Extron electronics DXP 1616 HD 4K PLUS Series Setup Manual page 3

B Output connectors — Connect HDMI output devices to these female 19-pin type A HDMI output connectors for buffered
video output (see Securing HDMI Cables with the LockIt HDMI Cable Lacing Bracket
C Reset LED — While you are holding the Reset button, this green LED blinks every 3 seconds to indicate the
level of reset that will occur if the button is released at that point (see
D
Reset button — This recessed button initiates three levels (modes) of reset. Use a pointed object such as a small
screwdriver to press and hold the Reset button.
Factory firmware reset (mode 1) — Hold the Reset button while powering up the switcher to restore the DXP to
•
the factory firmware for a single power cycle. This type of reset maintains all the current user settings, such as audio
adjustments, IP settings, and the configuration.
IP settings reset (mode 4) — While the DXP is running, press and hold the Reset button until the LED blinks twice
•
(approximately 6 seconds). Release the button and press it again momentarily to reset the switcher IP functions. This
reset does not replace any user-installed firmware.
Absolute reset (mode 5) — While the DXP is running, press and hold the Reset button until the LED blinks three times
•
(approximately 9 seconds). Release the button and press it again momentarily to restore the switcher to the default
factory conditions.
E
Remote RS-232 connector — Connect an RS-232 capable host
device such as a computer or a touchpanel control to this 3.5 mm
3-pole captive screw connector to configure and control the
switcher via SIS commands. Connect the 9-pin end of the RS-232
cable to the serial port of your computer or control system. The
default port parameters are 9600 baud, 8 data bits, 1 stop bit, no
parity.
F LAN port — Connect a computer, a network switch, or a control
system to this RJ-45 connector. With the Ethernet connection, you
can use a computer to configure and control the networked
switcher with SIS commands, the PCS configuration program, or
the embedded HTML page.
Ethernet connection indicators — The Link and Act
LEDs indicate the status of the Ethernet connection.
Link — Indicates that the switcher is properly
•
connected to an Ethernet LAN. This green LED should light
steadily.
Act (Activity) — Indicates transmission of data on the RJ-45
•
connector. This amber LED should flicker as the switcher
communicates.
Ethernet links use Category (CAT) 3, 5e, or 6 unshielded twisted pair (UTP) or shielded twisted pair (STP) cables, terminated
with RJ-45 connectors. Ethernet cables are limited to 328 feet (100 meters).
NOTES:
• Do not use standard telephone cables. Telephone cables do not support Ethernet or Fast Ethernet.
• Do not stretch or bend the cables because this can cause transmission errors.
Crossover Cable
Pins:
1 2 3 4 5 6 7 8
End 1
Pin Wire Color
1 White-green
2 Green
3 White-orange
4 Blue
5 White-blue
6 Orange
7 White-brown
Insert Twisted
8 Brown
Pair Wires
T568A
RJ-45
Connector
A cable that is wired as T568A at one end
and T568B at the other (Tx and Rx pairs
reversed) is a "crossover" cable.
Figure 3. RJ-45 Connector and Pinout Tables
Straight-through Cable
End 2 End 1
Wire Color Pin Wire Color
White-orange 1 White-orange
Orange 2 Orange
White-green 3 White-green
Blue 4 Blue
White-blue 5 White-blue
Green 6 Green
White-brown 7 White-brown
Brown 8 Brown
T568B T568B
A cable that is wired the same at both ends
is called a "straight-through" cable because
no pin or pair assignments are swapped.
Both ends of the cable can be T568B (as shown)
or T568A (not shown).
figure 2, D , on the previous page).
Tx Rx G
DXP HD 4K PLUS
Rear Panel
RS-232 Port
Tx Rx G
NOTES:
• If you use cable that has a drain wire, tie
the drain wire to ground at both ends.
• Connect a ground wire between the DXP
LAN
and the computer or control system.
Ground (G)
Receive (Rx)
Transmit (Tx)
End 2
Wire Color
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
Default Ethernet settings:
T568B
• IP address — 192.168.254.254
• Subnet mask — 255.255.0.0
• Gateway address — 0.0.0.0
on page 4).
Transmit (Tx)
Receive (Rx)
Computer or
Control System
RS-232 Port
3