Table of Contents
Advertisement
Quick Links
H-3827, H-3828
π
H-3829, H-3830
ADVENTURER PRO
BALANCE SCALES
UNPACKING
Carefully remove your Adventurer Pro balance and
each of its components from the package. Save the
packaging to ensure safe storage and transport.
ASSEMBLY OF MODELS H-3829 & H-3830
1.
Insert the Sub-platform on the Mounting Cone
located in the center of the balance. Align the
Sub-platform so that it is fully seated on the Cone.
(See Figure 1)
2. Place the Weighing Pan on the Sub-platform.
(See Figure 1)
3. For applicable Adventurer Pro models, place the
Wind Ring over the pins located on the perimeter of
the balance.
Figure 1
Weighing Pan
Wind Ring
(INCAL models)
Pin
PAGE 1 OF 8
1-800-295-5510
uline.com
INSTALLATION
Sub-platform
Mounting Cone
INSTALLING COMPONENTS
Use the illustrations and instructions below to identify
and assemble your Adventurer Pro model with its com-
ponents. All components must be installed before using
the balance.
ASSEMBLY OF MODEL H-3827
1.
Insert the Sub-platform on the Mounting Cone
located in the center of the balance.
2. Place the Weighing Pan on the Sub-platform.
(See Figure 2)
3. Place the Wind ring over the shoulder of the
balance. (See Figure 2)
Figure 2
Weighing Pan
Sub-platform
Wind ring
Shoulder
Mounting Cone
0313 IH-3827
Advertisement
Table of Contents
Related Manuals for U-Line ADVENTURER PRO Series
Summary of Contents for U-Line ADVENTURER PRO Series
- Page 1 H-3827, H-3828 π 1-800-295-5510 H-3829, H-3830 uline.com ADVENTURER PRO BALANCE SCALES INSTALLATION UNPACKING INSTALLING COMPONENTS Carefully remove your Adventurer Pro balance and Use the illustrations and instructions below to identify each of its components from the package. Save the and assemble your Adventurer Pro model with its com- packaging to ensure safe storage and transport.
-
Page 2: Selecting The Location
INSTALLATION CONTINUED ASSEMBLY OF MODEL H-3828 • Hold and position each door so that the handle is near the front of the balance and the small notch Insert the Sub-platform on the Mounting Cone on the bottom edge of the door is lined up with located in the center of the balance. -
Page 3: Operation
OPERATION TURNING POWER ON AND OFF Press the On/Zero button to turn power on. The balance performs a segment check. The balance then displays the last selected application mode. To turn power off, press and hold the Off button until OFF is displayed, then release the button. -
Page 4: Changing Application Modes
OPERATION CONTINUED CHANGING UNITS OF MEASURE CONTINUED EXIT THE MENU To select a unit of measure, press and hold the Press the Exit button at any time to quickly exit the menu Unit button, then release it when the desired unit is or select END sub-menu and press the Yes button. -
Page 5: Display Hold
OPERATION CONTINUED PARTS COUNTING CONTINUED 2. Remove the reference weight and place the ESTABLISH AN AVERAGE PIECE WEIGHT (APW) item to be compared on the pan. The balance CONTINUED indicates the actual percentage on the primary 6. To change the sample display. -
Page 6: Dynamic/Animal Weighing
OPERATION CONTINUED TOTALIZE EDITING LIMITS The limits are edited one digit Totalize measures the cumulative weight of items. at a time. The digit being Press Mode, then release the button when Totalize is edited is blinking. Its value can displayed. The primary display shows the current weight. be incremented by pressing The secondary display alternates between TOTALIZE and the No button or decremented... -
Page 7: Additional Features
OPERATION CONTINUED DYNAMIC/ANIMAL WEIGHING BATTERY OPERATION CONTINUED Models with the battery operation feature will display the battery change indicator as shown below. AUTOMATIC MODE If batteries are installed and AC power is not present, the balance operation is affected as follows: The balance returns to the Ready condition when the animal is removed from the pan. -
Page 8: Troubleshooting
TROUBLESHOOTING The following table lists common problems, possible causes and remedies. If the problem persists, contact Uline Customer Service. OPERATING ISSUE CAUSES RECOMMENDATIONS Balance will not turn on. AC power not connected. Connect AC adapter. Batteries discharge. Replace batteries. Battery indicator is flashing. Batteries are weak.
Need help?
Do you have a question about the ADVENTURER PRO Series and is the answer not in the manual?
Questions and answers