Video-inserter, compatible with audi vehicles with mmi3g basic/high, mmi3g+ basic/high infotainments vw vehicles with rns850 infotainment and 4pin hsd lvds connector (21 pages)
Video-inserter; compatible with bmw vehicles with business/professional nbt navigation systems or radios with 6.5”, 8.8” or 10.2” monitor with 4 + 2pin hsd lvds connector (20 pages)
Video-inserter for audi vehicles with mmi3g basic/high, mmi3g+ basic/high infotainments, vw vehicles with rns850 infotainment and 4pin hsd lvds connector (21 pages)
Summary of Contents for r.LiNK RL3-UCON8-LV
Page 1
Video-inserter RL3-UCON8-LV Compatible with Maserati vehicles with Uconnect VP4-NA and 8.4 inch monitor Video-inserter with 2 video inputs, rear-view camera input and CAN control Product features Video-inserter for factory infotainment systems 2 CVBS video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner, …) ...
Case 1: Video-interface receives the reverse gear signal 2.6.2.2. Case 2: Video interface does not receive the reverse gear signal 2.7. Connection video-interface - keypad 2.8. Picture settings 3. Interface operation 4. Specifications 5. FAQ – Trouble shooting 6. Technical support Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
Due to changes in the production of the vehicle manufacturer there’s always a possibility of incompatibility. 1.1. Delivery contents Take down the serial number of the interface and store this manual for support purposes: ____________________ Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
Factory rear-view camera Automatically switching-back from inserted video to factory rear-view camera is only possible while the reverse gear is engaged. To delay the switch-back, an additional electronic part is required. Video input signal Only NTSC compatible Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
Try all possible combinations of dip 7 and 8 to find the Monitor selection best picture (quality and size) See the following chapters for detailed information. After each Dip-switch-change a power-reset of the Can-box has to be performed! Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
Before a final installation, we recommend a test-run to ensure the compatibility of the vehicle and the interface. Due to changes in the production of the vehicle manufacturer there’s always a possibility of incompatibility. Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
2.1.1. Place of installation – video-interface The video-interface has to be installed on the backside of the head-unit. 2.1.2. Place of installation - daugter PCB The daughter PCB has to be installed inside the head unit. Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
2) The ribbon cable’s contacting side always has to correspond to the contacting side of the connector, concerning the mounting position. 3) Avoid cable contusion or cable injury caused by sharp-edged metal. Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
2.4. Connection to head unit – picture signal cable Connect the picture signal cable’s beige coloured female 20pin connector which is lead out from the head unit, to the male 20pin connector of the video-interface. Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
10pin Power / CAN cable’s male 52pin connector. Connect the 10pin Power / CAN cable’s female 52pin connector to the male 52pin connector of the head-unit. Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
Connect the female 12pin connector of the 12pin interface cable to the male 12pin connector of the video interface. Connect the single red wire ACC-out (max 3A) and the purple coloured wire Manual of the 12pin interface cable to +12V S-contact terminal 86s (e.g. glove compartment illumination). Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
Page 14
Connect the video RCA of the video source 1 and 2 to the female RCA connector “Video IN1” ”Video IN 2” of the 12pin interface cable. Connect the video RCA of the Rear-view camera to the female RCA connector “Camera IN” of the 12pin interface cable. Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
12pin cable should carry +12V while the reverse gear is engaged. See the following illustration for the according connection. Note: Do not forget to set dip5 of the video-interface to ON before testing. Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
The 12 V power supply for the rear-view camera (max 3A) should be taken from the green wire of the 20pin cable to avoid an unnecessary permanent power supply to the camera electronic. For the operation, both green cables “Reverse IN” “Reverse OUT” have to stay connected. Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
Page 17
Connect the output connector (87) of the relay to the rear-view camera’s power- cable, like you did it to the green “Reverse-IN” cable before. Connect permanent power / 12V to the relay’s input connector (30). Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
Connect the keypad’s female 4pin connector to the video-interface’s male 4pin connector. Note: Even if the switching through several video sources by the keypad mightn’t be required, the invisible connection and availability is strongly recommended. Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
Contrast Brightness Saturation Position H (horizontal) Position V (vertical) For the rearIR-AV1 (out of function) IR-AV2 (out of function) Guide-lines left (out of function) Guide-lines right (out of function) Guide lines (ON/OFF) (out of function) Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
NTSC RGB-video amplitude 0.7V with 75 Ohm impedance Temperature range -40°C to +85°C Dimensions Video-Box 118 x 25 x 88 mm (W x H x D) Dimensions daughter PCB 110 x 7 x 92 mm Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
Camera input picture fluorescent light which shines Test camera under natural light outside the garage. flickers. directly into the camera. Camera input picture is Protection sticker not Remove protection sticker from lens. bluish. removed from camera lens. Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...
Please note that direct technical support is only available for products purchased directly from NavLinkz GmbH. For products bought from other sources, contact your vendor for technical support. NavLinkz GmbH distribution/tech dealer-support Eurotec-Ring 39 D-47445 Moers +49 2841 949970 Email mail@navlinkz.de 10R-03 5384 Made in China Version 12.09.2019 HW: CAM(V97) RL3-UCON8-LV...