Table of Contents
Advertisement
DXP HD 4K PLUS Series • Setup Guide (Continued)
2.
Press the desired input or output button (see the illustration at right).
3.
Press the Enter button.
Power Save Modes
Power save modes are selectable only by SIS commands. Three modes are
available:
•
0 — Normal (full power) operation (default).
•
1 — Disables all functions except RS-232, USB, and IP control, and
reduces cooling fan speed. This mode is cancelled if power is cycled,
any front panel buttons are pressed, PCS is opened, or any SIS commands are sent via RS-232, USB, or IP.
•
2 — Locks the front panel, reduces cooling fan speed, and disables all functions except RS-232, USB, PCS, and IP control.
This mode can be cancelled only by entering the SIS command
NOTE:
The green front panel Video LED blinks while the DXP is in power save mode 1 or 2.
Locking and Unlocking the Front Panel (Executive Mode)
The DXP switcher has three levels of security lock that limit the operation of the switcher from the front panel:
•
Lock mode 0 — The front panel is completely unlocked.
•
Lock mode 1 — All front panel functions are locked (except for setting lock mode 2). Some functions can be viewed.
•
Lock mode 2 — Basic functions are unlocked. Advanced functions, such as setting video and audio mute, are locked and
can be viewed only (see the table below). The switcher is shipped from the factory in this mode.
Basic Functions
•
Making ties
•
Saving and recalling presets
•
Changing lock modes
Selecting front panel lock mode 2 or toggling between lock modes 2 and 0
NOTES:
•
If the switcher is in lock mode 0 or 1, this procedure selects mode 2.
•
If the switcher is in lock mode 2, this procedure selects mode 0 (unlocks
the switcher).
•
Toggle the front panel lock on and off by pressing and holding the Enter,
Video, and Audio buttons simultaneously until the following buttons blink twice
(approximately 2 seconds).
If the DXP is now in lock mode 2, the Escape, Video, and Audio buttons
•
blink twice.
If the DXP is now in lock mode 0, the Video and Audio buttons blink twice.
•
Selecting front panel lock mode 2 or toggling between lock modes 2 and 1
NOTES:
•
If the switcher is in lock mode 1, this procedure selects mode 2.
•
If the switcher is in lock mode 2, this selects mode 1 (locks all switcher functions
except selecting mode 2).
Toggle the lock on and off by pressing and holding the Video and Audio buttons until
•
the following buttons blink twice (approximately 3 seconds).
If the DXP is now in lock mode 2, the Escape, Video, and Audio buttons blink
•
twice.
If the DXP is now in lock mode 1, the Video and Audio buttons blink twice.
•
NOTE:
To switch from lock mode 1 (the front panel is completely locked) to lock mode 0 (the front panel is unlocked), you
must first switch to mode 2, then from mode 2 to mode 0.
8
E
Advanced Functions
•
Setting video and audio output mutes
•
Setting the RS-232 port baud rate
Press and release the desired input or output button.
1
2
3
The button blinks to indicate this preset number is
selected to save or recall.
CONTROL
ENTER
PRESET
ESCAPE
VIEW
}
0 PSAV
or opening PCS.
Press and hold Enter, Video, and Audio buttons
simultaneousely to enable lock mode 2 or toggle
between mode 2 and mode 0.
CONTROL
ENTER
PRESET
VIEW
2 seconds
CONTROL
ENTER
PRESET
VIEW
Press and hold Video and Audio buttons
simultaneousely to enable lock mode 2
or toggle between mode 1 and mode 2.
ENTER
PRESET
INPUTS
4
5
6
7
8
The Enter button blinks
to indicate the need to
I/O
VIDEO
AUDIO
ESCAPE
2 seconds
I/O
ESCAPE
VIDEO
AUDIO
I/O
VIDEO
AUDIO
2 secounds
CONTROL
I/O
ESCAPE
VIDEO
AUDIO
VIEW
Advertisement
Table of Contents
