1-N.O. and 1-N.C. contact...
  • Page 84 Main Controller for Remote Display Components (contd) See Figure 6-6 and the following parts list. DSP_10019334 Figure 6-6 Main Controller for Remote Display Components 2 of 2 (shown with 16 automatic spray gun controller) Part 1618871−01 E 2020 Nordson Corporation...
  • Page 85 Ethernet 2, Engage 1618010 RECEPTACLE ASSEMBLY, Ethernet, 0.5 M, Ethernet 3, Engage 900620 TUBING, poly, spiral cut, 3/8 ID 900740 TUBING,polyurethane,10/6.5−7 mm 226690 TUBING, polyurethane, 12/8 mm, blue AR: As Required NS: Not Shown Continued... Part 1618871−01 E 2020 Nordson Corporation...

  • Page 86: Remote Display Components

    6-12 Parts Remote Display Components See Figure 6-7 and the following parts list. DSP_10019168 Figure 6-7 Remote Display Components Part 1618871−01 E 2020 Nordson Corporation...
  • Page 87 GASKET, foam, conductive, ½ x1/2 x 18−1/2 in. 1107695 POWER SUPPLY, 24 Vdc, 60 W 334805 FILTER, line, RFI, power, 10 A 1618656 HMI, programmed, Encore Engage NOTE A: Only applicable for remote display with E-stop. Part 1618871−01 E 2020 Nordson Corporation...

  • Page 88: Auxiliary Controller Components

    6-14 Parts Auxiliary Controller Components See Figure 6-8 and the following parts list. DSP_10019333 Figure 6-8 Auxiliary Controller Components 1 of 2 (shown with 16 automatic spray gun controller) Part 1618871−01 E 2020 Nordson Corporation...
  • Page 89 FUSE, 8A, ceramic, time-delay, 5 x 20 1615873 FILTER, line, RFI, power, DIN rail mount 1615896 SWITCH, disconnect, 6 pole, DIN rail mount 939953 FUSE, 4A, ceramic, time-delay 1615937 POWER SUPPLY, 24 Vdc, 600 W Continued... Part 1618871−01 E 2020 Nordson Corporation...
  • Page 90 6-16 Parts Auxiliary Controller Components (contd) See Figure 6-9 and the following parts list. DSP_10019333 Figure 6-9 Auxiliary Controller Components 2 of 2 (shown with 16 automatic spray gun controller) Part 1618871−01 E 2020 Nordson Corporation...
  • Page 91 CORD SET,POWER ,3 pole, female, 14 AWG, PVC, 6 M 240976 CLAMP, ground, with wire 246458 JUMPER, ground, 4-in. 900740 TUBING,polyurethane,10/6.5−7 mm 226690 TUBING, polyurethane, 12/8 mm, blue AR: As Required NS: Not Shown Part 1618871−01 E 2020 Nordson Corporation...

  • Page 92: Kits

    S VALVE, proportional, solenoid, sub-base 1604437 S KIT FILTER, 20 micron, 0.168 DIA x .125 LG 1604436 S SERVICE KIT, filter, 20 micron, with tool 972125 S CONNECTOR, male, elbow, 10 mm T x ¼ UNI Part 1618871−01 E 2020 Nordson Corporation...

  • Page 93: Dual Manual Spray Gun Interface Kit

    Manual Spray Gun Interface Kit (shown with dual manual gun interdace kit) Item Part Description Quantity Note - - - - - - KIT, Engage, manual gun interface, dual, Encore 1614566 S CONTROL UNIT, interface, Encore, Enhance, packaged 1082739 S BRACKET, rail mount, controller interface, Encore...
  • Page 94 6-20 Parts Part 1618871−01 E 2020 Nordson Corporation...
  • Page 95 - Ambient Temperature: +15ºC to +40ºC - Ex tb IIIB T60ºC / Ex II 2 D / 2mJ = (Encore XT and HD Manual Applicators) - Ex tc IIIB T60ºC Dc / Ex II (2) 3 D = (Enhance Manual Interface Controller) - Ex II (2) D = (Engage Controllers and Remote Display) –...
  • Page 96 MATERIAL NO. REVISION 10018643 REVISIONS NOTICE THIS DRAWING IS NORDSON PROPERTY,CONTAINS PROPRIETARY INFORMATION AND MUST BE RETURNED UPON REQUEST. DESCRIPTION DO NOT CIRCULATE, REPRODUCE OR DIVULGE TO OTHER PARTIES WITHOUT WRITTEN CONSENT OF NORDSON. ZONE REV. ECO NO. DATE ISSUED 25JAN19...
  • Page 97 10018643 REVISIONS NOTICE THIS DRAWING IS NORDSON PROPERTY,CONTAINS PROPRIETARY INFORMATION AND MUST BE RETURNED UPON REQUEST. DESCRIPTION DO NOT CIRCULATE, REPRODUCE OR DIVULGE TO OTHER PARTIES WITHOUT WRITTEN CONSENT OF NORDSON. ZONE REV. ECO NO. DATE SEE SHEET 1 FOR CHANGE DETAILS...

Table of Contents