Table of Contents
Advertisement
Quick Links
r.LiNK Video-inserter
RL2-RLINK
Compatible with
Dacia, Fiat, Smart and Renault vehicles
with RLink or MediaNav system
and Opel vehicles with Navi 50 or Navi 80
Video-inserter with 2 video inputs and rear-view camera input
Product features
Video-inserter for factory-infotainment systems
2 video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner)
Rear-view camera video-input
Automatic switching to rear-view camera input on engagement of the reverse gear
Activatable parking guide lines for rear-view camera (not for all vehicles available)
Video-in-motion (ONLY for connected video-sources)
Video-inputs PAL / NTSC compatible
Version 22.08.2018
HW CAM(V31)/(V22)
RL2-RLINK
Advertisement
Table of Contents
Related Manuals for r.LiNK RL2-RLINK
Summary of Contents for r.LiNK RL2-RLINK
- Page 1 Video-inserter RL2-RLINK Compatible with Dacia, Fiat, Smart and Renault vehicles with RLink or MediaNav system and Opel vehicles with Navi 50 or Navi 80 Video-inserter with 2 video inputs and rear-view camera input Product features Video-inserter for factory-infotainment systems ...
-
Page 2: Table Of Contents
Case 2: CAN-box does not detect reverse gear 2.7. Connecting video-interface and keypad 2.8. Picture settings and parking guide lines 3. Interface operation 3.1. By VOL-Button 3.2. By external keypad Specifications Frequently asked questions Technical support Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... -
Page 3: Prior To Installation
1. Prior to installation Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. 1.1. Delivery contents Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... -
Page 4: Checking The Interface Compatibility Of Vehicle And Accessories
Further it reads the vehicle’s digital signals out of the vehicle’s CAN-bus and converts them for the video interface. Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... -
Page 5: Dip-Switch Settings
If set to ON, the interface switches to its rear-view camera input while the reverse gear is engaged. 1.3.1.4. Monitor selection (dip6, 7-and 8) Set to OFF Note: Dip 1 and 4are out of function and have to be set to OFF. Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... -
Page 6: Can-Box
2.1.2. Place of installation - daughter PCB The interface’s daughter PCB is prepared to be installed between the head unit’s housing and the monitor panel. For this purpose the housing of head-unit have to be opened. Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... -
Page 7: Connection Scheme
2.2. Connection Scheme Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... -
Page 8: Connecting Video-Interface And Can-Box
CAN, it is possible to install the system without CAN-box. In this case, see also the note in chapter “after-market rear-view camera”, how the interface is supposed to be connected without CAN-Box. Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... - Page 9 20pin connector of the interface. Take care for installing the cable in the right direction as both connectors seem to be identical. (Take notice of the wire`s caption “MONITOR SIDE” and “BOX SIDE” Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK...
-
Page 10: Warning Notes, Concerning The Installation Of Ribbon Cables
180° position to the connector. Each deviation from a perfect contact position will curse faulty contact and even danger of short circuit 2) The ribbon cable’s contacting side always has to correspond to the contacting side of the connector, concerning the mounting position. Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... -
Page 11: Warning Notes, Concerning The Installation Of Ribbon Cables
180° position to the connector. Each deviation from a perfect contact position will curse faulty contact and even danger of short circuit 2) The ribbon cable’s contacting side always has to correspond to the contacting side of the connector, concerning the mounting position. Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... -
Page 12: Medianav With 50Pin Ribbon Cable
24pin Connector of PNP Power/CAN Cable Kit. Connect the 24pin-connector of PNP Power/CAN Cable to the 24pin-connector at the Monitor`s Rear side. Attach the daughter PCB at the outer side of monitor by using the enclosed longer screws for perfect mounting. Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... -
Page 13: Connection Of Video Sources
Note: The picture settings for CAM input have to be adjusted in AV2. Connect the RCA of the video source 1 and video source 2 to the female RCA „Video IN1“ and „Video IN2“ of the video cable. Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... -
Page 14: Audio-Insertion
„CAMERA IN“ while the reverse gear is engaged. Additionally, the +12V (max. 500mA) power supply for the rear-view camera can be taken from the green wire of the 6pin to 8pin cable. Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... - Page 15 Connect the rear-view camera power wire and the green wire (video interface side) of the 6pin to 8pin cable both to output terminal (87) of the relay. Connect permanent battery power to input terminal (30) of relay. Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK...
-
Page 16: Connecting Video-Interface And Keypad
Connect the keypad’s female 4pin connector to the male 4pin connector of the video- interface. Note: Even if the switching through several video sources by the keypad mightn’t be required, the keypad’s invisible connection and availability is strongly recommended. Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... -
Page 17: Picture Settings And Parking Guide Lines
Note: If there is no communication between the CAN box and the vehicle`s CAN-bus (several vehicles aren’t compatible), the reverse gear guide-lines can`t be shown during the vehicle’s operation, even if they once appear after having switched the system to powerless! Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... -
Page 18: Interface Operation
0.7V with 75 Ohm impedance Temperature range -40°C to +85°C Dimensions video-box 113 x 22 x 96mm (W x H x D) Dimensions CAN-box 70 x 22 x 42 mm (W x H x D) Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK... - Page 19 Camera input picture fluorescent light which shines Test camera under natural light outside the garage. flickers. directly into the camera. Camera input picture is Protection sticker not Remove protection sticker from lens. bluish. removed from camera lens. Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK...
-
Page 20: Technical Support
Please note that direct technical support is only available for products purchased directly from NavLinkz GmbH. For products bought from other sources, contact your vendor for technical support. NavLinkz GmbH distribution/tech dealer-support Eurotec-Ring 39 D-47445 Moers +49 2841 949970 Email mail@navlinkz.de 10R-03 5384 Made in China Version 22.08.2018 HW CAM(V31)/(V22) RL2-RLINK...
Need help?
Do you have a question about the RL2-RLINK and is the answer not in the manual?
Questions and answers